• Journal of the Korean Geotechnical Society
• /
• v.24 no.12
• /
• pp.103-111
• /
• 2008

Soils naturally contain grains of different minerals which may be dissolved under chemical or physical processes. The dissolution leads changes in microstructure of particulate media, such as an increase in local void or permeability, which affects the strength and deformation of soils. This study focuses on the small strain stiffness characteristics of vanishing mixtures, which consist of sand and salt particles at different volume fractions. Experiments are carried out in a conventional oedometer cell (Ko-loading) integrated with bender elements for the measurement of shear waves. Dissolutions of particles are implemented by saturating the mixtures at various confining stresses. Axial deformation and shear waves are recorded after each loading stage and during dissolution process. Experimental results show that after dissolution, the vertical strain and the void ratio increase, while the shear wave velocity and small strain shear modulus decrease. The decrease of the velocity results from the void ratio increase and particle contact decrease. The process monitoring during dissolution of the particles shows that the vertical strain dramatically increases at the beginning of the saturation process and converges after vanishing process finishes, and that the shear wave velocity decreases at the beginning and increases due to the particle reorientation. Specimens prepared by sand and salt particles are proved to be able to provide a valuable insight in macro structural behaviors of the vanishings mixtures.

• Korean Journal of Optics and Photonics
• /
• v.34 no.3
• /
• pp.99-105
• /
• 2023

The performance of astronomical telescopes can be negatively affected by atmospheric turbulence. To address this issue, techniques for atmospheric turbulence correction have been developed, requiring the simulation of atmospheric turbulence in the laboratory. The most practical way to simulate atmospheric turbulence is to use a phase plate. When measuring a phase plate that simulates strong turbulence, a Shack-Hartmann wave-front sensor is commonly used. However, the laser power decreases as it passes through the phase plate, potentially leading to a weak laser signal at the sensor. This paper investigates the need to control the laser power when measuring a phase plate that simulates strong atmospheric turbulence, and examines the effects of the laser power on the measured wavefront. For phase plates with relatively high Fried parameter r₀, the laser power causes a variation of over 10% in r₀. For phase plates with relatively low r₀, the laser power causes a variation of less than 5%, which means that the influence of the laser power is negligible for phase plates that simulate strong atmospheric turbulence. Based on the system described in this paper, a phase plate simulating strong atmospheric turbulence can be measured at a laser power of 5 mW or higher. Therefore, controlling the laser's output power is necessary when measuring a phase plate for simulating atmospheric turbulence, especially for phase plates with low r₀ values.

• Journal of the Korean Chemical Society
• /
• v.67 no.2
• /
• pp.106-115
• /
• 2023

The purpose of this study was to investigate the errors in science inquiry research reports written by students who won the encouragement award at the National Science Fair, and analyze the frequency of error types by school levels. The framework for analysis was constructed based on the table of contents of the students' science inquiry research reports, and the reports were analyzed for errors in six stages: Research question/hypothesis, prior research, experimental procedure, results, conclusions, and references. The study identified several types of errors at each stage, such as unreasonable research questions and wrong hypotheses in the research question/hypothesis stage, and limited considerations under certain conditions and selection of inappropriate experimental instruments in the experimental procedure stage. The study found that the frequency ratio of experimental procedure error was the highest across all school levels, and the order of errors varied by school level. Frequency ratio of error types of school level was: in the elementary school students' reports, errors were analyzed in the order of experimental procedure (36.88%), prior research (17.02%), conclusions (16.31%), research question/hypothesis (13.48%); In the middle school students' reports, experimental procedure (42.86%), conclusions (20.00%), prior research (14.28%), results (11.43%), research question/hypothesis (10.01%); In the high school students' reports, experimental procedure (45.16%), research question/ hypothesis (16.13%), conclusions (16.13%), and prior research (11.83%). The findings could be used to guide teachers in helping students conduct scientific inquiry research or write reports.

• Journal of the Korean Geotechnical Society
• /
• v.25 no.2
• /
• pp.55-66
• /
• 2009

At the mudstone slope located on the roadside of the Seokri area in Donghae-myeon, Pohang, Gyeongsangbuk-do, this study was performed to analyze the effects of rainfall on the stability of slope through seepage analysis according to the precipitation type of the mudstone slope, referring to the actual case of slope failure. For this, precise geological survey, geophysical exploration and drilling survey for the slope where the failure occurred were performed and followed by analysis of detailed soil layer. For the section where failure surface located, the durability reduction of rocks was measured through slaking/swelling tests and the permeability was measured through in-situ permeability tests for each soil layer. In addition, the change of strength parameter and process of instability were analyzed by back analysis, using Talren 97 and Slope/W programs, in the slope. By applying different precipitation conditions to the geographical conditions of the slope that had actual failure records, the slope stability was analyzed by seepage analysis according to duration of rainfall and rise of groundwater level resulting from the flow of rainfall caused by development of geological structures and the slope surface condition.

• Journal of the Korean earth science society
• /
• v.44 no.1
• /
• pp.1-12
• /
• 2023

Oceanic wind waves have been recognized as one of the important indicators of global warming and climate change. It is necessary to study the spatial and temporal variability of significant wave height (SWH) and wave direction in the Yellow Sea and a part of the East China Sea, which is directly affected by the East Asian monsoon and climate change. In this study, the spatial and temporal variability including seasonal and interannual variability of SWH and wave direction in the Yellow Sea and East China Sea were analyzed using European Center for Medium-Range Weather Forecasts (ECMWF) Reanalysis 5 (ERA5) data. Prior to analyzing the variability of SWH and wave direction using the model reanalysis, the accuracy was verified through comparison with SWH and wave direction measurements from Ieodo Ocean Science Station (I-ORS). The mean SWH ranged from 0.3 to 1.6 m, and was higher in the south than in the north and higher in the center of the Yellow Sea than in the coast. The standard deviation of the SWH also showed a pattern similar to the mean. In the Yellow Sea, SWH and wave direction showed clear seasonal variability. SWH was generally highest in winter and lowest in late spring or early summer. Due to the influence of the monsoon, the wave direction propagated mainly to the south in winter and to the north in summer. The seasonal variability of SWH showed predominant interannual variability with strong variability of annual amplitudes due to the influence of typhoons in summer.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.27 no.1
• /
• pp.33-47
• /
• 2022

In this study, distribution of submarine sand ridges in the coastal waters of Korea was surveyed using multibeam echo sounder data, and the topographic characteristics of each region were identified. For this purpose, the DEM (Digital Elevation Model) data was generated using depth data obtained from the Yellow Sea and the South Sea by Korea Hydrographic and Oceanographic Agency, and then applied the TPI (Topographic Position Index) technique to precisely extract the boundary of the sand ridges. As a result, a total of 200 sand ridges distributed in the coastal waters were identified, and the characteristics of each region of the sedimentary sediments were analyzed by performing statistical analysis on the scale (width, length, perimeter, area, height) and shape (width/length ratio, height/width ratio, linear·branch type, exposure·non-exposure type). The results of this study are expected to be used not only for coastal navigational safety, but also for marine naming support, marine aggregate resource identification, and fisheries resource management.

• Nuclear Engineering and Technology
• /
• v.11 no.3
• /
• pp.203-212
• /
• 1979

The thermal decomposition of simulated Magnox highly active waste and of HARVEST feed slurries (SW and SG) which include tile glass forming chemicals has been studied. The waste and the slurries are almost completely calcined by 500-55$0^{\circ}C$. The colour of the solids from the slurries varies little until about 90$0^{\circ}C$ when it darkens considerably. The slurries begin to vitrify at this temperature and are completely vitrified at 1000-105$0^{\circ}C$. On the other hand. the sulphate impurity in SN slurry causes a yellow phase to separate above 75$0^{\circ}C$. The density of the intermediate solids is fairly low until 650$^{\circ}$-$700^{\circ}C$ is reached. This temperature seems to mark the onset of fluxing as tile density rises quickly to 2g/㎤ at 700$^{\circ}$ -80$0^{\circ}C$. The strengh of the solids decreases with temperature up to 50$0^{\circ}C$, and then rises as the solids begin to sinter. Below 50$0^{\circ}C$ the SN solids are the stronger. suggesting that the impurity renders this silica more reactive.

• Journal of Korean Society for Quality Management
• /
• v.50 no.1
• /
• pp.169-181
• /
• 2022

Purpose: This paper addresses a case study of developing a flame retardant wood-plastic composites (WPC) by adding tannic acid to the existing synthetic wood. The optimal mixing ratios of six components are explored to minimize the burning time using two mixture designs. Methods: In the preliminary experiment, six components are considered to find important components and their ranges. Seven D-optimal mixture design points are generated. Two points are removed for the balance of plastic components to be maintained, and the remaining five points are augmented with two basic compositions. Four components are selected to be considered in the main experiment. In the main experiment, pellets are extruded at the eight mixture design points. In-house testing of burning time is executed three times. Specimens made of pellets from two promising flame retardant compositions are sent to the accredited laboratories and tested. Results: The test results are as follows: 1) The best composition (Wood flour, Tannic acid, PE, Lubricant) = (25, 41, 10, 2) (wt%) shows the burning time of 1 second, which is 9-fold improvement compared to the the burning time of 9 seconds from the existing composition (58, 0, 10, 2) (wt%). 2) The second best composition (41, 25, 10, 2) (wt%) results in the burning time of 2 seconds. This composition is inferior to the best composition in terms of the flame retardancy, but more economical since it needs less tannic acid which is 100-fold expensive than the wood flour. Conclusion: Flame retardant compositions are found by adding tannic acid to the existing WPC employing optimal mixture designs. This case study will be helpful to practitioners who try to develop new products with additional physical properties with as small number of experimental trials as possible. Future research direction includes exploring conditions which satisfy both performance level and cost limitation simultaneously.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.42 no.2
• /
• pp.209-217
• /
• 2022

Lane management with a central variable lane(s) (or reversible lane) where the traffic flow is temporarily reversed in one or more lanes during peak periods has been evaluated as an effective strategy to alleviate congestion caused by tidal traffic flows. However, due to traffic safety issues, such a movable barrier system can be considered as an alternative to supplement the existing its operation facilities such as static and/or dynamic signs and special pavement markings. In addition, when combined with a bus exclusive lane strategy, its effectiveness could be greatly increased. The objective of this study is to propose a feasibility analysis procedure for operational strategies of a bus-exclusive lanes using a barrier transfer system (BTS) for urban expressways. To this end, a case study was conducted on two urban expressways on the west side of the Han River in Seoul. As a result, temporary operation during rush hour in the morning was found to be most effective. The results presented in this study are expected to serve as a basis for establishing bus-exclusive lane operation strategies using similar systems in the future.

• Annals of Clinical Microbiology
• /
• v.17 no.1
• /
• pp.23-27
• /
• 2014

Rapidly growing mycobacteria are ubiquitous in the environment and are increasingly being recognized as opportunistic pathogens. Recently, a new species, Mycobacteium conceptionense, has been validated from the Mycobacterium fortuitum third biovariant complex by molecular analysis. However, there are few reports, and postsurgical wound infection by this species is rare. We report a case of postsurgical wound infection caused by M. conceptionense in an immunocompetent patient that was identified by a sequencing analysis of 16S rRNA, hps65, and rpoB genes.