• 대한기계학회논문집A
• /
• 제35권9호
• /
• pp.977-982
• /
• 2011

보강롤 구동 4 단 냉간압연기에서 작업롤과 보강롤 사이의 접촉력으로 인해 발생된 작업롤의 수평력을 고찰하였다. 본 수평력은 작업롤을 수평방향으로 휘게하고 롤갭 형상을 그 만큼 변화시킨다. 본 논문에서는 압연을 정상상태라고 가정하여 작업롤의 수평력을 예측할 수 있는 수식모델을 제시하였다. 해석에 사용된 소재는 고-실리콘(약 3%) 강판이었다. 수평력의 비-정상거동을 고찰하기 위해서 삼차원 유한요소모델을 채용하였다. 두 가지 모델을 이용하여 작업롤의 수평력은 보강롤의 중심으로부터 작업롤의 중심이 벗어난 길이에 따라 변한다는 결과를 얻었다. 그리고 작업롤의 수평력을 최소화 시킬 수 있는 작업롤의 최적 중심이탈 길이를 도출하였다.

• 대한기계학회논문집
• /
• 제19권1호
• /
• pp.292-300
• /
• 1995

According to the number of cold-rolled coils, the amount of roll wear and thermal expansion, and roll gap profile were calculated, by using the actual data from the finishing mill. Also, based on those data, the calculations of the deflection, the flattening, and the contact pressure of vwork rolls and backup rolls were made respectively. Specially, in the calculation of contact pressure, the numerical results were obtained not only during the normal rolling, but also during the abnormal rolling, by modeling mathematically the dynamic impact force which occurs when the head section of the strip is threading through rolls. With those results the growth of the fatigue region and the fatigue damage of rolls were predicted. Also the optimum roll-grinding depth was determined to maximize the roll life.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1993년도 추계학술대회 논문집
• /
• pp.499-504
• /
• 1993

To find a way for establishing work roll initial crown according to roll conditions, computer simulation for predicting plate crown in plate mill is done and effects of roll conditions on plate crown is analysed. Roll gap profile and plate crown are measured to be compared to the calculated values. As a result,a regression equation to establish work roll initial crown according to roll cooditions such as backup roll diameter, backup roll crown and work roll crown is obtained.

• 대한기계학회논문집
• /
• 제17권2호
• /
• pp.257-266
• /
• 1993

본 연구에서는 보강롤의 굽힘변형을 고려한 젠지미어 압연기의 롤변형 해석을 통해, 궈터웨이브의 발생을 시뮬레이션하고, 형상제어 수단들의 궈터웨이브 억제에 미 치는 영향을 분석하여 궈터웨이브 감소 방안을 수립하였고, 실제 현장 압연실험을 통 해 그 제어효과를 확인하였다.

• 한국기계가공학회지
• /
• 제8권4호
• /
• pp.129-135
• /
• 2009

In this paper, a finite element model is presented for the prediction of roll force and strip thickness in a backup-roll-drive mill. The proposed FE model is focused mainly on analyzing the elastic/plastic behavior between a work roll and a strip as well as the rigid/plastic behavior between a backup roll and a work roll. The capability of the proposed model is demonstrated through application to 4-high silicon steel rolling mill at POSCO. Results show that the predicted roll force and strip thickness rolled accurately agree with the measured them. It is also illustrated that the proper position of work roll displaced to one side from the vertical centerline of the backup-roll may be determined by minimizing the horizontal force of work roll.

• 대한기계학회논문집A
• /
• 제27권2호
• /
• pp.327-333
• /
• 2003

Most of shape defects in steel strip are originated from the structure of rolling mill itself. For instance, strip crown occurs when the work roll is deformed by the bending moment induced on roll chocks. To get rids of the shape defects, it is necessary to increase the stiffness of rolling mill. The structure change of back-up roll is one of alternative ways to increase the mill stiffness without facility revamping from 4 high mill to 6 high mill. In this research work, the new back-up roll was developed and can be used in any type of 4 high mill to reduce the strip shape defects. The developed back-up roll consists of sleeve, arbor and phase angle adjusting system for arbor. The circumference of arbor is specially machined to adapt the strip width change during rolling. The experimental cold rolling test was done to prove the effectiveness of newly developed back-up roll. The experimental rolling results show that the new back-up roll has more powerful performance in reducing the shape defects than conventional back-up roll. It was also found that the new back-up roll has higher stability for shape control. In addition to, the only sleeve surface needs to be reground and changed in most cases, so that the maintenance cost can be greatly reduced.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.160-163
• /
• 2003

For the purpose of rolling hard metals such as silicon steel and non-ferrous metals, the backup roll driven-type mill has been widely used in cold rolling industry. Since the backup roll drive results in horizontal bending of the work rolls and therefore exerted reciprocal action on the roll gap contour, the selection of slim work rolls is very restricted. In this paper, we present an analytic equation based scheme to determine a proper horizontal position of work roll minimizing the horizontal force subject to mechanical constraints.

• 한국정밀공학회지
• /
• 제29권8호
• /
• pp.840-844
• /
• 2012

Roll forming process is a sheet metal forming process where the forming occurs with rolls in several steps, often from an undeformed sheet to a product ready to use. And each pair of forming rolls installed in a forming machine operates a particular role in making up the required final cross-section. This process used to many industry manufactures and recently apply to automotive industry. This study, FEM simulation applied bumper reinforcement using SHAPE-RF software and analyzed about total effective strain, longitudinal strain, thickness according to the roll-pass.

• 한국공작기계학회논문집
• /
• 제15권6호
• /
• pp.22-31
• /
• 2006

When ironwork, especially steel roll coil, is transported to customers, land transportation and sea transportation are usually used. To transport steel roll coil fast and safe without damaging it, it is necessary that the steel roll coil has to be in stable condition. These days, apitong, which is all imported from overseas, is being used to support the steel roll coil, but because of apitong's rigidity, it damages the coil and when the coil is damaged, it is hard to fix. Due to the fact that recovering damage of the coil is almost impossible, we have to find the new type of dunnage that can substitute the apitong. In this paper, the arrays and the kinds of reinforcements, and rectangular type and trapezoid of dunnage will be talked about. The phenomenon of rolling and the impact when the carrier start moving and stop will be talked about as well. Therefore, we are going to develop a dunnage that does not damage ironwork and has better recovery and softness than existing apitong dunnage.

• 한국지반신소재학회논문집
• /
• 제13권4호
• /
• pp.97-107
• /
• 2014

본 논문에서는 표준트럭하중을 받는 연약지반에 놓인 롤타입 강재매트의 모델링과 해석을 수행하였다. 롤 타입 강재매트는 접근성이 제한된 동토지역에서 손쉬운 현장운반을 위해 원형으로 접을 수 있는 강재매트를 의미하며, 동토지반의 융해로 형성되는 연약지반을 통과하는 비포장도로의 급속보강을 위해 개발되었다. 해석 모델은 강재매트 연결부의 비선형적 거동특성을 모사할 수 있는 연결요소, 강재매트의 휨강성을 갖는 쉘요소, 지반특성을 고려한 스프링 구속으로 구성된다. 또한 각 해석요소들의 구조적 거동은 각 모델링 단계에서 실험과 해석을 통해 검증되었다. 링크요소가 없는 빔과 쉘 요소해석이 수행되었으며, 본 연구에서 제시된 해석모델의 결과와 비교하였다. 해석결과, 본 연결부를 고려한 쉘 해석모델의 수직 처짐 결과가 다른 모델에 비하여 상당히 큰 것으로 확인되었다. 따라서, 느슨한 모래지반에 놓인 롤 타입 강재매트의 해석모델은 면밀한 변수해석 연구에 근거하여야 함을 알 수 있다.