• Journal of the Korean Recycled Construction Resources Institute
• /
• v.10 no.1
• /
• pp.74-79
• /
• 2022

In this study, the effect of a sudden decrease in internal humidity and a decrease in hydration level due to the tight internal structure of high-strength concrete and cement composites was investigated. To verify the change in the internal Si hydration, waste glass foam beads were used as a lightweight aggregate, and the internal unreacted hydrate reduction and hydrate formation tendency were identified over the mid- to long-term. Waste glass foam beads were mixed with 5, 10, and 20 %, and were used by pre-wetting. As the mixing rate of the waste glass foamed beads increased, the strength showed a tendency to decrease. In addition, when the mixing amount of pre-wetted waste glass foam beads increases inside through XRD analysis, TGA analysis, and Si NMR analysis, it is judged that the hydration degree of internal Si is different because moisture is supplied to the paste.

• Journal of Adhesion and Interface
• /
• v.19 no.2
• /
• pp.68-73
• /
• 2018

In this study, conductive EVA foams including multi-wall carbon nanotubes (MWCNT), glass beads were prepared. The electrical conductivity and physical properties of the foams were confirmed with varying amount of MWCNT, mixing time, and amount of glass beads. The electrical conductivity increased with the amount of MWCNT. Dispersity of MWCNT in EVA foams were improved with glass beads. It can be suggested that conductive EVA foams can be successfully prepared with improved dispersity of MWCNT in ethylene-vinyl acetate by using glass beads.

• Journal of the Korea Institute of Building Construction
• /
• v.17 no.5
• /
• pp.393-401
• /
• 2017

This study presents an evaluation of basic properties of light weight mortar with expanded polystyrene bead(EPB) and waste expanded polystyrene(WEP) by varying replacement rations. In order to evaluate the basic properties of the light weight mortar with EPB and WEP, unit weight, compressive strength, flexural strength, water absorption ratio, thermal conductivity and distribution of polystyrene (EPB and WEP) in hardened mortar were performed. As a result, unit volume, compressive strength, bending strength, water absorption and thermal conductivity of light weight mortar were increased, but area distribution of polystyrene decreased with increasing the replacement ratio of WEP.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2023.05a
• /
• pp.125-126
• /
• 2023

Recently, heat island and dry island phenomena occur frequently due to land surface development and excessive energy consumption in urban areas. As a result, the surface temperature of the building and the entire temperature of its surroundings are increased, and as a result, the durability of the building is rapidly deteriorated. In order to suppress these causes, a method of maintaining the temperature of road heating wires was implemented as a temporary measure, but this did not predict climate change. Therefore, this study is a method to measure the compressive strength, density, and thermal conductivity of lightweight concrete using waste glass foam beads. After fabricating a simple chamber, the temperature and humidity of the inside and outside were measured with an Arduino device in consideration of external factors. Therefore, if waste glass foam beads made through proper mixing are constructed in the urban center, the quality of the urban can be improved.

• Journal of the Korea Institute of Building Construction
• /
• v.23 no.5
• /
• pp.527-536
• /
• 2023

This research embarked on a comprehensive examination of the engineering characteristics of lightweight concrete intended for implementation in rhamen-type modular building walls. The concrete was formulated utilizing bottom ash and coated EPS beads, in accordance with the Korea Construction Standards Center(KCS) 14 20 20 "Lightweight Aggregate Concrete". Our findings articulate that while EPS beads tend to diminish the compressive strength of the lightweight concrete, they concurrently contribute to a notable reduction in unit mass. The porous nature of the bottom ash endows the material with diminished thermal conductivity. Significantly, a mixture containing 50% EPS beads and 50% BA20 aggregates, replacing half of the coarse aggregates, was found to meet the standard specifications.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.1
• /
• pp.96-101
• /
• 2011

Under extreme test or operation condition, refrigerator endures complicated stresses state and thermal bowing deformation arises on the sidewall. Shelf rails designed in the inner case provide increased surface area to permit expansion without bowing, and also increase structural rigidity to resist bowing. In this study, we designed six different shelf patterns of refrigerator model and studied the bead on refrigerator deformation using finite element method (FEM). Analysis result shows that increasing the numbers of beads properly in refrigerator is more helpful to reduce thermal bowing deformation. In addition, the beads would decrease stress on refrigerator sidewall. However, vertical beads have no effect to reduce thermal deformation of the bowing.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.05a
• /
• pp.21-22
• /
• 2018

Foamed concrete is a porous concrete that is cured by mixing bubbles into cement slurry. It is lighter than ordinary concrete and is characterized by higher insulation. Lightweight foamed concerte is mainly used as a sandwich panel in Korea, and is also used as a refractory filler in fireproof safes. Studies on lightwight foamed concrete have been carried out on strength,density and thermal conductivity. However, it is confirmed that the research on the fire resistance performance is very limited. Based on this study, fire resistance of lightweight foamed concrete using expanded polystyrene beads is investigated.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.1046-1050
• /
• 2005

Micro Cellular Plastics create a sensation at polymer industrial for lowering product cost & overcoming a lowering of mechanical intensity. There Is much development from injection molding pans but Extrusion parts is slow. This research is MCPs Extrusion parts, It is basis experiment for Process to make beads that is basis raw material of Package used most by shock mitigative of industry.

• Fire Science and Engineering
• /
• v.16 no.4
• /
• pp.77-84
• /
• 2002

In this paper, we had analyzed comsbustion gases using a GASTEC colorimetric gas detector tube according to the method of NES 713 in order to combustion gases toxicity evaluation for beads polystyrene foam, extruded polystyrene foam, rigid polyurethane foam, flexible polyurethane foam, flexible polyvinyl chloride pipe, vinyl floor cover, polyethyelene foam(flame retardant untreated) and polyethyelene foam (flame retardant treated) of plastics material. As results of gas analyses by using this method, comsbustion gases producted from small specimens of plastics material had reached fatal to man at 30 minutes exposure time that had possesed toxicity index of more than 1. Toxicity indexes of each specimen were estimated range of 4.3∼179.2, flexible polyvinyl chloride showed the hightest toxicity index at 179.2, and beads polystyrene foams showed the lowest toxicity index at 4.3.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2023.11a
• /
• pp.51-52
• /
• 2023

Recently, heat island and dry island phenomena occur frequently due to land surface development and excessive energy consumption in urban areas. As a result, the surface temperature of the building and the entire temperature of its surroundings are increased, and as a result, the durability of the building is rapidly deteriorated. In order to suppress these causes, a method of maintaining the temperature of road heating wires was implemented as a temporary measure, but this did not predict climate change. Therefore, this study is a method to measure the compressive strength, density, and thermal conductivity of light weight concrete using waste glass foam beads. After fabricating a simple chamber, the temperature and humidity of the inside and outside were measured with an Arduino device in consideration of external factors. Therefore, if waste glass foam beads made through proper mixing are constructed in the urban center, the quality of the urban can be improved.