본 논문에서는 이차 본딩으로 접착된 복합재료-복합재료 Single-Lap 조인트 시편에 대해 인장 시험 및 수치해석을 통해 그 파손 특성을 조사하였다. 시편시험에서는 시험 중에 CCD 카메라 및 AE 센서를 이용해 초기 균열의 발생 및 진전양상에 대한 시험적인 관찰을 수행하였다. 시편에 대해 기하비선형 유한요소해석 및 VCCT(Virtual Crack Closure Technique)기법을 이용해 시편의 거동 및 변형율에너지방출률을 계산하고 세 가지 관찰된 초기 균열 모드에 대해 파손강도를 계산하였다. 인장시험에서 초기 균열은 모서리 계면 균열, 측면 계면 균열 및 층간 분리 균열의 세 가지 형태로 최종 파손의 60∼90% 하중에서 발생하였다. 주된 파손 모드는 접착제 계면 파손(adhesive failure) 및 적층판의 첫 번째 및 두 번째의 층간 분리 파손이었다. 두꺼운 접착제 층을 갖는 시편들은 초기균열이 낮은 하중에서 발생하였지만 균열진전에 대한 저항성 및 파손하중은 높게 나타났다. 층간분리파손은 주로 두꺼운 접착제의 경우에 발생하였다. 세 가지 초기 균열 모드에 대해 변형률에너지방출률은 Mode I의 G값이 Mode II의 G값보다 크게 계산되었다. Mode I 및 전체 G값은 측면 계면 균열, 모서리 계면 균열, 층간분리 균열의 순서로 크게 계산되었다.
Unidirectional commingled-yarn-based carbon fiber(CF)/polyamide(PA) 6 composite was fabricated under molding pressures of 0.4, 0.6 and 1.0 MPa to study its flexural deformation and fracture behavior. Fiber/matrix interfacial bonding area became larger with an increase of molding pressure from 0.4 to 0.6 MPa. For molding pressures .geq. 0.6 MPa, good flexural performance of similar magnitudes was attained. For the fracture test, four kinds of notch direction were adopted : edgewise notches parallel (L) and transverse (T) to the major direction of fiber bundles, and flatwise notches parallel(ZL) and perpendicular(ZT) to this direction. Nominal bend strength for L and ZL specimens exhibited high sensitivity to notching. ZL specimens revealed the lowest values of the critical stress intensity factor $K_c$ which was slightly superior to those of unfilled PA6 matrix. Enlargement of the compression area for T specimens was analyzed by means of the rigidity reduction resulting from the fracture occurrence.
Renewable energy sources such as wind energy is copiously available without any limitation. Wind turbines are used to tap the potential of wind energy which is available in millions of megawatt. Reliability of wind turbine is critical to extract this maximum amount of energy from the wind. We reviewed different techniques, methodologies, and algorithms developed to monitor the performance of wind turbine as well as for an early fault detection to keep away the wind turbines from catastrophic conditions due to sudden breakdowns. To keep the wind turbine in operation, implementation of Condition Monitoring System (CMS) is paramount, and for this purpose ample knowledge of these types of system is mandatory. So, an attempt has been made in this direction to review maximum approaches related to CMS in this piece of writing.
A semi-infinite parallel crack propagated with constant velocity in two bonded anisotropic strip under anti-plane clamped displacement is analyzed. Using Fourier integral transform a Wiener-Hopf equation is derived. By solving this equation the asymptotic stress and displacement fields near the crack tip are determined, where the results give the more general expression applicable to the extent of the anisotropic material having one plane of elastic symmetry for the parallel crack. The dynamic stress intensity factor and energy release rate are also obtained as a closed form, which are the results applicable to the problem both of dynamic and static crack under the same geometry as this study. The stress intensity factor approaches zero at the critical crack velocity which is less than the shear wave velocity, but in typical case of isotropic or orthotropic material agrees with the velocity of shear wave. Also a circular shear stress around crack tip is considered, from which the stress is shown to be approximately symmetric about the horizontal axis. Referring to the maximum stress criteria, it could be shown that a brenched crack is formed by crack growth as crack velocity increases.
A semi-infinite interfacial crack propagated with constant velocity in two bonded anisotropic strips under out-of-plane clamped displacements is analyzed. Using Fourier integral transform the problem is formulated and the Wiener-Hopf equation is derived. By solving this equation the asymptotic stress and displacement fields near the crack tip are obtained, where the results get more general expressions applicable not only to isotropic/orthotropic materials but also to the extent of the anisotropic material having one plane of elastic symmetry for the interfacial crack. The dynamic stress intensity factor is obtained as a closed form, which is decreased as the velocity of crack propagation increases. The critical velocity where the stress intensity factor comes to zero is obtained, which agrees with the lower value between the critical values of parallel crack merged in the material 1 and 2 adjacent to the interface. Using the near tip fields of stresses and displacements, the dynamic energy release rate is also obtained as a form of the stress intensiy factor.
기존의 보행분석 연구들은 하지를 하나의 스프링으로 간주하였다. 만약 슬관절 신전을 보조할 수 있는 슬관절 액추에이팅 메커니즘을 개발할 수 있다면 보행에 필요한 탄성-변형률에너지를 혁신적으로 저장-방출할 수 있고, 그 결과 보행 중 하지강성은 더욱 증가할 것이다. 게다가 족관절 액추에이팅 메커니즘까지 추가되어 있다면 슬관절 액추에이터에 의한 과도한 인공하지강성을 능동적이고 적절한 수준으로 보상해주는 기전으로 작동할 것이다. 만약 가속도에 의한 보행속도 증가를 방지하기 위해 인위적 감속통제를 작동시킨다면 불필요한 운동에너지의 방출이 발생되고 하지강성 액추에이터의 실효성은 의심을 받게 된다. 따라서 본 저자는 보행속도를 2개의 세그먼트에 의한 상대 각속도 조절기법을 이용하여 하지강성을 증가시킨다는 기본개념으로 슬-족관절 액추에이터 시스템을 개발하였다. 또한 족관절에 슬관절 액추에이팅에 대한 보상기전이 존재하는 경우, 족관절의 보상기전이 중족지절관절 경사각 및 보행속도 변화에 미치는 상호영향을 연구하였다.
횡등방성 압전재료에 기하학적 비대칭인 쐐기균열문제를 해석하였다. 기계적 집중면외하중과 전기적 집중 면내하중이 쐐기표면 점에 작용하고 있고, 반면에 균열면 한점에는 기계적 집중하중만 작용한다. 균열면은 침투형 얇은 슬릿으로 가정하여, 전기변위의 수직성분 및 전위가 균열면을 가로질러 연속으로 두었다. Mellin 변환을 사용하여 문제를 수식화하고, Wiener-Hopf 식을 유도하였다. 이 식을 풀므로써 폐형으로 주어지는 해를 얻었다. 임의 균열길이나 경사각, 쐐기각에 대해서도 적용이 가능한 응력 및 전기변위 강도계수를 구하였다. 장의 강도계수들은 전기적 하중에는 무관하고, 전기변위강도계수는 응력강도계수만의 함수로 표현되었다. 전기장 강도계수는 영으로 계산되었다. 또한 에너지방출률을 얻었다. 이 해는 중첩에 의하여 임의로 분포하는 전기기계하중문제에 대한 해를 제공하는 기본해로 사용될 수 있다.
2001년 9.11테러로 인한 미국 세계무역센터 및 미국 국방성 펜타곤이 붕괴된 이후, 전 세계적으로 충돌, 폭발 등의 극한하중에 의한 테러가 빈번하게 발생하고 있으며, 극한하중에 의한 구조물의 거동에 대한 사회적 불안감은 더욱 증가되고 있다. 그러나 지금까지의 사회기반시설구조물에는 폭발 및 충돌 등과 같은 극한하중에 대한 방호 및 방재개념을 설계에 고려하지 못하고 있는 실정이며, 원전격납건물, 가스탱크, 교량, 터널 등에 널리 사용되는 프리스트레스트 콘크리트 구조물에 대한 극한하중 연구는 전 세계적으로 미흡하다. 충돌과 같은 극한하중은 집약된 에너지의 급작스런 방출로 인한 높은 충돌압력을 형성하므로, 극한하중의 특성 및 전파 메커니즘을 이해하는 것이 필요하다. 그러므로 이 연구에서는 이방향 비부착 프리스트레스트 콘크리트 패널의 충돌저항성능을 비교검토하기 위하여, $1400mm{\times}1000mm{\times}300mm$의 철근콘크리트(RC), 프리스트레스 텐던으로만 보강된 콘크리트(PS), 프리스트레스 텐던과 철근으로 보강된 콘크리트(PSR, 일반적인 PSC) 시편을 제작하였다. 실험 조건에 맞춰 14 kN의 추를 10 m, 5 m, 4 m 높이에서 낙하하는 예비 실험과 3.5 m 높이의 본 실험으로 구성하여 충돌하중에 대한 프리스트레스트 콘크리트 구조물의 실험적 평가를 수행하였다. 또한, 충돌실험을 위한 기본적인 실험 구성 및 계측시스템을 구축하였다. 충돌 저항성능은 균열형상, 손상면적, 에너지 흡수, 처짐, 변형률, 가속도 등의 충돌에 의한 계측데이터를 이용한 거동분석 뿐만 아니라, 충돌 후 잔류구조성능 실험을 수행하여 이방향 비부착 프리스트레스트 콘크리트 패널의 충돌저항성능을 검토하였다. 본 실험은 향후 국내외 프리스트레스트 콘크리트에 대한 충돌 방호설계 및 충돌해석 등 관련 연구분야의 기초자료가 될 것이라고 판단되는 바이다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.