• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.9
• /
• pp.42-51
• /
• 2017

This paper deals with the power supply facility providing wireless power transmission for a type of electric vehicles called the on-line electric vehicle(OLEV) and proposes optimal protection coordination methods which analyze the faultsin the 60Hz and 20kHz bands using PSCAD/EMTDC, which is the typical commercial software for the distribution system. The simulation results show that the proposed methods can reduce the fault current by introducing an NGR (Neutral Ground Resistor) in the 60Hz band and prevent the malfunctioning of the protection device by installing a CT in the neutral wire in the 20kHz band when a ground fault occurs.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.8
• /
• pp.25-32
• /
• 2011

Networks-on-chip (NoC) is emerging as a key technology to overcome severe bus traffics in ever-increasing complexity of the Multiprocessor systems-on-chip (MPSoC); however traditional electrical interconnection based NoC architecture would be faced with technical limits of bandwidth and power consumptions in the near future. In order to cope with these problems, a hybrid optical NoC architecture which use both electrical interconnects and optical interconnects together, has been widely investigated. In the hybrid optical NoCs, wormhole switching and simple deterministic X-Y routing are used for the electrical interconnections which is responsible for the setup of routing path and optical router to transmit optical data through optical interconnects. Optical NoC uses circuit switching method to send payload data by preset paths and routers. However, conventional hybrid optical NoC has a drawback that concurrent transmissions are not allowed. Therefore, performance improvement is limited. In this paper, we propose a new routing algorithm that uses circuit switching and adaptive algorithm for the electrical interconnections to transmit data using multiple paths simultaneously. We also propose an efficient method to prevent livelock problems. Experimental results show up to 60% throughput improvement compared to a hybrid optical NoC and 65% power reduction compared to an electrical NoC.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.158-158
• /
• 2017

비닐포장 하부에 위치한 콩의 생장 초기에 발생한 초엽을 인식하기 위한 연구를 수행중이다. 선행 연구에서 비닐포장에 접촉한 콩 초엽으로 인해 비닐포장 상부 표면의 열 반응 분포에 변화가 있음을 발견하였다. 현장에서 주행 중에 콩 초엽의 위치를 실시간으로 인식하고 연동된 선형 또는 회전형 엑츄에이터를 제어하여 정확한 위치에 천공을 수행하기 위해서는 계측 시스템과 제어 시스템간의 시간적 차이를 최소할 수 있는 실시간 신호 처리 기술이 필수적이다. 선행 연구에서 사용한 다중 IR 센서의 분해능은 $16{\times}4pixel$이며 주파수는 3 Hz로, 폭이 30cm 내외인 비닐포장 상부의 정밀 분석에 한계가 있음을 발견하였다. 이를 해결하기 위하여 분해능과 계측 주기를 개선할 수 있는 초소형 ($1cm{\times}1cm{\times}1cm$) 열화상 센서를 이용하였다. LWIR(Longwave infrared)영역에 해당하는 $8{\mu}m{\sim}14{\mu}m$의 영역에서 $0.05^{\circ}C$의 분해능을 보이는 $ Lepton^{TM}$ (500-0690-00, FLIR, Goleta, CA)모델을 사용하였다. 프레임당 $80{\times}60$ 픽셀의 정보가 2 Byte의 단위로 계측이 되며 9 Hz의 주파수로 대상면의 열 분포를 측정할 수 있다. 이론적으로 초당 정보 전송량은 86,400 Byte ($80{\times}60{\times}2{\times}9$)이며, 1 m를 진행하는 주행형 천공기에 적용할 경우 1 프레임당 10cm 정도의 면적을 측정하므로, 최대 위치 판정 분해능은 약 10 cm / 60 pixel = 0.17 cm/pixel로 상대적으로 정밀한 위치 판별이 가능하다. $80{\times}60{\times}2Byet$의 정보를 0.1초 이내에 분석해야 하는 기술적 과제를 해결하기 위하여 천공 작업기에 적합한 상용 SBC(Single board computer)의 클럭 속도(1 Ghz)로 처리 가능한 공간 분포 분석 알고리즘을 개발하였다. 전체 이미지 도메인을 한 번에 분석하는데 소요되는 시간을 최소화하기 위하여 공간정보 행렬을 균등히 배분하고 별도의 프로세서에서 Feature를 분석한 후 개별 프로세서의 결과를 경합식으로 판정하는 기술을 연구하였다. 오픈 소스인 MPICH(www.mpich.org) 라이브러리를 이용하여 개발한 신호 분석 프로그램을 클러스터링으로 연동된 개별 코어에 설치/수행 하였다. 2D 행렬인 열분포 정보를 공간적으로 균등 분배하여 개별 코어에서 행렬의 Spatial domain analysis를 수행하였다. $20{\times}20$의 클러스터링 단위를 이용할 경우 총 12개의 코어가 필요하였으며, 초당 10회의 연산이 가능함을 확인하였다. 병렬 클러스터링 기술을 이용하여 1m/s 내외의 주행 속도에 대응이 가능한 비닐포장 상부 열 분포 분석 시스템을 구현하였다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.5
• /
• pp.1037-1050
• /
• 2000

A goal of a BISDN network is to provided integrated transport for a wide range of applications such as teleconferencing, Video On Demand etc. There require multipoint communications in addition to conventional point-to-point connections. Therefore multicast capabilities are very essential in multimedia communications. In this paper, we propose a new multicast cell scheduling method on the Parallel Multicast Packet Switch with Ring network: PMRN which are based on separated HOL. In this method, we place two different HOLs, one for unicast cells and the other for multicast cells. Then using non-FIFO scheduling, we can schedule both unicast cells and multicast cells which are available at the time in the input buffer. The simulation result shows that this method reduces the delay in the input buffer and increases the efficiency of both point-to-point network and ring network and finally enhances the bandwidth of the overall packet switch. A goal of a BISDN network is to provided integrated transport for a wide range of applications such as teleconferencing, Video On Demand etc. There require multipoint communications in addition to conventional point-to-point connections. Therefore multicast capabilities are very essential in multimedia communications. In this paper, we propose a new multicast cell scheduling method on the Parallel Multicast Packet Switch with Ring network: PMRN which are based on separated HOL. In this method, we place two different HOLs, one for unicast cells and the other for multicast cells. Then using non-FIFO scheduling, we can schedule both unicast cells and multicast cells which are available at the time in the input buffer. The simulation result shows that this method reduces the delay in the input buffer and increases the efficiency of both point-to-point network and ring network and finally enhances the bandwidth of the overall packet switch.

• Journal of Broadcast Engineering
• /
• v.15 no.2
• /
• pp.205-216
• /
• 2010

In this paper, a method of MPEG-2 Transport Stream (TS) multiplexing for Ultra HDTV (UHDTV) and its design and implementation as a SW tool is described. In practice, UHD video may be divided into several HD videos and each video is encoded in parallel. Therefore, it is necessary to synchronize and multiplex multiple bitstreams encoding each HD video for transmitting and storing UHD video. In this paper, it is assumed that 4 HD videos partitioning a UHD spatially are encoded as H.264/AVC and two 5.0 channel audios are encoded by AC-3. Therefore, 4 H.264/AVC elementary streams (ESs) and 2 AC-3 ESs is mainly considered in the TS multiplexing of UHD. For the carriage of H.264/AVC and AC-3 over MPEG-2 TS, PES packetization and TS multiplexing are designed and implemented based on the extended specification of the MPEG-2 Systems and ATSC (Digital audio compressed standard), respectively. The implemented UHD TS multiplexing tool emulates real time HW operation in the time unit corresponding to the duration of one TS packet transmission in a given TS rate. In particular, in order to satisfy the timing model, the buffers defined in the TS System Target Decoder (T-STD) are monitored and their statuses are considered in the scheduling of TS multiplexing. For UHD multiplexing, two kinds of multiplexing structures, which are UHD re-multiplexing and UHD program multiplexing, are implemented and their strength and weakness are investigated. The developed UHD TS multiplexing tool is tested and verified in terms of the syntax and semantics conformance and functionalities by using a commercial analyzer and real-time presentation tools.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39A no.7
• /
• pp.424-430
• /
• 2014

In this paper, we propose a compressed sensing-based signal recovery technique for an uplink multi-user spatial modulation (MU-SM) system. In the MU-SM system, only one antenna among $N_t$ antennas of each user becomes active by nature. Thus, this characteristics is exploited for signal recovery at a base station. We modify the conventional orthogonal matching pursuit (OMP) algorithm which has been widely used for sparse signal recovery in literature for the MU-SM system, which is called MU-OMP. We also propose a parallel OMP algorithm for the MU-SM system, which is called MU-POMP. Specifically, in the proposed algorithms, antenna indices of a specific user who was selected in the previous iteration are excluded in the next iteration of the OMP algorithm. Simulation results show that the proposed algorithms outperform the conventional OMP algorithm in the MU-SM system.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2015.07a
• /
• pp.444-446
• /
• 2015

컴퓨터 생성 홀로그램(CGH: computer generated hologram) 기법은 기존의 홀로그램의 광학적 장치의 단점을 보완하여 범용 컴퓨터에서 홀로그램을 생성할 수 있도록 하는 기술이다. CGH는 입력으로 주어지는 물체의 3차원 정보와 출력으로 나오는 디지털 홀로그램의 해상도에 따라 그 연산량이 결정 된다. CGH는 단순하고 반복적인 수학적 계산을 통하여 디지털 홀로그램을 생성하게 되는데, 기존의 연구들에서는 GPU(graphic processing unit)를 이용하여 알고리즘들을 병렬적으로 처리한다. 본 논문에서는 기존연구에서 쓰인 GPU를 이용한 CGH을 개선하여 GPU가 장착되지 않은 상용 컴퓨터에서 GPU가 장착된 다른 컴퓨터들의 연산 자원을 활용하여 CGH를 수행 할 수 있는 프로그램의 개발 방법을 제안 한다. 본 시스템은 GPU가 요구되지 않는 한 개의 서버 컴퓨터와 GPU가 장착된 다수의 클라이언트들로 구성되어 있다. 서버 측에서 물체의 3차원 정보를 입력 받아 각각의 클라이언트들에게 적절한 연산량을 분배하고, 각 클라이언트들은 이미 알려진 GPU 기반 CGH를 통하여 연산을 수행 한 뒤, 그 결과를 서버로 다시 전송하게 된다. 서버는 수신한 각 결과들을 누적하여 입력 받은 물체에 대한 하나의 온전한 홀로그램을 생성할 수 있게 된다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.13 no.2
• /
• pp.160-170
• /
• 1988

This paper describes the outboard NIU(Network Interface Unit) using microprocessor and the hardware and software of concentrator for constructing star typed LAN(Local Area Network) based on token ring method. The NIU adapter can adapter up to four parallel and serial typed terminals. Because it has PAD function on input output data, any type of terminals can be adapted. Since the concentrator has logical switching circuit which enables data to bypass the faulted NIU adapter, this network prevents communication break. When user transmits and receives data, the concentrator constructs star typed LAN which connct both transmitting and receiving sides. A s result, this network eliminated ring latency time in other NIU exculding transmitting and receiving NIU. So the throughput of this LAN is increased. Because this LAN system consists of several modultes according to it's function, the expansion of function or the modification of method is easy.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.2
• /
• pp.102-106
• /
• 2008

A new compact UWB bandpass filter with sharp-rejection, low insertion-loss and flat group-delay is developed In this paper, using the transversal filtering combined with SIR(stepped impedance resonator) concept. To form the required passband, multiple out-of-band transmission zeros are created around band-edges, securing very low insertion loss in the very wide frequency range. Also it is found to be beneficial to realize a sharp rejection of higher order with a relatively small overall size and simultaneously have very smoothly varying group-delay which is proper for the UWB applications. The validity of the proposed technique is proven theoretically and experimentally.

• Nuclear Medicine and Molecular Imaging
• /
• v.43 no.5
• /
• pp.459-467
• /
• 2009

Purpose: The maximum likelihood-expectation maximization (ML-EM) is the statistical reconstruction algorithm derived from probabilistic model of the emission and detection processes. Although the ML-EM has many advantages in accuracy and utility, the use of the ML-EM is limited due to the computational burden of iterating processing on a CPU (central processing unit). In this study, we developed a parallel computing technique on GPU (graphic processing unit) for ML-EM algorithm. Materials and Methods: Using Geforce 9800 GTX+ graphic card and CUDA (compute unified device architecture) the projection and backprojection in ML-EM algorithm were parallelized by NVIDIA's technology. The time delay on computations for projection, errors between measured and estimated data and backprojection in an iteration were measured. Total time included the latency in data transmission between RAM and GPU memory. Results: The total computation time of the CPU- and GPU-based ML-EM with 32 iterations were 3.83 and 0.26 see, respectively. In this case, the computing speed was improved about 15 times on GPU. When the number of iterations increased into 1024, the CPU- and GPU-based computing took totally 18 min and 8 see, respectively. The improvement was about 135 times and was caused by delay on CPU-based computing after certain iterations. On the other hand, the GPU-based computation provided very small variation on time delay per iteration due to use of shared memory. Conclusion: The GPU-based parallel computation for ML-EM improved significantly the computing speed and stability. The developed GPU-based ML-EM algorithm could be easily modified for some other imaging geometries.