• Journal of Dental Rehabilitation and Applied Science
• /
• v.36 no.2
• /
• pp.95-103
• /
• 2020

Purpose: The purpose of this study was to compare the axial displacement of the hexagonal and conical abutment in internal conical connection implant after screw tightening and cyclic loading. Materials and Methods: Internal conical connection implants were divided into two groups (n = 10): group HEX, hexagonal abutment; and group CON, conical 2-piece abutments. The axial displacement and removal torque values were measured after 30 Ncm torque tightening and 250N loading test of 100,000 cycles. The Student t test with 5% significance level was used to evaluate the data. Results: HEX group demonstrated significantly higher axial displacement values after 30 Ncm tightening in comparison to the CON group (P < 0.05). No significant difference was found in axial displacement after cyclic loading (P = 0.052). Removal torque loss before and after the cyclic loading both revealed no significant difference between groups (P = 0.057 and P = 0.138). Removal torque value decreased after cyclic loading in both groups (P < 0.05). Conclusion: Overall, both abutment with or without hexagon index presented similar biomechanical performance except HEX group demonstrated significantly more axial displacement after applying tightening torque.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.24 no.6
• /
• pp.707-714
• /
• 2011

The inter-story drift ratio is used to evaluate the damage of buildings by the earthquake. This is known that as the inter-story drift ratio decreases, the seismic damage decreases. Although to reduce the inter-story drift ratio is the important issue in the seismic design, no practical inter-story drift design method has bean developed. This study presents an optimal inter-story drift design method to improve the seismic performance of the steel moment frames using the resizing algorithm. The objective function of the proposed method is to minimize the differences of the inter-story drift ratios so that the inter-story drift ratios of the building could be distributed evenly and be reduced. Because this method redesigns the sectional properties of structural members base on the displacement participation factor calculated by the unit-load method, this can improve the seismic performance of the structure without the iterative structural analysis. The efficiency of this algorithm was demonstrated by the application to steel moment frames.

• Journal of Korean Society of Steel Construction
• /
• v.18 no.3
• /
• pp.361-371
• /
• 2006

In recent years, to overcome drawbacks related to the aplicati on of classical structural optimization algorithms, various drift design methods based on factores of member displacement participation factors have been developed to size members if they satisfy stiffness criteria. In particular, a resizing algorithm based on dynamic displacement participation factors from the response spectrum analysis has been applied in the drift design of steel structures subjec ted to seismic lateral forces. In this aproach, active members are selected for displacement control based on the displacement participation fa ve members may be taken out and added to the active members for the drift control. The resizing algorithm can be practically and effectively applied to drift design of high-rise buildings however, the inelastic behavior o f the resizing algorithm has not ben evaluated yet. To develop the resizing algorithm considering the performance of nonlinearity as well a s elastic stifness, the evaluation model of resizing algorithm s is developed and aplied to the examples of moment-resisting steel frame, which is one of the simplest structural systems. The inelastic behavior of moment-resisting steel frame designed by the resizing algorithm is also discussed.

• The Journal of Korean Academy of Prosthodontics
• /
• v.25 no.1
• /
• pp.281-302
• /
• 1987

의치상 재료 종류에 따라 의치, 점막 및 하악골에 발생되는 변위 및 응력을 연구하기 위하여 컴퓨터를 이용한 수치적 해석인 2차원 유한 요소법을 이용하였다. 2차원 유한 요소 모형으로선 표준 크기의 하악골 및 의치를 고려하여 231개의 사변형 요소 및 268개의 절점으로 분할한 후 각 구성 성분의 물리적 성질인 탄성률 및 프와송비를 대입시켰다. 사용된 의치로서는 일반 합성수지의치, 2mm후경의 탄성재를 의치상 하부에 이장한 합성수지의치, 2mm후경의 탄성재를 치아와 의치상 중앙에 삽입한 합성수지의치 및 0.5mm후경의 금속상의치의 4종류였으며, 하중시에 하악의 고정 부위로선 생체와 동일 조건을 부여하기 위하여 교근, 내측익돌근, 측두근등의 하악 폐구근이 부착되는 하악각 부위 및 하악 근돌기 부위의 16절점을 고정점으로 하였다. 하중 조건으로선 하악 제1대구치의 일점에 10kg의 수직 집중하중, 하악 중절치의 일점에 7kg의 수직 집중하중 및 하악 제 1소구치로 부터 하악 제2대구치까지의 교합면에 10kg의 수직 분산하중을 부여하여 분석한 결과는 다음과 같다. 1. 하중이 의치 교합면위의 가해진 부위에 따라 다양한 의치 회전 및 강하 현상을 보였으며, 탄성재를 이장 및 삽입한 합성 수지 의치의 변위가 일반 합성수지의치 및 금속상 의치의 변위보다 더 컸다. 2. 주응력을 고려할때 점막 부위에는 주로 압축 응력이 작용하였으며 치조제 부위는 압축응력과 인장 응력이 함께 작용하였다. 3. 탄성재를 삽입한 합성수지의치에 최고 등가 응력이 집중되었으며 그 다음은 탄성재를 이장한 합성수지의치, 일반 합성수지의치의 순이였으며 금속상의 경우는 금속을 따라서 높은 등가 응력이 넓게 분산되었다. 4. 의치상 종류에 관계없이 동일 하중 조건하에선 점막에 나타나는 등가 응력의 크기 및 분산양태는 유사하였다. 5. 하악골에서 등가 응력은 의치지지 부위에만 국한되지 않고 넓게 분산 되었으며 의치상 종류 및 하중 조건에 관계없이 치조제 후방 및 하악연의 후방 부위에 특히 높은 등가응력이 집중되었다. 6. 하악 중절치의 일점에 수직 하중을 가한 경우가 다른 하중 조건에 비하여 지지점과의 거리차이로 인하여 하악골에 가장 높은 등가 응력을 유발하였다. 7. 의치상 재료에 따른 하악 골에 발생되는 응력의 크기 및 분산에는 큰 차이가 없으나 금속상의 경우가 교합압을 분산하는데는 효과적이었다.

• Journal of the Korean Institute of Gas
• /
• v.20 no.3
• /
• pp.73-77
• /
• 2016

This paper presents the displacement behavior safety of hollow shafts with an equivalent volume for various cross sectional area using a finite element method. The FEM results indicate that the hollow shafts with X-type or Y-type columns between outer tube, middle tube and inner tube may reduce a maximum displacement at the middle length of hollow shafts. Especially, the load-bearing column of X-type or Y-type hollow shaft is directly connected between outer tube and inner tube without a shift for reducing the vertical displacement. And increased thickness of a load-bearing column is recommended for reducing the vertical displacement and increasing the displacement behavior safety for an equivalent volume of a hollow shaft.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.6
• /
• pp.701-708
• /
• 2010

The stress and displacement fields of a permeable propagating crack in orthotropic piezoelectric materials under anti-plane shear mechanical load and in-plane electric load are analyzed. The equations of motion for the propagating crack in piezoelectric materials are developed and the solution on the stress and the displacement fields through an asymptotic analysis was obtained. The influences of the piezoelectric constant and of the dielectric permittivity on the stress and displacement fields at the crack tip are explicitly clarified. Using the stress and displacement fields obtained in this study, the characteristics of stress and displacement at a propagating crack tip in piezoelectric materials are discussed.

• Elastomers and Composites
• /
• v.38 no.4
• /
• pp.334-341
• /
• 2003

A bushing is a device used in automotive suspension systems to reduce the load transmitted from the wheel to the frame of the vehicle. A bushing is a hollow cylinder, which is bonded to a solid steel shaft at its inner surface and a steel sleeve at its outer surface. The relation between the force applied to the shaft and the relative deformation of a bushing is nonlinear and exhibits features of viscoelasticity. A force-displacement relation for bushings is important for multibody dynamics numerical simulations. For the nonlinear viscoelastic axial response, Pipkin-Rogers model, the direct relation of force and displacement, has been derived from Lianis model and the sinusoidal input was used fer Pipkin-Rogers model, and the affection of displacement with frequency change was studied with Pipkin-Rogers model.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.6 no.2
• /
• pp.171-182
• /
• 2004

This study is focused on finding out the mechanical behavior of pillars and the ground adjacent to the tunnel depending on the central tunnel size and the invert during the construction of 2 arch tunnels in the sandy ground. Model tests were performed in the trap door system, which was composed of 3 separately movable plates. Central pillar was installed on the central movable plate to measure the pillar loads during the excavation of pilot tunnel and the main tunnel. The load-transfer and the loosening load were measured at the bottom plates adjacent to the 2 arch tunnels. The ground settlement and displacement of the tunnel lining were also measured. As results, not only pillar load but also the load transfer mechanism was influenced by the construction sequences, central tunnel size, and the invert.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.13 no.1
• /
• pp.45-52
• /
• 2009

The purpose of this study is to evaluate the structural capacities of beam-column specimens retrofitted with CFRP sheet and BRB (Buckling-Restrained Brace) under sustained axial and cyclic lateral loads. Three specimens were made using different retrofitting methods : non-retrofitted, retrofitted with CFRP sheets only, and retrofitted with both CFRP sheet and BRB systems. Lateral load resistant capacities were evaluated based on the load-displacement relations. From the results, the maximum lateral forces of the FRP sheet retrofitted and both the FRP and BRB retrofitted specimens showed approximately 34% and 138% improvement, respectively, compared with the non-retrofitted specimen.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.27 no.5
• /
• pp.599-605
• /
• 2009

Changes of atmospheric pressures cause short- and long-term crustal deformations and thus become error sources in the site positions estimated from space geodesy equipments. In this study, we computed daily displacements due to the atmospheric pressure loading (ATML) at the 14 permanent GPS sites operated by National Geographic Information Institute. And the 10-year GPS data collected at those stations were processed to create a continuous time series of the height estimate. Then, we corrected for the ATML from the GPS height time series to see if the correction changes the site velocity and improves the precision of the time series. While the precision improved by about 4% on average, the velocity change was not significant at all. We also investigated the overall characteristics of the ATML in the southern Korean peninsula by computing the ATML effects at the inland grid points with a $0.5^{\circ}{\times}0.5^{\circ}$ spatial resolution. We found that ATML displacements show annual signals and those signals can be fitted with sinusoidal functions. The amplitudes were in the range of 3-4 mm, and they were higher at higher latitudes and lower at the costal area.