• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.91.1-91.1
• /
• 2012

그래핀의 우수한 기계적 물성에 관한 연구가 보고된 이후 그래핀의 기계적 특성을 이용한 다양한 어플리케이션에 관한 연구가 진행되고 있다. 기계적 특성을 이용한 다양한 어플리케이션 중 가장 대표적인 것은 발생한 스트레인을 측정하는 스트레인 게이지일 것이다. 때문에 본 연구에서는 다양한 기계적 활용 방안 중 스트레인 게이지를 목표로 그래핀을 이용한 스트레인 게이지의 가능성에 관한 실험을 진행하였다. 먼저 그래핀 내에서의 Piezo-resistive 효과에 관한 기초 테스트를 진행을 통해 그래핀의 gauge factor 수치가 2.5가량이 나옴을 확인하였다. 이 때 사용된 그래핀의 경우 Ni 촉매층을 이용하여 CVD 장비를 이용하여 사용되었고 7%의 투과도를 보였다. 추가적으로 이 같은 그래핀의 Piezo-resistive 특성을 이용하여 우리는 두 종류의 변형률 센서를 제작하였다. 한 가지는 기존의 단일 게이지의 경우 미리 지정된 방향의 변형률 정도만을 측정할 수 있다는 단점을 극복하기 위한 rosette 형태의 스트레인 게이지를 제작함으로써 변형률 뿐만 아니라 표면에서 발생하는 주변형률의 방향을 측정할 수 있었다. 또한 제작된 스트레인 센서를 장갑위에 부착 함으로써 다가올 입는 형태의 전사소자에 응용이 가능한 모양의 변형률 센서 제작에 성공하였다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.40 no.4
• /
• pp.363-370
• /
• 2020

This paper reports the results of an experimental study using the BOTDR sensor to detect the unbonded location of attached CFRP sheet for structural rehabilitation. A specimens with the unattached CFRP sheet were fabricated for this study, on which BOTDR sensor was attached with a nylon net. During the flexural test of the specimens, the strain of the CFRP sheet was measured using the BOTDR sensor and electric resistance gauges. From the results, it was confirmed that the strain distribution obtained through the BOTDR sensor can be effectively used to visualize and detect the unbonded position of the CFRP sheet. In addition, In addition, the strain measured by the BOTDR sensor was found to be more effective in analyzing the overall structure behavior than the electric resistance strain gauge. The development of a BOTDR sensor with a measuring longth of less than 100 mm will enable accurate detection of the local unbonded position of the CFRP sheet.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.1
• /
• pp.49-55
• /
• 2002

In this paper, we present the simulation monitoring of strain and temperature during and after the cure of unsymmetric composite laminate using fiber optic sensors. Fiber Bragg grating/extrinsic Fabry-Perot interferometric (FBG/EFPI) hybrid sensors are used to measure those measurands. The characteristic matrix of the sensor is analytically derived and measurements can be done without sensor calibration. A wavelength-swept fiber laser is utilised as a lighr source. Two FBG/EFPI sensors are embedded in a graphite/epoxy unsymmetric cross-ply composite laminate in different directions and different locations. We perform a real time monitoring of fabrication strains and temperatures at two points of the composite laminate during cure process in an autoclave. Also, the thermal strains and temperatures of the fabricated laminate are measured in a thermal chamber. Through these experiments, we can provide a basis for the efficient smart processing of composite and know the thermal behavior of unsymmetric cross-ply composite laminate.

• Explosives and Blasting
• /
• v.35 no.3
• /
• pp.15-20
• /
• 2017

In order to obtain the dynamic response behavior of the rock subjected to blasting loading, a shock-proof high sensitivity impact sensor which can measure high frequency dynamic force and strain events should be adopted. Because the impact sensors which uses quartz and piezoelectric element are costly, generally the strain measurement-based impact (SMI) sensors are applied to high speed loading devices. In this study, dynamic Brazilian tension tests of granitic rocks was conducted using the Nonex Rock Cracker (NRC) reaction driven-high speed loading device which adopts SMI sensors. The dynamic response of the granite specimens were monitored and the intermediate strain rate dependency of Brazilian tensile strengths was discussed.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.6 no.3 s.22
• /
• pp.9-16
• /
• 2006

In structural health monitoring, the safety of structural members are assessed by the level of stress measured by various strain sensors based on different sensing mechanisms. Since most existing strain sensors used for health monitoring system can cover a relatively small range of structural members, it is very difficult to measure the maximum value of the member subjected to varying amount and types of loads with those point sensors. The reliability of assessed safety of a member may be improved by increasing the number of sensors. It may not be also realistic to increase the number of sensors to overcome these drawbacks. In this paper, a stress measuring method for beam-column members is developed by estimating the maximum stress based on the average strains obtained from long gauge sensor. The average strain from long gage fiber optic sensor is transformed into the maximum strain by multiplication of the modification factor derived in this research.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.7
• /
• pp.43-50
• /
• 2004

For the simultaneous measurement of strain and damage signal a fiber Bragg grating sensor system with a dual demodulator was proposed. The dual demodulator is composed of a demodulator using a tunable Fabry-Perot filter measuring the low-frequency signal with large magnitude such as strain and the other using a passive Mach-Zehnder interferometer detecting the high-frequency signal with small amplitude such as impact or damage signal. Using the proposed fiber Bragg grating sensor system, both the strain and damage signals of a cross-ply laminated composite beam under tensile loading were simultaneously measured. The strain and damage signals detected by single fiber Bragg grating sensor showed that sudden strain shifts were accompanied with vibration at a maximum frequency of several hundreds of kilohertz at the instant of matrix crack propagation in the 90 degree layer in composite beam.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.40 no.6
• /
• pp.547-553
• /
• 2020

As aging infrastructures increase along with time, the efficient maintenance becomes more significant and accurate responses from the sensors are pre-requisite. Among various responses, strain is commonly used to detect damage such as crack and fatigue. Optical fiber sensor is one of the promising sensing techniques to measure strains with high-durability, immunity for electrical noise, long transmission distance. Fiber Bragg Grating (FBG) is a point sensor to measure the strain based on reflected signals from the grating, while Brillouin Optic Correlation Domain Analysis (BOCDA) is a distributed sensor to measure the strain along with the optical fiber based on scattering signals. Although the FBG provides the signal with high accuracy and reproducibility, the number of sensing points is limited. On the other hand, the BOCDA can measure a quasi-continuous strain along with the optical fiber. However, the measured signals from BOCDA have low accuracy and reproducibility. This paper proposed a multi-fidelity data-fusion method based on Gaussian Process Regression to improve the fidelity of the strain distribution by fusing the advantages of both systems. The proposed method was evaluated by laboratory test. The result shows that the proposed method is promising to improve the fidelity of the strain.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.1
• /
• pp.44-48
• /
• 2002

In this paper, we demonstrated the simultaneous measurment of triple parameters such as strain, temperature, and vibration using single FBG/EFPI hybrid sensor. The FBG/EFPI sensor system for the strain and temperature measurement and the EFPI sensor system for the the vibration measurement were combined by a wavelength division multiplexer. The optical source of FBG/ EFPI sensor system is a wavelength-swept fiber laser(WSFL) and that of an EFPI sensor system is a laser diode. We performed the simultaneous measurement of thermal strain, temperature, and vibration of a aluminum beam placed in a thermal chamber and validated the efficiency of the constructed measurment system.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2006.06a
• /
• pp.275-276
• /
• 2006

선박 및 해양기자재의 안전 진단을 위한 기존의 기술은 접 센서(point sensor)를 이용한 변형률 측정 기술이 대부분이라 할 수 있다. 본 논문은 기존의 기술보다 효율적으로 응용될 수 있는 광섬유 센서를 이용한 분포 개념의 온도 및 변형률 측정(DTSS: Distributed Temperature & Strain Sensing) 기술에 대해 소개하고 있다. 이 기술은 선체 응력 모니터링, 해양 구조물 안전진단, subsea flowline 모니터링, platform의 riser 안정성, umbilical 모니터링 등에 활용될 수 있다.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.04a
• /
• pp.95-102
• /
• 2004

For the simultaneous measurement of strain and damage signal, a fiber Bragg grating sensor system with a dual demodulator was proposed. One demodulator using a tunable Fabry-Perot filter can measure low-frequency signal such as strain and the other demodulator using a passive Mach-Zehnder interferometer can detect high-frequency signal such as damage signal or impact signal. Using a proposed fiber Bragg grating sensor system, both the strain and damage signal of a cross-ply laminated composite beam under tensile loading were simultaneously measured. Analysis of the strain and damage signals detected by single fiber Bragg grating sensor showed that sudden strain shifts were induced due to transverse crack propagation in the 90 degree layer of composite beam and vibration with a maximum frequency of several hundreds of kilohertz was generated.