• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.10
• /
• pp.2273-2280
• /
• 2013

This article introduces the next-generation air surveillance system and investigates how to design of front-end low noise amplifier of the ground station receiver. In consideration of the international standard documentation and the performance of existing products, the study conducts the link budget on the entire system so that it can be competitive in terms of receive sensitivity or reliability. To obtain a proper low noise amplifier, standards of design are decided so that such factors as gain, gain flatness, and reflective loss can be optimal. In its design, the bias circuit appropriate for the characteristics of low power, low noise, or high gain was built, and according to the results of the simulation conducted after the optimal design, its gain was 16.24dB, noise factor was 0.36dB, input-output reflective loss was -18dB and -28dB each, and frequency stability was 1.11. According to the results measured after the design, its gain was 17dB, noise factor was 0.51dB, gain flatness was 0.23dB, and input-output reflective loss was -18.28dB and -24.50dB each, so the results gained were suitable for building the overall system.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.31 no.6_1
• /
• pp.463-469
• /
• 2013

In addition to the VRS-RTK service, FKP-RTK service launched recently in Korea however unlike VRS, it is not yet applied to various surveying tasks. VRS system is operated in two way communication over the mobile Internet. When user send rover position data to network RTK server and the server provides correction data to users continuously. It causes to increase communications load and makes delaying or failure in data transmission depends on server capacity and number of concurrent users. In contrast, since FKP system is one way communication system, user only receives correction data and area correction parameters for the selected Continuous Reference Station from the server. Thus, there is no limitation to the number of concurrent users in FKP system and it would be more efficient than VRS system in terms of economic. To this end, we performed FKP-RTK test for Unified Control Points and Urban Control Points where are located at 5 regions in Korea to evaluate the accuracy. As a result, almost of FKP positioning data are in error range of ${\pm}6.2cm$ in horizontal and it would be enough for construction survey such as for earth work in limited except precise structure survey.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.3A
• /
• pp.209-216
• /
• 2005

This paper generally relates to the field of wireless local area networks(WLANs), and more particularly, to AP selection and association methods for the performance of a station. In these days, IEEE 802.11 Wireless LAN network is widely deployed and used as an emerging service to connect high-speed Internet in the public wireless environment. But, if there are many users in hot spot area, they suffer a severe decrease of performance. Thus it needs an association and access control mechanism especially when it is used in the public environment. In this paper, we suggest a selection and association method using Beacon or Probe Response frames based IEEE 802.11. Station selects AP using the information of the capacity area in a Beacon or a Probe Response frame. According to the present paper, an association method for a public WLAN service, which includes a WLAN user terminal and an AP for relaying WLAN communications to and from the user terminal, includes the steps of the user terminal asking the AP's states for access to a radio channel; and the station selects and associates with the AP According to the above-described selection in a high speed wireless Internet service based on public WLAN technologies that are currently in operations. Further, it is possible to improve the efficiency of network management.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.11
• /
• pp.711-717
• /
• 2017

The railway is a public transportation system that provides large-scale passenger transportation and service, whose reliability and safety is the top priority. The wiring of railway vehicles is classified into train control lines (train lines) and communication lines. The train lines are used for input / output signals related to vehicle driving and safety functions, and the communication lines are used for the input / output signals for passenger services such as broadcasting. In order to measure the reliability of railway vehicles, a train line is applied to the input / output interface of the control signals between the electric control devices in the vehicle, and there are many electromechanical devices such as relays and contactors for the control logic. In fact, since the vehicle control circuit is composed of several thousand contacts, it is difficult to check for errors such as contact failure, and it is impossible to check the real-time status, so a lot of manpower and time is required for regular maintenance. Therefore, we analyze the current state of the train line design of the electric equipment used for driving and services in domestic railway cars and propose three wiring reduction methods to improve it. Based on the analysis of domestic electric vehicles, it was confirmed that the wiring reduction effect is 35% or more.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.3
• /
• pp.697-707
• /
• 2015

This paper covered the design and implementation of the demodulation receiver in the ADS-B 1090ES system, which is one of the CNS/ATM's surveillance systems. This researched demodulation performed at the level required by RTCA DO-268B and EUROCAE ED-129. The single signal process method, which applies a baseline multi-sample technique among multi-amplitude sample demodulations, was suggested to improve the quality of the receiver signal, the dynamic range and so on. The suggested multi-signal level tuning method has enhanced the single-signal process method, reducing the unstable reception ratio by the transmit output level difference and manufacturing receiver hardware. The result was that the receiver suggested by the method had 0~87dBm in dynamic range and -90dBm in MTL. This shows a better performance by -3dBm less than the international standard in ADS-B 1090ES ground receiver equipment. The systems which use a similar modulation method, will be considered to be widely applied.

• Journal of Satellite, Information and Communications
• /
• v.2 no.2
• /
• pp.22-28
• /
• 2007

Spectrum spreading, in its general form, can be conceived as an artificial expansion of the signal bandwidth with respect to the minimum Nyquist band required to transmit the desired information. Spreading can be functional to several objectives, including resilience to interference and jammers and reduction of power spectral density levels. In the paper, signal spreading is manly used for increasing the received energy, thus satisfying link budget constraints, for terminals with low aperture antennas, without increasing the transmitted EIRP. As a matter of fact, in many mobile scenarios, even when MODCOD configurations with very low spectral efficiency (i.e. QPSK-1/4) in DVB-S2 standard, are used, the link budget cannot be closed. Spectrum spreading has been recently proposed as a technique to improve system performance without introducing additional MODCOD configurations under the constraint of fixed power spectrum density level at the transmitter side. To this aim, the design of spectrum spreading techniques shall keep into consideration requirements such as spectrum mask, physical layer performance, link budget, hardware reuse, robustness, complexity, and backward compliance with existing commercial equipments. The proposed implementation allows to fully reuse the standard DVB-S2 circuitry and is inserted as an 'inner layer' in the standard DVB-S2 chain.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.1
• /
• pp.42-52
• /
• 2017

DASH (Dynamic Adaptive Streaming over HTTP) is an adaptive streaming technique that enables transmission of multimedia content when clients request the multimedia contents to server. In this system, to ensure the best quality of the content to satisfy users, it is necessary to precisely measure the residual bandwidth. However, the measured residual bandwidth by the DASH, which is not considering the transmission features of TCP, varies by the size of previous media segment, which makes it hard to ensure QoE to users. In this paper, we excluded the TCP Slow start range from measurement of residual bandwidth and suggested the new DASH bandwidth measuring method to decrease the error. Then, we realized the method in DASH system based on open source, and compared the existing measuring method. The new method showed that the accuracy of result has increased by 20%. Also, it could improve the QoE of users in terms of service quality and number of changes of segment quality.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.1
• /
• pp.51-62
• /
• 2002

EMI/EMS 측정을 위해서는 주변 전자파 잡음(background noise)이 낮은 야외시험장(Open Area Test Site)이 가장 바람직하나, 근래 전자(전기 기기 사용의 증가와 방송.무선통신 시스템의 다양화로 인한 인공잡음(artificial noise)의 증대로 조건에 부합된 부지 선정이 어렵고, 설치 비용이 매우 크며 날씨 변화에 따라 시험 계획이 변경 될 수도 있는 단점이 있다. 전자파 분-무반사실(Semi Anechoic Chamber)은 대부분의 환경 잡음을 감쇠시키므로 야외시험장처럼 장소의 구애를 받지 않아 도시나 혹은 제품 생산지 가까이에 설치 운용이 가능하다. 그러나 큰 설치 공간과 많은 시설 유지 비용을 필요로 하며, 저주파 대역에서는 반사에 의한 공진을 완전히 제거할 수 없어 성능이 떨어진다. 또한, 최근 컴퓨터 CPU의 동작주파수가 급속하게 높아지고 PCS, IMT-2000 등과 같은 이동전화의 사용주파수도 계속해서 높아짐에 다라 미연방통신위원회(Federal Communication Commission)에서는 5㎓까지의 복사 방출 시험을 요구하고 있다. IEC 61000-4-3 복사 내성 시험규격도 휴대폰 주파수인 2㎓까지 확장되었으며 IMT-2000, Bluetooth 등 새로운 이동통신서비스가 속속 개발됨에 따라 18㎓ 까지 시험 주파수가 확장되는 추세이다. 그러나, 현재 국내 각 연구실에서 보유하고 있는 야외시험장이나 전자파 반-무반사실의 경우 1㎓이상에서의 시험이 곤란하여 수 ㎓주파수대역에서 시험이 가능한 복사 및 내성시험 시설이 필요하게 되었다. 이러한 문제점들을 해결하기 위해 고안된 대용 측정 시설 중 대표적인 것이 TEM 셀이나 GTEM셀과 같은 TEM 도파관(waveguide) 형태의 장비들이다. 이들은 본래 EMS 측정을 위한 장비이지만 협소한 공간이나 외부와의 전자파 간섭의 우려가 없고, 설치가 비교적 자유로워 여러 연구기관에서 도파관 원리를 이용한 측정 방식을 연구(개발하여 범용적인 전자파 적합성 측정 장비로서 활용하고 있다. 야외시험장과 무반사실 등이 안테나에 의한 피시험기기 주변 공간에서의 1점 측정으로 인해 시험 시간이 많아 소요되는 공통적인 단점이 있는 반면, TEM 도파관에 의한 측정은 일단 피시험기기의 모델링 정보만 얻어지면 계산에 의해 EMI 측정을 바로 할 수 있다. <표 1>에서 현재 상용화되어 사용되고 있는 TEM/GTEM 셀, 야외 시험장 및 전자파 무반사실에 대해 EMI 측정과 관련된 몇 가지 사안에 대해 비교하였다. 본 문서에서는 야외시험장이나 전자파 반-무반사실 등과 같은 기존 EMI/EMS 측정 시설의 단점을 보완하고, 광대역 특성을 갖는 대용 측정 시설로서의 TEM 도파관에 대해 소개하고 야외시험장 결과와의 상관관계 알고리즘 및 표준화 동향에 대해 기술하였다. 2절에서는 대표적인 TEM 도파관 구조의 측정 시설인 TEM 셀과 GTEM 셀의 전기적.구조적 특징에 대해 간단히 기술하고, 3절에서는 TEM 셀과 GTEM 셀에서이 측정결과를 이용하여 야외 시험장 결과를 얻어내는 상관관계 알고리즘에 대해 기술하였다. 4절에서는 IEC/CISPR와 TC77에서의 표준화 활동을 중심으로 현재 진행중인 TEM 도파관 관련 표준화 동향과 내용에 대해 기술하고자 한다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.5A
• /
• pp.482-489
• /
• 2010

In this paper we have proposed a new architecture of DQ-IRM(Double-Quadrature Image Rejection Mixer) for image rejection in the low-IF receiver. It consist of a frequency-tunable RF PPF(Poly Phase Filter) and the quadrature mixers. The conventional DQ-IRM generates the quadrature RF signals for the RF wide band at once. But the proposed DQ-IRM with the frequency-tuable RF PPF generates the quadrature RF signals for the narrow band of 2~3 channels bandwidth, which is partitioned from the RF wide band. We designed the CMOS RF tuner for T-DMB(Terrestrial Digital Multimedia Broadcasting) with the proposed 3rd DQ-IRM using a 0.18um CMOS technology and verified the performances of the designed receiver such as the image rejection ratio, the noise figure and the power consumption. The overall NF of the RF tuner is about 1.26 dB and the image reject ratio is about 51 dB. The power consumption is 55.8 mW at 1.8 V supply voltage. The chip area is $3.0{\times}2.5mm^2$.

• Journal of KIISE:Information Networking
• /
• v.33 no.4
• /
• pp.333-342
• /
• 2006

The cdma2000 lxEV - DO mobile communication system provides broadcast and multicast services (BCMCS) to meet an increasing demand from multimedia data services. The servicing of video streams over a BCMCS network must, however, face a challenge from the unreliable and error-prone nature of the radio channel. The BCMCS network uses Reed-Solomon coding integrated with the MAC protocol for error recovery. We analyze this coding technique and show that it is not effective in the case of slowly moving mobiles. To improve the playback quality of an MPEG-4 FGS video stream, we propose the Hybrid error recovery scheme, which combines Reed-Solomon with ARQ, using slots which are saved by reducing the Reed-Solomon coding overhead. The target packets to be retransmitted are prioritized by a utility function to reduce the packet error rate in the application layer within a fixed retransmission budget. This is achieved by considering of the map of the error control block at each mobile node. The proposed Hybrid error recovery scheme also uses the characteristics of MPEG-4 FGS (fine granularity scalability) to improve the video quality even when conditions are adverse: slow-moving nodes and a high error rate in the physical channel.