• Journal of Korean Society of Steel Construction
• /
• v.8 no.4 s.29
• /
• pp.31-42
• /
• 1996

본 연구에서는 박벽 구조물의 기하학적 비선형 해석을 수행하기 위하여 개선된 하중 및 변위 증분의 조합법이 제시되었다. 제안된 알고리즘은 기존의 하중 및 변 변위 증분의 조합법 이 고정된 증분량을 갖는 점을 개선하여, 수렴정도에 따라 증분량을 변화시킴으로써, 여러개의 임계점을 갖는 비선형 거동을 보다 효율적으로 추적하도록 하였다. 또한 하중 및 변위 증분법을 전환점을 첫 단계의 기울기에 비례한 값으로 대체함으로써 사용자의 편리를 도모하였다. 트러스, 공간 뼈대, 아치, 쉘 구조물 등의 기하학적 비선형 해석 예제를 통하여, 본 연구에서 제시한 개선된 하중 및 변위 증분의 조합법의 적용성을 입증하였다.

• Bulletin of the Korean Space Science Society
• /
• 2003.10a
• /
• pp.30-30
• /
• 2003

GPS와 VLBI와 같은 우주측지 기술을 이용한 정밀 측위는 수 mn 정밀도의 관측소 좌표결정과 1 mm/year 정도의 고정밀 속도결정에 이용된다. 이를 위해서는 여러 가지 오차 요인들과 다양한 물리적 현상에 대한 모델링이 이루어져야 한다. 그 중의 하나가 해수 하중(ocean loading)에 의한 수직방향의 지각변위이다. 특히 한반도의 서해안은 복잡한 리아스식 해안으로 이루어져 있고, 조수간만의 차이가 크기 때문에 현존하는 모델의 정확도가 떨어진다. KVN(Korean VLBI Network)사업에서 추진하는 3기의 VLBI 중 2기가 서울과 제주도에 설치될 계획이므로, 해수하중에 의한 지각변위에 관한 연구가 선행되어야 한다. 또한 국내 GPS상시관측소의 많은 수가 서해안 지역에 설치되어 있다. 본 연구에서는 서해안 지역의 해수하중에 의한 수직방향의 지각변위를 GPS로 관측하고 이를 서해안 해수조류 모델의 정밀도를 향상시키는데 필요한 기초연구를 수행하였다. 서해안의 4개 GPS 관측소 위치에서의 해수하중에 의한 지각변위를 계산해본 결과 인천 지역에는 3 cm에 육박하는 지각변위가 수직으로 발생함을 알 수 있었다. 같은 크기와 위상의 지각변위 진폭을 GPS로 검출하기 위한 여러 가지 오차 보정과 GIPSY를 이용한 고정밀 키네마틱 GPS 자료처리에 대하여 상세히 소개한다.

• The Journal of the Acoustical Society of Korea
• /
• v.16 no.4
• /
• pp.21-28
• /
• 1997

In this study, comparison between Harris-theoretical values and experimental data of load-deflection characteristics in bearing was made. The experiments are conducted under the conditions of the various radial loads and speed of shaft. In the case of non-defective ball bearing, the experimental data agreed well with the Harris-theoretical values for the small steady radial load but not for the large steady radial load. For the radial load bearing, the experimental results show that the stiffness of bearing at the single and multiple defective bearing are bigger in the radial defectiion than in the axial deflection. Load-deflection characteristics for the bearing defect part make it possible to detect the presence of a defect in bearing.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.19 no.4 s.74
• /
• pp.357-367
• /
• 2006

Drift design methods using resizing algorithms have been presented as a practical drift design method since the resizing algorithms proposed easily find drift contribution of each member, called member displacement participation factor, to lateral drift to be designed without calculation of sensitivity coefficient or re-analysis. Weight of material to be redistributed for minimization of the lateral drift is determined according to the member displacement participation factors. However, resizing algorithms based on energy theorem must consider loading conditions because they have different displacement contribution according to different loading conditions. Furthermore, to improve practicality of resizing algorithms, structural member grouping is required in application of resizing algorithms to drift control of high-rise buildings. In this study, three resizing algorithms on considering load condition and structural member grouping are developed and applied to drift design of a 20-story steel-frame shear-wall structure and a 50-story frame shear-wall system with outriggers.

• Magazine of the Korea Concrete Institute
• /
• v.9 no.1
• /
• pp.183-194
• /
• 1997

Traditional displacmir~nt measurement included an extrancous and cvrntlc. portmn due to test setup and support crushing. The magnitudc of this erroneous deformation was found to be of the same order as the actual displacement, leading to inaccurate determinations of fracture parameters. To overcome this problem, the load-CMOD relationship is a more reliable parameter for determining the fracture characteristics because it is unaffected by the specimen setup and any support crushing. An important step towards the use of load-(:MOD concept as a key fracture parameter depends on relating the CMODto the traditional load-line deflection. This investigation found that there was an unique linear relationship between the CMOD and the load-line deflection. The exact numeric value of relationship between the CMOD and the deflection. that is, the slope ofthe line, is discovered to be a material property. The relationship finds a problem with the existing IZIL,EM recommendations for. measuring the fracture energy of concrete. A proposal to correct the problem is made.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.10
• /
• pp.4642-4647
• /
• 2011

Solution for elastic foundation of plane strain state was derived by the application of variational method. Functions of the transverse distribution of the displacements for the analysis were chosen as linear functions. Loading conditions considered for the analysis were concentrated load and distributed load. Under the loading condition of the concentrated load, surface displacement was decreased drastically as the distance from the point of the loading increased. Under the loading condition of the distributed load, surface displacements were more uniformly distributed beneath the loading area when the ratio of the half of the loading width to the depth(B/H) of the compressible layer was greater. The surface displacement was more quickly converged from the edge of the loading area as the ratio(B/H) increased.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.18 no.5
• /
• pp.487-497
• /
• 2016

If a tunnel is excavated, the released stress is redistributed in the ground around the tunnel face, which lead the stress state of the surrounding ground of the tunnel and the load acting on the tunnel support to change. If the tunnel face deforms, the ground ahead of it is relaxed, and the earth pressure acting on it decreases. And if the displacement increases so much that, the ground ahead of the tunnel face reaches in failure state. At this time, load would be transferred longitudinally in the tunnel, depending on the cover and the face deformations. The longitudinal load transfers in the tunnels induced by the tunnelling has been often studied; however, the relation between the deformation of the tunnel face and the longitudinal load transfer was rarely studied. Therefore in this study assesses the characteristics of the longitudinal load transfer as the face was failed by displacement by conducting a model test in a shallow tunnel. In other words, the longitudinal load transfer of the tunnel with the progress of the face deform was measured by conducting a model test, beginning at the state of earth pressure at rest. As results of this study, most of the longitudinal load transfers occurred drastically at the beginning of the displacement of the tunnel face, and as the displacement of the face approached the ultimate displacement, it converged to the ultimate displacement at a gentler slope. In other words, when the ground ahead of the tunnel face was still in an elastic state, the longitudinally transferred load increased sharply at the beginning stage but it tended to increase gradually if it approached to the ultimate limit. Thus, it was noted that the earth pressure in the face and the longitudinal load transfer of the tunnel had the same decreasing tendency.

• Proceedings of the Korean Institute of Industrial Safety Conference
• /
• 1999.06a
• /
• pp.181-186
• /
• 1999

반복하중에 따른 P.C 구조물의 장착장치로 사용되는 Wedge 형상에 따른 거동특성을 파악하기 위하여 정적최대하중을 이용하여 피로시험을 수행하였다. 또한 피로시험 결과로부터 반복회수에 따른 시험 체의 균열양상, 하중-변위, 하중-변형율, 하중-중앙 최대 변위, 하중-영구 변형량, 반복횟수에 따른 S-N선도 등을 고찰하였다. (중략)

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.12 no.4
• /
• pp.61-70
• /
• 2008

In this research, load-transfer-function method was selected, because that is widely used in geotechnical engineering among the analysis methods to verify the behavior of load-lateral displacement. Lateral loading test of field scale was conducted, this measured data was analyzed. From the analysis, the model of load-lateral displacement was suggested. The test results were studied and compared to the commercial programs, 'LPILE', which contain the load transfer functions proposed before. By analysis of measure data of load-lateral displacement that expressed to several functions, $y=ae^{bx}$ model was the simplest and applicable to the field. In that case a value converged about 1.3, b value had a tendency to converge about 0.02. From the comparison analysis between measured data and load transfer function by 'LPILE', it is examined that if the lateral load is small, calculated displacements of them show a similar value compared to measured values. Furthermore, the bigger lateral loads, the bigger calculated values compared to the measured data. If the results are compared by Matlock-Reese method and Matlock-API method, Matlock-Reese method shows result of safe side because lateral displacement is calculated greatly relatively.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.18 no.5
• /
• pp.499-509
• /
• 2016

In recent years, the use of underground spaces becomes more frequent and the demands for urban tunnels are rapidly increasing. The urban tunnels constructed in the ground with a shallow and soft cover might be deformed in various forms on the face, which would lead, the tunnels to behavior 3-dimensionally, which may have a great impact on the longitudinal load transfer. The tunnel face might deform in various forms depending on the construction method, overburden and the heterogeneity of the ground. And accordingly, the type and size of the distribution of the load transferred to the ground adjacent to the tunnel face as well as the form of the loosened ground may appear in various ways depending on the deformation form of the tunnel face. Therefore, in this study was conducted model tests by idealizing the deformation behavior of the tunnel face, that were constant deformation, the maximum deformation on the top and the maximum deformation on the bottom. And the test results were analyzed focusing on the deformation of the face and the longitudinal load transfer at the ground above the tunnel. As results, it turned out that the size and the distribution type of the load, which was transferred to the tunnel as well as the earth pressure on the face were affected by the deformation type of the face. The largest load was transferred to the tunnel when the deformation was in a constant form. Less load was transferred when the maximum deformation on the bottom, and the least load was transferred when the maximum deformation on the top. In addition, it turned out that, if the cover became more shallow, a longitudinal load transfer in the tunnel would limited to the region close to the face; however, if the cover became higher than a certain value, the area of the load transfer would become wider.