• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.12
• /
• pp.453-458
• /
• 2016

While the design of weirs requires a scour-considered strategy, research on the analysis of the effectiveness of hydraulic energy dissipaters and design criteria are scarce due to the limited experimental facilities and restraint in the experiment conduction period. The study analyzed the scour dissipation effect of multidirectional dissipaters to improve the scour problems of a weir downstream and suggests design criteria to minimize scour. A hydraulic model experiment was conducted for Nakdong River Hapcheon-Changnyeong Weir and a model in 1/25 of horizontal accumulation and 1/25 of vertical accumulation was produced. The experimental equipment was classified into channels and a flow rate supply and an underwater pump were installed to enable flow at a maximum of 2.0 m3/s. The experimental inflow was 1.3 m3/s, the upstream water level was 0.36 m, downstream water level was 0.24 m, and a cylinder wooden baffle, a dissipater, with a diameter of 0.05 m was made. A 3D scanner was also used for an accurate scour depth comparison for a length change of the baffle before and after installing the baffle. When the baffle was arranged in the shape of a V, the depth of scour decreased by 36% while the scour length decreased by 49% due to flow reduction compared to that before installing the baffle.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.8
• /
• pp.720-725
• /
• 2007

Cold acoustic tests have been performed to elucidate the effect of baffle gaps on the optimal damping characteristics in a liquid rocket combustor where coaxial injectors are installed. For several axial baffle lengths, an optimal acoustic damping capacitance has been achieved in a certain gap range. Cold acoustic tests for simulating fluid viscosity by changing the pressure in a model chamber have been done to study the main mechanism of optimal damping. Experimental data have shown that the optimal gap for high damping capacity exists mainly due to the viscosity near the gap of baffles. Therefore, axial baffle length can be reduced by using the optimal baffle gap, providing a possible solution of thermal cooling problems. Also, these optimum characteristics can be some guidelines for manufacturing and assembling injectors in full-scaled rocket combustors.

• The Bulletin of The Korean Astronomical Society
• /
• v.43 no.1
• /
• pp.39.4-40
• /
• 2018

KMTNet 광시야 망원경의 성능 개선을 위해 2017년에 이루어진 주요 작업으로 주경 배플(baffle) 설치, 주경 코팅, 돔 플랫(dome flat) 장치 설치에 대해 발표한다. 망원경 주경의 가장자리(turn down edge)는 경면 가공이나 코팅 상태가 균질하지 않을 수 있으며, 이로 인한 난반사는 밝은 별 주위에 넓은 wing profile과 여러 갈래의 방사상 빛줄기를 만든다. 이런 난반사를 제거하기 위해 주경면 바로 앞에 배플을 설치하였다. 주경의 광학 성능과 집광력이 최적이 되도록 배플 내부 직경 값을 1,580 mm로 조정하여 설치한 결과, 관측 영상에서 별의 영상이 크게 개선되었다. 호주 관측소는 상대적으로 습기가 높아서 망원경 주경의 반사율이 빨리 낮아졌으며, 이를 개선하기 위해 기존의 코팅(protected silver)을 제거하고 알루미늄으로 새로 코팅하였다. KMTNet 3개 관측소는 주경의 반사율과 코팅 면의 확대 영상을 정기적으로 모니터링하여 광학 성능의 변화를 추적하고 있다. 밤하늘 플랫(twilight sky flat) 영상을 보완하기 위해, 돔 인클로져에 플랫 스크린과 광원을 설치하여 돔 플랫 영상을 획득하였다. 마지막으로 KMNet 관측시스템을 운영하며 발생한 돔 회전 및 돔 셔터 구동부 문제 등에 대해 소개하고, 문제 발생 원인과 주기, 문제 해결 방안을 발표한다.

• Journal of Korea Water Resources Association
• /
• v.54 no.1
• /
• pp.15-25
• /
• 2021

The purpose of this study was to present the necessity and effect of culvert fishway, based on the absence of design criteria for it which fishes can pass. As an attempt for this purpose, circular culvert fishway were designed hydraulically to meet the passage condition for selected target fish species, and post-monitoring was performed to confirm its effectiveness. In the case of general circular culvert without weir baffles, the target fish species cannot pass because of the constant depth and velocity in the entire reach of the circular culvert, so it was confirmed that resting pools must be installed to help fish passage. In the case of circular culvert with weir baffles, the depth and the mean velocity in resting pool increased by about 240% and decreased by about 70% respectively, which not only satisfied the passage conditions of Zacco platypus that can swim at more than 10 times the speed of body length for 1 to 5 seconds, but also confirmed that various river fish could pass. Post-monitoring results of the restoration reach and fish capture monitoring surveys of circular culvert fishway demonstrated that the target fish species, Zacco platypus, can pass through it.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.2
• /
• pp.32-39
• /
• 2005

The effectiveness of the pogo suppression device (PSD) on the response of the piping system simulating the fuel (or oxidizer) supply lines of the rocket engines was investigated. The system response defined as the ratio of the flow rate to the pressure in the main tube was obtained for various PSD gas volumes $((0\~2)\times10^{-3}m^3)$ and three different baffle hole diameters (5, 50, 115mm). Existence of a gas volume in the PSD reduced the system resonance frequency. With a larger gas volume, the resonance frequency became lower, but only slightly, while the fluctuations of the main tube pressure and the flow rate damped down considerably. The resonance frequency decreased with the increase of the PSD inlet restriction (or the decrease of the baffle hole diameter), though slightly. However, with a larger inlet restriction, the PSD pressure wave showed a delayed response with the smaller amplitude compared to the pressure variation in the main tube.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.15 no.1
• /
• pp.147-154
• /
• 2002

The dynamic load caused by sloshing of internal fluid severely affects the structural and control stabilities of cylindrical liquid containers accelerating vertically. If the sloshing frequency of fluid is near the frequency of control system or the tank structure, large dynamic force and moment act on launching vehicles. For the suppression of such dynamic effects, generally flexible ring-type baffles are employed. In this paper, we perform the numerical analysis to evaluate the dynamic suppression effects of baffle. The parametric analysis is performed with respect to the baffle inner-hole diameter and two different baffle spacing types : equal spacing with respect to the tank and one with respect to the fluid height. The ALE (arbitrary Lagrangin-Eulerian) numerical method is adopted for the accurate and effective simulation of the hydrodynamic interaction between fluid and elastic structure.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.7
• /
• pp.581-588
• /
• 2014

The inlet/outlet flow in the tube-side of the shell and tube heat exchanger was experimentally measured to investigate the effect of the porous baffle on uniform flow distribution. A 1/3rd scale-downed model of a heat exchanger was used and particle image velocimetry was applied for measuring the instantaneous velocity vector fields. The absolute errors in the flow rate were calculated and compared for the tube-side with and without the porous baffle, by varying the flow rate from 60 to 90 LPM. The results revealed that the porous baffle can improve flow uniformity and reduce the absolute error in the flow rate of the model with the baffle by about 74%, compared to that without the baffle. This result can be used for improving the performance and design of the shell and tube heat exchanger.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.9
• /
• pp.862-869
• /
• 2010

Numerical analysis was done to evaluate the gas flow distribution in small scale SCR system which has $2.4{\times}2.4{\times}3.1\;m^3$ in volume and 25,300 Sm3/hr in flue gas flow capacity. Various types of baffles proposed for controlling the flow uniformity were evaluated by the CFD analysis to find the optimal geometry of the baffle in the SCR system. By installing baffles in the SCR system, the RMS (%) value was raised up to 6.2% compared with the baffle-uninstalled state. The effect of baffle thicknesses on the RMS (%) value was not shown within 0 and 8 mm in thickness, but the RMS (%) value was raised by 2.5% in 10 mm of baffles thickness, which causes the unstability in flow. By comparison between the shape of baffles, it is known that the lattice type baffle has better performance in controlling the flow uniformity than the circular truncated cone type baffle or mixer type baffle. RMS (%) values have more that 10% difference according to the shape of baffle type.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.2
• /
• pp.74-81
• /
• 2004

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.36-36
• /
• 2000

KSTAR 토카막은 보조가열 장치로 2005년까지 1대(최종적으로는 2대)의 중성입자빔 입사장치(NBI)를 설치하여 장치의 기본 설계값에 도달할 예정이다. KSTAR NBI는 3개의 이온원을 가지고 있으며 총 수소 유입량은 70 Torr.L/s인 반면 고속 중성 입자빔량은 모두 11 Torr.L/s로 기체 배기량은 59 Torr.L/s에 달하고 압력은 장소에 따라 10-5~10-6 Torr로 유지되며 총배기속도가 1~2$\times$106 L인 펌프가 필요하다. 이때 크라이오 펌프(cryopump) 방식이 거의 유일한 해결책이라고 할 수 있다. 크라이오 펌프는 고속 입자빔 수송로의 양편에 각각 설치되는데 총면적 30m2 내외의 극저온 냉각판(cryo-pnael)들과 이를 상온 열복사로부터 보호하기 위한 열차폐(thermal shield) 및 흡기구 배플(baffle), 그리고 적절한 냉각장치로 구성된다. 시운전 단계에서는 15K GM 냉동기와 활성탄이 부착된 냉각판을 사용하는 방식과 4K GM 냉동기로 냉각하는 방식이, 최종 운전단계에서는 3.7K 액체 헬륨을 사용하는 방식이 고려되고 있다. 크라이오 펌프의 구조설계에 앞서 우선 배기속도, 흡？량, 작동압력, 냉각판 온도, 열손실량 등 설계사양을 확정하고 정리하는 일이 진행되고 있다. 또 냉각방식과 상관없이 동일한 개념으로 만들어지는 배플과 열차폐의 최적설계를 위한 몬테카를로 계산과 열전도 계산을 병행하고 있다. 이 곳에서는 KSTAR NBI 장치의 주배기계로서 사용될 크라이오 펌프의 설계방향과 전반적인 구조 및 예상성능 등에 대해 발표하려고 한다.