• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.8
• /
• pp.683-691
• /
• 2015

Circulating Fluidized Bed(CFB) combustion has the several advantages which are the fuel flexibility, the economy, the efficiency and the environment. It is necessary to apply a renewable energy to produce electricity due to the Renewable Portfolio Standard(RPS) mandates recently. So, in this study, co-combustion with a coal and a wood pellet was investigated to evaluate the combustibility and the environment as function of blending ratio of them in a Lab-scale CFB reactor. To investigate the characteristics of the co-combustion, the blending ratio which is the weight of wood pellet by the total calorific value of the supplied, was considered. Bed material was a river sand(No. 7). As increasing the blending ratio, the exhausted gas emissions such as CO, NOx, HC and SOx were decreased. But in case of wood pellet over 30%, CO, HC and SOx emission were increased. And the gas temperatures at the downstream were decreased.

• Clean Technology
• /
• v.23 no.4
• /
• pp.364-377
• /
• 2017

In this study, to improve the low surface area of domestic anthracite as raw materials of activated carbon, characteristics on chemical activation and VOCs adsorption of activated carbon according to mixing ratio of anthracite and lignite. For these, properties of raw materials, parameter characteristics of preparation processes for activated carbon, and VOCs adsorption characteristic of the prepared activated carbon are analyzed. The experimental results showed that, the domestic anthracite had disadvantages of high contents for ash and lead, arsenic, which were exceeded for the heavy metal limits, in the properties of raw materials. To improve these diadvantages, using the mixing ratio of anthracite and lignite, and the optimum conditions for pretreatment, activation, washing, and pellitization process, the activated carbon had a range of BET (Brunauer-Emmett-Teller) surface area of $1,154{\sim}1,420m^2g^{-1}$ with mesopore development and hydrophobic surface property. The carbons were satisfied with the quality standard for granular activated carbon, and had similar physicochemical properties with the commercial activated carbon. The minimum mixing condition for commercial VOCs activated carbon performance must have the caloric value of above $5,640kcal\;kg^{-1}$, and the carbon had higher adsorption capacity with order of xylene > toluene > benzene according to more higher molcular weight and hydrophobic property.

• Journal of Conservation Science
• /
• v.32 no.4
• /
• pp.549-560
• /
• 2016

The purpose of this study is to identify the material characteristics of blackwares excavated from the Bonggok kiln site in Jinan-gun, Jeollabuk-do Province, South Korea, by scientific analyses and a reproduction experiment. Scientific analyses were conducted to determine the physical properties, chemical composition and for microscopic observation of blackwares. A reproduction experiment was also conducted by producing ceramic samples with black glaze, red ocher and limestone, and then cross sections of the samples were observed. The analysis results showed that all the excavated blackwares have similar properties such as chromaticity, specific gravity, absorption factor and porosity, but there is a difference depending on the crystallization of the ceramics. Thermal analysis showed that the exothermic peak was observed at about $1200^{\circ}C$, and crystal structure analysis indicated the presence of mullite. Hence, it can be concluded that the firing temperature of the excavated blackwares was around $1100-1200^{\circ}C$. Moreover, the glaze present on these blackwares has about 22% higher $Fe_2O_3$ content than those excavated from other places; however, the former has lower CaO content. For the reproduction experiment, samples were made using limestone as a flux and red ocher as a glaze. The results show that the cross section of the glaze layer of the reproduced sample have iron crystals with dendritic structures, similar to those present in the excavated black-wares. It is assumed that such iron crystals were formed during the process of melting and solidification of the iron oxide present in the blackwares.

• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.3
• /
• pp.220-225
• /
• 2013

The adsorption characteristics of phenol by the powdered activated carbon (PAC) were investigated by series of batch experiments. The pseudo-second-order model described the adsorption kinetics adequately with correlation coefficients over 0.999, indicating chemical adsorption as the rate-limiting step. The kinetic rate constants were from 0.55 to 19.81 mg $mg^{-1}min^{-1}$. The adsorption isotherm followed the Langmuir isotherm, indicating the homogeneous mono-layer adsorption onto the surface of the adsorbent. The values of activation energy, enthalpy and entropy were 17.44 kJ $mol^{-1}$, -8.26 kJ $mol^{-1}$ and -18.94 J $mol^{-1}K^{-1}$, respectively. The Gibbs free energy was in the range of -2.89~-2.14 kJ $mol^{-1}$. The results show that the phenol adsorption is physical, spontaneous and exothermic reaction.

• Clean Technology
• /
• v.22 no.4
• /
• pp.286-291
• /
• 2016

In this study we made fuel pellet from miscanthus biomass and investigated changes of physiological characteristics and electricity consumption of pelletizing process in comparison with fuel pellet made of pine sawdust. We also examined combustion characteristics including ash content and clinker forming ratio with fuel pellet made of mixing with micanthus biomass and lime powder. Bulk density of ground-miscanthus and pine sawdust were $158g\;L^{-1}$ and $187g\;L^{-1}$, respectively. Bulk density of ground miscanthus was lower than that of pine sawdust, but increased to $653g\;L^{-1}$ after pelletizing, which was similar to $656g\;L^{-1}$ of pine sawdust pellet. Moisture content in raw miscanthus and ground miscanthus were 17.0% and 11.8%, respectively. Moisture content in ground miscanthus was similar to that of pine saw dust and decreased to 6.73% after pelletizing, which was 7.7% lower than that of pine sawdust pellet. Although $27kWh\;ton^{-1}$ were required for compaction press that was an additional process in miscanthus pelleitizing, total required electricity was $193kWh\;ton^{-1}$ which was similar to $195kWh\;ton^{-1}$ of pine sawdust pellet pelleitizing. Pellet durability and pelletizing ratio of miscanthus were 98.0% and 99.7%, respectively, which were similar to 98.1% and 99.4% of pine sawdust pellet. When lime mixing ratio increased, ash melting degree and clinker forming ratio of miscanthus pellet increased. While higher heating value and clinker forming ratio of miscanthus pellet decreased.

• Journal of the Korean Electrochemical Society
• /
• v.2 no.4
• /
• pp.218-220
• /
• 1999

The performance of the Electric Vehicle and Hybrid Electric Vehicle depends on that of the battery pack composed of series connected batteries. And thermal property is one of the main factors which decide the performance of the battery pack. So heat generation rate from the battery under the various driving mode must be measured as precise as possible because thermal characteristics of the battery affect the driving performance and battery pack's life cycle. Besides, to design and develop the battery thermal management system for the EV and HEV, the measurements of the thermal properties of the batteries are needed. However, the established calorimeter is not adequate to test an EV's battery because its cavity is too small to accommodate the EV's battery. Therefore we developed the calorimeter to test the thermal property of the EV's battery. Its cavity size is 120mm long, 75mm wide and 200mm high. The calorimeter is calibrated by the dummy cell which generates the heat rate from zero to 200W. The measuring accuracy of the calorimeter is within $2\%$ and its voltage stability is 2.5mV in the constant temperature bath.

• Applied Chemistry for Engineering
• /
• v.25 no.1
• /
• pp.103-106
• /
• 2014

Recycling of bottom ash from municipal solid waste (MSW) incinerator has been strictly limited due to its composition of high level chlorine and other unfavorable substances. The composition of MSW has been, however, changed after the introduction of garbage-bag sales system, extended producer responsibility (EPR) policy and the prohibition of direct landfill of food waste. Recent waste shows reduced moisture and chlorine content, increased calorific value due to the separation of food waste, incombustible materials and PVC. The main purpose of this study is to investigate the trend of composition changes of MSW incinerator bottom ash and to compare the analytical results with those before the separation system was introduced. CaO content of bottom ash, one of the major component of cement clinker, increased from 26.7% in 2001 to 34.0% in 2006. The chlorine content showed a dramatic decrease from 1.84% in 2001 to 0.00655% in 2006, which is closely compatible with that of the fly ash of coal-utilizing thermal power plants, which is mainly due to the changes of MSW composition. It is eventually considered that there is a possibility of utilizing the incinerator bottom ash as a raw material of cement clinker feed substances.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.4
• /
• pp.639-647
• /
• 2019

Recently, as the semiconductor integration technology due to miniaturization and high density of electronic equipment have developed, it is importantly recognized the application of thermal control system in order to release inner heat generated from chips, modules, In this study, we considered the heat transfer and pressure drop characteristics in a horizontal channel with four blocks using k-${\omega}$ SST turbulence model During CFD (Computational Fluid Dynamics) analysis, the parameters applied block width, block height, heat source and turbulence generator placement etc. As the boundary conditions of analysis, the channel inlet temperature and flow velocity were respectively 300 K and 3.84 m/s, the heat flux was $358W/m^2$. As a result, the heat transfer performance was decreased as the block width ratio (w/h) was increased, while it was increased as the block height ratio (h/w) was increased. In addition, as the arrangement of heat source size was increased to high heat flux from low heat flux, it was influenced by heat source size and the heat transfer coefficient showed a tendency to increase, When the turbulence generator was installed in the upper part of block No. 1 position the closely to the channel entrance, the heat transfer characteristics was greatly influenced on the whole of four heating blocks. and in oder to consider the pressure drop characteristics, we are able to select the most appropriate turbulence generator's position.

• Clinical and Experimental Pediatrics
• /
• v.48 no.4
• /
• pp.438-442
• /
• 2005

Kawasaki disease is an acute febrile vasculitis that occurs predominantly in young children under 5-years-old. The patients present generally with a high spiking fever that is unresponsive to antibiotics and lasts for more than five days at least. Prolonged fever has been shown to be a risk factor in the development of coronary artery disease. It seems to be certain that infectious agents are associated with the pathogenesis of Kawasaki disease. The differential diagnosis of Kawasaki disease must rule out infectious diseases including scarlet fever, toxic shock syndrome, measles, and so on. This is very important for adequate treatment and prevention of cardiac complications of Kawasaki disease. We experienced a 25-month-old boy who had high fever and pneumonic consolidation in the right middle and lower lobe of the lung that was considered as mycoplasma pneumonia on admission and developed coronary artery aneurysmal dilatation during treatment with roxythromycin.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.4
• /
• pp.375-381
• /
• 2010

In this paper, the heat-transfer characteristics of steam reforming in an annular reactor are presented. Heat is supplied by the catalytic combustion of syn-gas. The thermal behaviors of exothermic and endothermic reactions in a directly coupled concentric-tube packed-bed reactor were investigated experimentally. The gas mixture supplied for catalytic combustion consisted of the off-gas emitted from MCFC anode. Methane in steam at a suitable S/C (steam-to-carbon) ratio was used in the reforming reactions. On the basis of the experimental results, a simple simulation was performed to predict the temperature profile required in the reforming side of the reactor to achieve optimum hydrogen yield. The results of this study may be utilized as reference data in future studies for further development of coupled reactors.