• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.47-47
• /
• 2010

게이트 밸브는 진공 시스템 구성에 있어서 빠질 수 없는 중요한 부품 중 하나로 공간을 구획하여 필요에 따라 자유롭게 진공 상태와 대기 개방 상태가 공존하도록 만들어 주며 진공펌프와 같은 주요 기기들의 탈착 및 교체를 용이하게 해 준다. 게이트 밸브는 열린 상태에서는 저항이 최소화되는 반면 닫힌 상태에서는 마치 마구리 플랜지로 막은 것처럼 완벽한 차단이 요구된다. 일반적으로 게이트 밸브 상용제품은 개스킷이 닿는 밸브 시트가 한쪽에만 마련되어 있으므로 디스크 기계구조가 충분한 압력을 발휘하지 못한다면 어느 쪽이 대기압인가에 따라 디스크를 미는 힘의 크기가 변하여 기밀특성이 달라질 수 있다. 따라서 게이트 밸브의 누설검사는 순방향과 역방향 모두에 대해 시행해야 한다. 양방향 누설검사를 위해 한쪽 밸브 공간을 배기하고 반대쪽 공간에 헬륨을 뿌리는 작업을 교대로 하려면 배기시간의 단축과 신속한 잔류 헬륨기체 제거가 필수적이다. 게이트 밸브 제조 공장에서 상품을 출하하기 위한 시험검사라는 것을 전제로 합리적인 시간 내에 정확한 누설검사를 일관성 있게 할 수 있는 적절한 누설검사 시스템을 설계하고 측정절차를 상용 게이트 밸브에 대해 적용해 보았다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.115-115
• /
• 2004

최근에는 자동차용 범퍼(Bumper), 인판넬(In-panel), 도어판넬(Door panel), 도어가니쉬(Door Garnish) 등과 같은 대형 사출성형품을 성형하기 위한 금형설계에 핫 러너 시스템(Hot Runner System)에 밸브 게이트(Valve Gate)를 채용한 밸브 게이트 시스템을 많이 사용하고 있다 이 시스템을 사용함으로서 성형 싸이클타임의 단축, 수지 스크랩의 감소 등의 말은 장점이 있으나, 실제 성형작업 적용 시 밸브 게이트의 작동순서 및 개폐시간의 제어 등에 정확한 표준이 없어 시험 사출시 최적 성형조건의 셋팅이 많은 시간을 소모하고 있는 문제점이 있다.(중략)

• Journal of the Korean Society of Propulsion Engineers
• /
• v.11 no.6
• /
• pp.35-41
• /
• 2007

The rate of loading in motor operated valve(MOV) can be defined as a variation of correlation between the actuator torque and the thrust upon the variation of operating load. This paper contains the analysis of characteristic and the validity of loading rate in the opening stroke of gate type motor operated valve. Also, this paper describes the evaluation result of loading rate for 40 MOVs' opening stroke using newly derived methodology in this study. Author has found a result that loading rate of opening stroke gets a negative value when the differential pressure is higher than 150 psi and this value goes up depending on the amount of the differential pressure.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.2
• /
• pp.157-164
• /
• 2017

A parallel slide gate valve (PSGV) is located between the heat recovery steam generator (HRSG) and the steam turbine in a combined cycle power plant (CCPP). It is used to control the flow of steam and runs with repetitive operations such as startups, load changes, and shutdowns during its operation period. Therefore, it is necessary to evaluate the fatigue damage and the structural integrity under a large compressive thermal stress due to the temperature difference through the valve wall thickness during the startup operations. In this paper, the thermal-structural analysis and the fatigue life evaluation of a 16-inch PSGV, which is installed on the HP steam line, is performed according to the fatigue life assessment method described in the ASME B&PVC VIII-2; the method uses the equivalent stress from the elastic stress analysis.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1999.05a
• /
• pp.471-472
• /
• 1999

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.10
• /
• pp.884-888
• /
• 2007

It is necessary to evaluate periodically the performance of the AOV(air-operated valve) which is used for controlling flow and pressure in nuclear power plant. The required thrust for actuating valve and available thrust of actuator are calculated with conditions of flow through a valve in this study and operating performance is analyzed through comparing two thrusts. In general, differential pressure is increased according to increase the flow rate and differential pressure affects the required thrust of valve. We found the fact that it is possible not to close the valve perfectly because required thrust becomes bigger than available thrust of actuator.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.2 s.257
• /
• pp.151-158
• /
• 2007

The mechanism of power transmission from motor torque to stem thrust and the operation characteristic of each stroke position are analyzed using the diagnostic signal, and effects of differential pressure on the performance of motor operated flexible wedge gate valve are investigated. Test facility consists of 76 mm motor operated valve(flexible wedge type), pump and pipe system. Static and dynamic test are performed separately, and two differential pressure conditions are applied in the dynamic test. To evaluate the performance of valve, test signals for the torque, thrust, current, voltage and stroke length are acquired by using UDS which is diagnosis device for motor operated valve, and each diagnostic signal is analyzed and compared. The characteristic of valve performance factors such as stem factor, rate of loading, valve factor, are evaluated, and these factors are found to be severely influenced by the fluid differential pressure.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.10a
• /
• pp.686-686
• /
• 2013

Automotive turbochargers have become common in gasoline engines as well as diesel engines. They are excellent devices to effectively increase fuel efficiency and power of the engines, but they unfortunately cause several noise problems. The noises are classified into mechanical noises induced from movement of a rotating shaft and aerodynamic noises by air flow in turbochargers. In addition to, there is a mechanical noise caused from movement of an actuator, electronically controlling a wastegate valve. It is called as valve rattle noise. The actuator is connected to a valve through a linkage. The noise occurs only if the valve is open, where the linkage is freely contact to neighbor structures without being constrained by any external forces. This condition allows impacts by the pulsation of exhaust gas, and the vibration from the impacts spreads out through turbine housing, causing the rattle noise. The noise is not in mechanical operating wastegate turbochargers because the linkage of an actuator is strongly connected by actuating force. For the electronic wastegate turbocharger, this paper proposed a test device to show the noise generating mechanism with a small vibration motor having an unbalanced shaft. It also shows how to reduce the noise - reduction of linkage clearances, inserting wave washers into a connection, and applying loose fitting in bushing embracing a valve lever to turbine housing.

• The KSFM Journal of Fluid Machinery
• /
• v.10 no.5
• /
• pp.46-53
• /
• 2007

Stem friction coefficient and valve factor are very important parameters for the evaluation of valve performance. In this study, the characteristics of stem friction coefficient and valve factor are analyzed, and thor bounding value is determined. The hydraulic testing is performed for many flexible wedge gate valves in the plant and statistical method is applied to the determination of bounding value. According to the results of this study, stem friction coefficient does not change much with differential pressure, and the bounding value of closing stroke is higher than that of opening stroke. The valve factor of valves with high differential pressure is higher than that of valves with medium differential pressure. It means valve factor is more sensitive to the differential pressure than the stem friction coefficient. Valve factor of the closing stroke is higher than that of opening stroke due to piston effect.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.6 no.1
• /
• pp.71-77
• /
• 2007

In case of the welding process, a conventional production method of gate valve, it has a merit of light weight, but also a demerit of high production cost and an impossibility in mass production due to work by hand. However, in case of the forging process, it has economic merits and can take a mass production process, too. The main focus of this paper is the optimization of preform in the forging process. This paper proposed an optimal design to improve the mechanical efficiency of gate valve made by forging method instead of welding. the optional design is conducted as application of real response model to Kriging model using computer simulation. Also, from verification of the response model with optimized results we were confirmed that the applications of Kriging method to structural optimum design using finite element analysis and equation are useful and reliable.