• 한국ITS학회:학술대회논문집
• /
• 2008.11a
• /
• pp.607-610
• /
• 2008

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.2
• /
• pp.45-49
• /
• 2009

In this paper, a direct down conversion LNA/Mixer has been designed and tested for 900Mhz UHF RFID application. The designed circuit has been implemented in 0.18um CMOS technology with 3.3V operation. In this work, a common gate input architecture has been used to cope with the higher input self jamming level. This LNA/Mixer is designed to support two operating modes of high gain mode and low gain mode according to the input jamming levels. The measured results show that the input referred P1dBs are 4dBm of high gain mode and 11dBm of low gain mode, and the conversion gains are 12dB and 3dB in high and low gain mode respectively The power consumptions are 60mW for high gain mode and 79mW for low gain mode. The noise figures are 16dB and 20dB in high gain mode and low gain mode respectively.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.11
• /
• pp.101-106
• /
• 2014

This paper presents a wide dynamic range radio-frequency (RF) root-mean-square (RMS) power detector using an automatic gain control (AGC) loop. The AGC loop consists of a variable gain amplifier (VGA), RMS conversion block and gain control block. The VGA exploits dB-linear gain characteristic of the cascade VGA. The proposed circuit utilizes full-wave squaring and generates a DC voltage proportional to the RMS of an input RF signal. The proposed RMS power detector operates from 500MHz to 5GHz. The detecting input signal range is from 0 dBm to -70 dBm or more with a conversion gain of -4.53 mV/dBm. The proposed RMS power detector is designed in a 65-nm 1.2-V CMOS process, and dissipates a power of 5 mW. The total active area is $0.0097mm^2$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.3
• /
• pp.1685-1690
• /
• 2014

This paper proposes a novel method to compensate for the measurement errors in detecting phase currents for vector-controlled inverter in real-time. The output torque equations for 3-phase induction motor are derived in terms of offset error and transducing gain error in current measurement circuits, and the equations shows that motor output torque has many ripples due to current measurement errors. Especially, if the proposed method is applied to vector-controlled inverter, the torque ripple by transducing gain error can be reduced in real-time at running state of motor. To verify the proposed method, it was applied to vector-controlled inverter for 3-phase induction motor of 200[W] and computer simulation and experimentation were carried out.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 1997.11a
• /
• pp.55-62
• /
• 1997

본 논문에서는 윤곽선의 다각근사화시 발생하는 오차신호를 표본화하고 표본화된 신호를 부호화하기 위한 새로운 변환을 제안한다. 제안하는 방법은 다각근사화시 발생하는 윤곽선의 단편들이 완만한 곡선의 형태를 갖고 양 끝점이 0이라는 특징을 고려해서 르장드르 다항식에 기반한 새로운 변환을 제안한다. 제안한 방법은, 기존의 방법인 이산여현변환, 이산정현변환 등과 변환부호화 이득면에서 비교해 볼 때 우수한 결과를 얻었다.

• Journal of Korea Multimedia Society
• /
• v.6 no.7
• /
• pp.1159-1168
• /
• 2003

In this paper, a new wavelet filter design algorithm is proposed which optimizes energy compaction of transformed coefficients. The filter, designed by the proposed algorithm enhances the coding gain of the system with fixed quantizer by most unevenly distributed energy in transform domain. The coding gain function was extended to obtain the optimal filter coefficients in each stage. The experiments showed that the filter designed by proposed method outperforms conventional filters in energy compaction rate.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.10a
• /
• pp.411-415
• /
• 2003

In this paper, a reflector type frequency doubler for local oscillator at 24GHz is designed and fabricated with ne71300-N MESFET. Optimum source and load impedances are decided through a multiharmonic load pull simulation technique. A conversion gain ran be improved using the reflector and fundamental and third harmonics are well suppressed with open stub of λ/4 length. Measured results show output power at 0dBm of input power is -3.776dBm, conversion gain 0.736dB, harmonic suppression 41.064dBc, respectively.

• Journal of Navigation and Port Research
• /
• v.28 no.1
• /
• pp.37-41
• /
• 2004

In this paper, a reflector type frequency doubler for local oscillator at 24GHz is designed and fabricated with ne71300-N MESFET. Optimum source and load impedances are decided through a multiharmonic load pull simulation technique. A conversion gain can be improved using the reflector and fundamental and third harmonics are well suppressed with open stub of $\lambda$/4 length Measured results show output power at 0dBm of input power is -3.776dBm, conversion gain 0.736dB, harmonic suppression 41.064dBc, respectively.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2008.05a
• /
• pp.698-701
• /
• 2008

본 논문에서는 상용소자의 특성과 상향변환기의 모듈에 소요되는 링크전력을 비교 분석하여 Ka-band VSAT UPCONVERTER를 설계하였다. $30GHz{\sim}31GHz$대역에서 2W 출력신호를 나타내기 위하여 상향변환시스템은 IF증폭단, 감쇄기, 믹서단, 대역통과필터 및 2W 전력증폭단으로 구성시켰으며 상용MMIC를 이용하여 설계된 상향변환모듈은 $6.29dBm{\sim}7.88dBm$의 출력전력, 이득은 $23.19{\sim}28.15dB$을 Cain flatness는 4.95dB를 나타내었다. 최종단의 전력증폭기는 $33.75{\sim}34.96dBm$의 출력전력을 나타내었으며 이득은 $38.5{\sim}41.98dB$로 측정되었다.

• The Journal of the Korea Contents Association
• /
• v.6 no.4
• /
• pp.1-10
• /
• 2006

In this paper, a broadband RF module is designed and tested for 2.4GHz band applications. The RF module is composed of a low noise amplifier (LNA) with a three stage amplifier, a single ended gate mixer, matching circuits, a hairpin line band pass filter and a Chebyshev low pass filter to convert the radio frequency (RF) into the intermediate frequency (IF). The LNA has a high gain and stability, and the single ended gate mixer has a high conversion gain and wide dynamic range. In the analysis of the broadband RF module, the composite harmonic balance technique is used to analyze the operating characteristics of an RF module circuit. The RF module has a 55.2dB conversion gain with a 1.54dB low noise figure, $-120{\sim}-60dBm$ wide RF power dynamic range, -60dBm low harmonic spectrum and a good isolation factor among the RF, IF, and local oscillator (LO) ports.