• Journal of the Korean Vacuum Society
• /
• v.21 no.1
• /
• pp.29-35
• /
• 2012

The Hydrogenated silicon nitride (SiNx:H) using plasma enhanced chemical vapor deposition is widely used in photovoltaic industry as an antireflection coating and passivation layer. In the high temperature firing process, the $SiN_x:H$ film should not change the properties for its use as high quality surface layer in crystalline silicon solar cells. Initially PECVD-$SiN_x:H$ film trends were investigated by varying the deposition parameters (temperature, electrode gap, RF power, gas flow rate etc.) to optimize the process parameter conditions. Then by varying gas ratios ($NH_3/SiH_4$), the hydrogenated silicon nitride films were analyzed for its optical, electrical, chemical and surface passivation properties. The $SiN_x:H$ films of refractive indices 1.90~2.20 were obtained. The film deposited with the gas ratio of 3.6 (Refractive index=1.98) showed the best properties in after firing process condition. The single crystalline silicon solar cells fabricated according to optimized gas ratio (R=3.6) condition on large area substrate of size $156{\times}156mm$ (Pseudo square) was found to have the conversion efficiency as high as 17.2%. Optimized hydrogenated silicon nitride surface layer and high efficiency crystalline silicon solar cells fabrication sequence has also been explained in this study.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.41 no.6
• /
• pp.81-89
• /
• 2004

In this paper, we compare face recognition rate by PCA algorithm using distance change and embedded data being input left side and right side image in stereo images. The proposed method detects face region from RGB color space to YCbCr color space. Also, The extracted face image's scale up/down according to distance change and extracts more robust face region. The proposed method through an experiment could establish standard distance (100cm) in distance about 30∼200cm, and get 99.05% (100cm) as an average recognition result by scale change. The definition of super state is specification region in normalized size (92${\times}$112), and the embedded data extracts the inner factor of defined super state, achieved face recognition through PCA algorithm. The orignal images can receive specification data in limited image's size (92${\times}$112) because embedded data to do learning not that do all learning, in image of 92${\times}$112 size averagely 99.05%, shows face recognition rate of test 1 99.05%, test 2 98.93%, test 3 98.54%, test 4 97.85%. Therefore, the proposed method through an experiment showed that if apply distance change rate could get high recognition rate, and the processing speed improved as well as reduce face information.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.6A
• /
• pp.618-627
• /
• 2002

In processing images using 2 dimensional Discrete Wavelet Transform(2D-DWT), the method to process the pixels around the image boundary may affect the quality of image and the cost to implement in hardware and software. This paper proposed an effective method to treat the boundary pixels, which is apt to implement in hardware and software without losing the quality of the image costly. This method processes the 2-D image as 1-D array so that 2-D DWT is performed by considering the image with the serial-sequential data structure (Serial-Sequential Processing). To show the performance and easiness in implementation of the proposed method, an image compression codec which compresses image and reconstructs it has been implemented and experimented. It included log-scale fried quantizer, but the entropy coder was not implemented. From the experimental results, the proposed method showed the SNR of almost the same SNR(Signal to Noise Ratio) to the Periodic Expansion(PE) method when the compression ratio(excluding entropy coding) of 2:1, 15.3% higher than Symmetric Expansion(SE) method, and 9.3% higher than 0-pixel Padding Expansion(ZPE) method. Also PE method needed 12.99% more memory space than the proposed method. By considering only the compression process, SE and ZPE methods needed additional operations than the proposed one. In hardware implementation, the proposed method in this paper had 5.92% of overall circuit as the control circuit, while SE, PE, and ZPE method has 22%, 21,2%, and 11.9% as the control circuit, respectively. Consequently, the proposed method can be thought more effective in implementing software and hardware without losing any image quality in the usual image processing applications.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.307-307
• /
• 2010

최근 유한연료의 고갈로 인해 세계 유가가 불안정 됨으로서 대체 에너지에 대한 연구가 많이 진행 되고 있다. 특히 압전 소자를 이용한 에너지 하베스팅은 압전 역효과를 이용한 것으로서 주변에서 무의미하게 버려지는 진동이나 바람, 열 에너지를 실 생활에 사용할 수 있는 전기 에너지로 변환할 수 있는 유망한 기술 중 하나이다. 이러한 에너지 하베스팅 기술은 일본과 같은 선진국에서 이미 지하철 및 일반 다리와 같이 진동이 극히 많은 곳에서 응용되고 있다. 이러한 에너지 하베스팅 기술을 응용 하려면 전압출력 계수($g_{33}$)가 높아야 한다. 이것은 압전 d 상수와 유전상수에 영향을 많이 받는 것으로 알려져 있다. 현재가지 응용되는 압전 하베스팅 조성은 Pb(Zr,Ti)$O_3$ (PZT)를 기초로한 세라믹이 응용되고 있다. Pb(Zr,Ti)$O_3$ (PZT) 세라믹은 Morpohotropic phase boundary(MPB)에서 전기기계 결합계수 (kp) 와 기계적 품질계수 (Qm) 이 각각 0.5와 500으로 우수한 특성을 나타낸다. 또한 큐리온도 (Tc) 도 $400^{\circ}C$로 온도 안정성 또한 높다. 하지만 $1000^{\circ}C$ 이상에서 소결하는 PbO는 소결 중 급격한 휘발로 환경적 오염 뿐 아니라 특성의 저하를 야기시킨다. 그래서 몇몇 나라에서는 그 사용을 제한하고 점차적으로 사용을 줄여 나가고 있는 동시에 PbO가 첨가되어 있지 않은 Lead-Free 세라믹의 연구가 많이 진행되고 있다. Lead-Free 세라믹 중 alkaline niobate를 기초로 한 페로브스카이트 구조의 ($Na_{0.5}K_{0.5})NbO_3$ (NKN) 은 PbO를 기초로 한 세라믹을 대체할 유망한 후보자 중 하나이다. 하지만 NKN세라믹의 K 성분의 조해성 및 고온에서의 휘발로 인해 일반 적인 소결 방법으로는 고밀도의 세라믹을 얻기 매우 어렵다. 그래서 Hot pressing, Hot forging, RTGG(Reactive Template Grain Growth), SPS(Spark plasma Sintering)와 같은 특별한 소결 법을 이용하거나 $K_8CuNb_4O_{23}$(KCN) 이나 $K_{5.4}Cu_{1.3}Ta_{10}O_{29}$(KCT) 등을 첨가하여 그 소결성을 향상 시키는 방법도 있다. 또한 압전 d상수를 향상 시키기 위해 $Nb_2O_5$나, $La_2CO_3$, $CeO_2$, $Li_2CO_3$ 등을 치환함으로써 압전 d상수를 향상 시켜 전압출력 계수를 높이는 연구 또한 많은 보고가 되어 있다. 특히 $Li_2CO_3$의 첨가는 일반 적인 소결 방법으로도 밀도의 조밀함을 향상 시켜 그에 따른 높은 유전율과 전기기계 결합계수, 압전 d상수를 가져 많은 연구가 되어지고 있다. 그래서 본 연구에서는 일반적인 ($K_{0.5}N_{0.5})_{1-x}Li_x(Nb_{0.96}Sb_{0.04})O_3$ + 0.2mol%$La_2O_3$ + 1.2mol%$K_8CuNb_4O_{23}$ 세라믹에 x(=Li) 치환에 따른 유전 및 압전특성을 조사하였다.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.10
• /
• pp.1169-1176
• /
• 2010

The RF front-end for L1/L2 dual-band Global Positioning System(GPS) receiver is presented in this paper. The RF front-end(down-converter) using low IF architecture consists of a wideband low noise amplifier(LNA), a current mode logic(CML) frequency divider and a I/Q down-conversion mixer with a poly-phase filter for image rejection. The current bleeding technique is used in the LNA and mixer to obtain the high gain and solve the head-room problem. The common drain feedback is adopted for low noise amplifier to achieve the wideband input matching without inductors. The fabricated RF front-end using $0.18{\mu}m$ CMOS process shows a gain of 38 dB for L1 and 41 dB for L2 band. The measured IIP3 is -29 dBm in L1 band and -33 dBm in L2 band, The input return loss is less than -10 dB from 50 MHz to 3 GHz. The measured noise figure(NF) is 3.81 dB for L1 band and 3.71 dB for L2 band. The image rejection ratio is 36.5 dB. The chip size of RF front end is $1.2{\times}1.35mm^2$.

• Journal of Life Science
• /
• v.30 no.5
• /
• pp.420-427
• /
• 2020

A repebody, an artificial non-immunoglobulin protein scaffold, is expected to be a solution in the search for faster, cheaper, and customizable antibodies. However, the production of medical repebodies remains difficult due to their low yield and the complex purification processes required. The Pseudomonas fluorescens ABC transporter system has been suggested as an efficient and cost-effective method for repebody production, but the total yield is low because of the secreted protein's positive charge; thus, a repebody with a high isoelectric point needs to be changed into a more negatively charged protein for better secretion. To achieve this, we first attached oligo-aspartic acids to the N- and C-terminals of the repebody, but secretion efficiency was not enhanced significantly. Subsequently, we devised an alternative method for improved secretion efficiency by engineering fifteen positively charged amino acids to aspartic acid in the non-antigen binding sites of the repebody to give a high net negative charge. As a result, secretion efficiency was greatly enhanced from 21.2% (wildtype) to 58.5% (negatively supercharged). The negatively supercharged repebody was succussfully produced extracellularly by ABC transporter secretion system in P. fluorescens.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.5
• /
• pp.465-471
• /
• 2013

A steam generator in nuclear power plant is a heatexchager which is used to convert water into steam from heat produced in a nuclear reactor core, and the steam produced in steam generator is delivered to the turbine to generate electricity. Because of damage to steam generator tubing may impair its ability to adequately perform required safety functions in terms of both structural integrity and leakage integrity, eddy current testing is periodically performed to evaluate the integrity of tubes in steam generator. This assessment is normally performed during a reactor refueling outage. Currently, the eddy current testing for steam generator of nuclear power plant in Korea is performed in accordance with KEPIC & ASME Code requirements, the eddy current testing system is consists of remote data acquisition unit and data analysis program to evaluate the acquired data. The KEPIC & ASME Code require that the electrical properties of remote data acquisition unit, such as total harmonic distortion, input & output impedance, amplifier linearity & stability, phase linearity, bandwidth & demodulation filter response, analog-to-digital conversion, and channel crosstalk shall be measured in accordance with the KEPIC & ASME Code requirements. In this paper, the measurement requirements of electrical properties for eddy current testing instrument described in KEPIC & ASME Code are presented, and the measurement results of newly developed eddy current testing instrument by KHNP(Korea Hydro & Nuclear Power Co., LTD) are presented.

• Proceedings of KOSOMES biannual meeting
• /
• 2007.11a
• /
• pp.97-102
• /
• 2007

The piggery wastewater is the major source of the water pollution problem in the rural area. The treatment alternatives for piggery wastewater are limited by the characteristics of both high organic and nitrogen(N) content. In order to investigate an efficient N removal system, the thermophilic aerobic digestion process was examined. The experiment was investigated organic and nitrogen removal efficiency at various HRTs and air supply volume. The results of semi-continuous experiment indicated that a higher removal of the soluble portion of COD was achieved with the longer HRTs. However, the inert portion of COD in piggery wastewater was not much changed by thermophilic aerobic digestion. In addition, with the higher HRT of 3 days, up to 79% of NH4-N removal efficiency was achieved. Lower the HRTs, a decrease of NH4-N removal was founds. The gas samples from the lab reactor were analyzed along with the N content in influent and effluent. The N2O formation in our system indicates a novel aerobic deammonification process occurred during the thermophilic aerobic digestion. Both N02 and N03 were not presented in the effluent of thermophilic aerobic digester. With the HRT of 3 days, 36.4% of influent N(or 57.5% removal N) was aerobically converted to N2O gas. The ammonium conversion to N2O gas significantly decrease to 4.5% at low HRT of .05 day..

• Economic and Environmental Geology
• /
• v.24 no.4
• /
• pp.421-434
• /
• 1991

Ground magnetic surveys were conducted at four areas where the Yangsan fault, the most prominent lineament in the Kyeongsang basin, appears to be passed through. For data processing, IGRF correction, upward continuation and reduction-to-the-pole were performed. The automatic inversion by using a matrix computation method, which takes the depth to bottom layer of the horizontal two layer structure as the model parameter, has been attempted to delineate the subsurface structure. Upward continuation of the surface magnetic map to the same level of the aeromagnetic survey (KIER, 1989) resulted in very similiar patterns to those of aeromagnetic data. Subsurface modeling of eight profile data show that the strike and dip of the Yangsan fault in study areas are $N6^{\circ}-15^{\circ}E$, and near vertical to somewhat eastward, repectively, despite of the local lithological contrast of each study area. It seems that the magnetic effect of faulting in the study area 1, which locates in the most northern part of the survey areas, is disturbed by that of igneous intrusion. At study area 2, the possibility of volcanic or igneous intrusion, which is 200-300 meters wide along the fault plane was presented. At study area 3, unlike other study areas, distinct fracture zone of 500-700 meters in width was revealed along the surface fault line. The andesitic rocks of the study area 4 have very high susceptibilities and the fault line on surface of this area was shifted about 500 meter eastward, as compared with the inferred fault line by the previous study.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1992.10a
• /
• pp.25-30
• /
• 1992

최근 전자계산기를 이용한 진동해석 방법이 눈부시게 발달하여, 일반 구조물 이나 기계 구조물 등의 동특성을 설계 단계에서 정도 높게 예측하는 것이 가능하게 되었다. 그러나 종래의 구조해석은 주어진 시스템의 동특성을 위한 것으로 얻어진 동특성으로부터 질량, 관성제원 및 스프링상수값 등의 설계상 수값을 규명하는 연구는 미미한 실정이다. 이것에 대한 해결방법으로 크게 해석적인 방법과 실험적인 방법으로의 접근이 있어 왔다. 해석적인 방법으로 유한요소해석에서 얻은 모드좌표를 물리좌표로 변환하는 방법으로 Guyan의 정축소와 같은 절점축소를 행하는 방법이 고찰되었다. 실험적인 방법으로 가 진실험에서 얻은 전달함수나 모드파라미터로부터 [M], [K] 행렬을 결정하는 연구가 있었지만 어떤것도 질량, 스프링상수 등의 설계상수를 완전히 규명하 지는 못하였다. 또한, 설계 단계에서 필요한 질량, 관성제원 또는 스프링상수 등의 최적한 값이나, 원하는 시스템특성을 얻을 수 있는 설계상수의 적정한 폭을 구하는 연구는 설계자의 경험과 반복된 시행착오에 의존하는 실정이다. 감도해석은 이러한 문제점을 개선하는 수단으로 설계변수에 대한 동특성의 변화율을 구하는 것이다. 감도해석을 수행하는 것은 어느 설계변수를 수정하 는 것이 주어진 동특성에 부합되는 지를 알려주고, 어느 것을 수정하는 것이 원하는 방향의 동특성변화에 가장 효과적인지를 알려주는 것이다. 따라서 감 도해석을 이용하여 설계의 최적화 프로그램을 만들수 있고, 이것은 설계자가 요구하는 동특성을 목적함수로 하여 주어진 구조물을 최적화하는 설계상수 값을 얻을 수 있게 한다. 본 논문에서는 강체모델의 동특성으로부터 모델의 설계 상수를 규명하고, 동특성의 개선을 위하여 설계변수의 변경량을 물리좌 표계에서 얻는것을 목적으로 한다. 강체 마운트계의 관성제원 및 마운트강성 의 규명을 위하여 임으로 주어진 설계상수를 모델데이타로 하여 관성제원과 스프링 강성을 구하였다. 관성제원의 규명은 주어진 모델의 관성값을 모르는 것으로 하여 임의의 초기 관성값으로 감도해석에 의해 주어진 계의 관성값 을 물리 좌표계에서 규명하였다. 마운트 강성의 규명도 관성제원의 규명과 같은 방법으로 임의의 강성값으로 감도해석을 하여 강성값을 규명하였다. 또 한 감도해석에 의한 동특성 변경은 특정한 고유진동 수의 변경이 필요할 때, 고유진동수의 이동을 위한 관성제원의 변경 및 마운트 강성변경값을 예측할 수 있다. 본 연구수행의 기본적인 흐름도는 Fig.1.1과 같다. 위와 같은 작업 으로 엔진 마운트와 같은 강체 모델의 시스템 규명을 행하는 경우에 유한요 소해석 및 가진 실험으로 얻은 고유진동수의 정보 또는 원하는 고유진동수 의 특성을 기본으로 실제 설계에서 사용이 가능하도록 물리 좌표계에서 관 성 제원 및 스프링상수를 구할 수 있을 것이다.