• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.251-254
• /
• 2005

In this study vibration transmissibilities of the selected anti-vibration gloves were measured, and the measurement uncertainty was estimated. Since human factors such as palm size, gripping condition and dynamic properties of the hand-arm effect the measurement a lot, it is necessary to know ow much the uncertainty is. This study takes the measurement procedure suggested in ISO 10819. Three subjects Joined at each test and each anti-vibration glove was tested twice per a subject. Average and standard deviation of vibration transmissibility were calculated and uncertainty of them were estimated at 95% confidence level.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2002년도 동계 학술대회 논문집
• /
• pp.104-110
• /
• 2002

본 연구는 보행형 관리기의 손으로 전달되는 진동특성을 실험적으로 해석하고 평가하며 방진 방안을 제시할 목적으로 수행되었다. 관리기의 작업기 중에서 설문을 통해 사용 빈도가 높은 3개의 작업기(중경로터리, 중경제초기, 구굴기)를 선정하였고 각 작업기별 진동수준을 측정하였다. 진동 방지 방안에 대해서는 4개의 방진 장치(고무 패드, 방진 장갑, 핸들 방진 장치, 엔진 마운트)를 선정하여 각 방진 장치별 진동수준을 측정하였다. 방진 장치의 성능을 정확하게 비교하기 위해 진동의 측정은 진동수준이 가장 높은 구굴기에서 수행되었다. 실험결과에 의하면 관리기 작업이 작업자의 인체에 해를 끼칠 위험이 매우 크지만 이 결과는 작업자가 매일 3시간씩 관리기를 사용할 경우를 기준으로 설정한 값이기 때문에 실제로 관리기 사용일수가 많지 알은 대부분의 우리나라 사용자들에게 적용하는데는 한계가 있음을 밝힌다. 그렇다 하더라도 관리기의 주 사용자는 보행형 관리기 뿐만 아니라 보행형 경운기나 보행형 이앙기 등의 손으로 전달되는 진동이 심한 기계를 함께 사용하는 경우가 많음을 고려하면 방진 장치를 개발하거나 진동수준이 낮은 농작업기계를 개발하여 작업환경을 개선하는 조치가 필요하다고 생각한다. 그러므로 농작업기계에 대한 진동수준에 대한 종합적인 연구와 그에 대한 대책 마련이 지속적으로 수행되어야 할 것이다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2009년도 추계학술대회 논문집
• /
• pp.725-726
• /
• 2009

• 한국소음진동공학회논문집
• /
• 제16권6호
• /
• pp.602-608
• /
• 2006

In order to evaluate performance of anti-vibration gloves, it is necessary to measure the transmitted vibration to the hand and the applied forces at the same time while gripping the vibrating handle. In the study a system was developed to measure both the vibration and the forces. The system consists of a measurement handle with eight strain gauges and two accelerometers and a PC-based system with a software for signal processing and evaluation of the hand-transmitted vibration and for control of applied forces in the pre-determined range. The handle was installed on the vibration shaker which is strong enough so as not to be affected by dynamic coupling with the hand-arm system. Whole procedure of ISO 10819 to determine the vibration transmissibility of anti-vibration gloves was programmed into the system. As an example of the application, three subjects joined the test to get vibration transmissibilities of anti-vibration gloves where each glove was tested twice a subject. Average and standard deviation of vibration transmissibility were also calculated.

• 한국소음진동공학회논문집
• /
• 제19권2호
• /
• pp.217-224
• /
• 2009

This study aims to show the guideline to select optimal anti-vibration gloves for specific power tools to prevent hazardous vibration to human body. It is most desirable for the correct evaluation of handtransmitted vibration form the power tool handle to measure the acceleration between the handle surface and the hand palm as recommended in ISO 5349-1. First, the accurate acceleration measurement device was developed of which the thickness and weight were less than 6 mm and 12 g respectively so that it can be placed between the handle and the palm without any inconvenience during the measurement. Finally, using the device we estimated anti-vibration glove performances considering the frequency characteristics of generated vibration by the power tool.

• 산업경영시스템학회지
• /
• 제24권69호
• /
• pp.65-73
• /
• 2001

The objective of this study is to evaluate the vibration attenuation effects of the different type of gloves and drilling mode while operating a light-weighted powered hand drill. For the experimental design, five different kinds of glove(barehanded cotton partly coated anti-vibration, and open-finger vibration glove) two types of push force level(100N and 200N) and two types of drilling mode(impact and non-impulsive) were considered. Six healthy male subjects were employed to drive screws into a vertically mounted marble plate with a powered hand drill in a randomly ordered experimental conditions. The findings of this study are summarized as follows; (1) It was found that the best combination of overall BMS transmissibility was using impact drilling mode with anti-vibration glove among evaluated experimental conditions (2) The wearing open finger vibration glove in mid-frequency level and anti-vibration glove with impact drill in high-frequency were the best in the result from mean corrected transmissibility equation of ISO 10819.

• 한국산업보건학회지
• /
• 제18권1호
• /
• pp.1-10
• /
• 2008

In order to evaluate performance of anti-vibration gloves, it is necessary to measure the transmitted vibration to the hand and the applied forces at the same time while gripping the vibrating handle. In the study a system was developed to measure both the vibration and the forces. The system consists of a measurement handle with eight strain gauges and two accelerometers and a PC-based system with a software for signal processing, evaluation of the hand-transmitted vibration and for control of applied forces in the pre-determined range. The handle was installed on the vibration shaker which is strong enough so as not to be affected by dynamic coupling with the hand-arm. Whole procedure of ISO 10819:1996 to determine the vibration transmissibility of anti-vibration gloves was programmed into the system. As an example of the application, three subjects joined the test to get vibration transmissibilities of 9 anti-vibration gloves where each glove was tested twice a subject. Average and standard deviation of the corrected vibration transmissibility were also calculated. All tested gloves fulfilled criterion for M-spectrum($\overline{TR_M}$<1.0), but one glove fulfilled criterion for H-spectrum($\overline{TR_H}$<6.0),