• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.4B
• /
• pp.388-396
• /
• 2002

In this paper, An aperture-coupled microstrip patch antenna operating at WLL frequency range(Rx : 2.3∼2.33Ghz, Tx : 2.37 ∼2.4Ghz) for WLL repeater is designed and fabricated. FR-4 epoxy substrate with 4.7 relative permittivity is inserted between feed-line and patch plane. Aperture-coupled structure is employed for consideration of bandwidth improvement and gain\`s characteristics. Air gap is arranged at each layer for bandwidth extension and radome is used as a protector in the upper patch. In this paper, both 1 port and 2 port are designed as 1$\times$2 array antenna which uses T-junction and λ$\_$g//4 transformer. Here, 1 port is used as transmitting/receiving antenna and 2 port is used as receiving antenna. Functionally independent two antennas using space diversity arrange slots between two antennas in order to be placed at the same place. As a result, we obtained a excellent isolation below -40dB and return loss is reduced by means of slots arrangement between patch and antenna.

• The Journal of the Acoustical Society of Korea
• /
• v.23 no.4
• /
• pp.288-295
• /
• 2004

Detection and localization of a slow and quiet target in shallow water environments is a challenging problem for which it is well known that snapshot is deficient because of a fast and strong interferer. This paper presents waveguide interference filtering technique that mitigate strong interferer problems in adaptive matched field processing. MCM (multiple constraint method) based on NDC (null direction constraint) has been proposed for new spatial interferer filter. MCM-NDC using replica force a interferer component to be filtered through CSDM (cross-spectral density matrix). This filtering have an effect on sidelobe reduction and restoring of signal gain of a quiet target. This technique was applied to a simulation on Pekeris waveguide and vertical array data from MAPLE03 (matched acoustic properties and localization experiment) in the East Sea and was shown to improve SBNR (signal-to-background-and-noise ratio) over the standard MVDR (minimum-variance distortionless response) and NSP (null space projection) technique.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.49 no.6
• /
• pp.57-62
• /
• 2012

In this paper, WCDMA indoor repeater antenna using an absorber based on metamaterial structure for high isolation is proposed. The proposed antenna consist of the main patch with the absorber based on metamaterial structure and parasitic patch. The WCDMA bandwidth is obtained by utilizing the coupling between the main and parasitic patches. The size of the absorber based on metamaterial structure is $13mm{\times}13mm$, the absorption is about 94 % at 2.18 GHz. The isolation characteristic of proposed WCDMA indoor repeater antenna between the service and donor antennas is improved by using a absorber based on metamaterial. The proposed WCDMA indoor repeater antenna has a gain higher than 6 dBi with a VSWR less than 2, and an isolation between the service and donor antennas greater than 85 dB over the WCDMA band from 1.92 GHz to 2.17 GHz. And size of the proposed antenna is $75mm{\times}75mm$.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.6
• /
• pp.21-28
• /
• 2016

This paper presents a cooperative transmission scheme for underwater acoustic sensor networks to improve packet transmission rate and reduce energy consumption. Source node transmits duplicated information relayed by distributed antennas called a virtual antenna array. Destination node combines that information to reduce packet error rate. The suggested cooperative scheme enhances the reliability by providing high diversity gains through intermediate relay nodes to overcome the distinct characteristics of the underwater channel, such as high transmission loss, propagation delay, and ambient noises. It is suggested that the algorithm select destinations and potential relays from a set of neighboring nodes that utilize distance cost, the residual energy of each node and local measurement of the channel conditions into calculation. Simulation results show that the proposed scheme reduces average energy consumption, response time, and increases packet delivery ratio compared with the SPF(Shortest Path First) and non-cooperative scheme using OPNET Moduler.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.5 s.347
• /
• pp.156-161
• /
• 2006

In this paper, GPS/IMT2000/Wireless LAN compact chip antenna is designed for mobile communication system. The proposed antenna size is $10.2mm{\times}21mm{\times}1mm$. It consists of three meander lines. dual resonance frequencies is achieved by two effective current paths using two meander lines and via. also The parasitic meander line structure is added. The coupling is adjusted by arranging parasitic meander line for triple-band. The fabricated antenna achieve triple-band. The resonance frequencies are 1.672GHz, 2.092GHz, 2.504GHz. The impedance bandwidths of each resonance frequencies are 156MHz, 272MHz, 64MHz. The maximum radiation gains of fabricated antenna are 0.08dBi, 1.67dBi, -1.44dBi. The proposed antenna achieve quasi monopole radiation pattern.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.3 no.1 s.4
• /
• pp.75-83
• /
• 2004

This paper describes the design, fabrication, and measurement of a low side lobe antenna for RSE base station of the ETCS which is one of the ITS services. The antenna is installed on the gantry of road side and provides the wireless communication lint between vehicles and RSE. The required characteristics of ETCS base station antenna are low sidelobe and specific beam pattern by the road and install environment and installed place of OBU. To minimize the affects of multipath signal by reflection, Circular polarization is required. To get low sidelobe of antenna, array configuration and weighting factor by Taylor distribution in radiator elements are applied. The measured results of fabricated antenna are as follows; return loss of 130MHz by -10dB, an axial ratio of 2.6dB, and a gain of 17dBi. It is found that the measured beam patterns are similar to design results.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.8
• /
• pp.890-895
• /
• 2016

As the wireless communication technique is developing rapidly, the use of smart devices is increasing. Due to gradually increasing data traffic, a new area, more than 6GHz of bandwidth to increase capacity of the network, has been studied. Millimeter Wave(MmWave) communications utilizes the bandwidth above 6GHz, which makes it possible to achieve one gigabit per second data rate. To overcome the path loss due to the smaller wavelength, the mass of the antenna arrangement is used. This paper presents an algorithm that maximizes the spectral efficiency of the system in the pre-coding process using a hybrid beamforming. Also it is suggested with the optimization of the number of beams that maximizes the spectral efficiency was maximized by the propose method.

• Journal of the Korean Ceramic Society
• /
• v.39 no.10
• /
• pp.1001-1006
• /
• 2002

Bond strength of $SrZrO_3$ resistive oxide barrier on Ag sheathed Bi(2223) tapes prepared by the sol-gel and dip-coating method was evaluated with an aid of Taguchi method and $L_18(2^1{\times}3^7)$ orthogonal arrays to determine the optimal process combination of levels of factors that best satisfy the bigger is better quality characteristic. The observed optimal condition is as follows: Sr/Zr mol ratio(0.3/0.7), amount of organic vehicle(5 wt%), drying temperature and time(160${\circ}C$, 10 min), heat treatment temperature and time(500${\circ}C$, 20 min), respectively. ANOVA analysis suggested that the influence of the factors within ${\alpha}$=0.1 was significant with a 90% confidence level.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.5
• /
• pp.527-535
• /
• 2003

In this paper, the performance of W-CDMA system with smart antenna is analyzed for angular spread in realistic wideband multipath channel. The realistic wideband channel is assumed, one of which is JTC channel model. And each multipath is assumed as a reflective wave from only one direction (only one cluster) in space. Several multipaths within one chip are distinguished into each one and the strongest signal is selected. As a result, the performance of the W-CDMA system with smart antenna in realistic wideband multipath channel has been considerably improved in proportion to the increase of angular spread.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.5
• /
• pp.343-354
• /
• 2020

Bi-stable mechanism is a system that has two different stable equilibrium positions within its range of motion. It has an ability to stay in two different positions without external power input and despite small disturbances. One of the most bi-stable applied mechanism is a morphing system, such as deployable structures, switch systems, and robot grippers. However, due to the complexity of mechanism and limitation of structure configuration, it is difficult to apply on a morphing system with rotating link mechanism. In this paper, an implementation method of rotational bi-stable mechanism using cylindrical permanent magnets is proposed. The magnetic field and the magnetic force were calculated from electromagnet model of the cylindrical permanent magnet. Based on the model, the force relation between two links containing the cylindrical permanent magnets was estimated. An array of cylindrical permanent magnets was selected for symmetric bi-stability, and an experiment on the link structure with the proposed bi-stable mechanism was performed to investigate the stability against a external torque.