• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.11
• /
• pp.1102-1110
• /
• 2008

This research was performed to analyze the characteristics of wood wastes from origin and to suggest grade-classification for them. Korean proximate analysis was conducted, and heating value, heavy metals and Cl concentrations were analyzed for gradeclassification. Wood wastes were sampled from forest, living, construction and demolition, and industrial areas with origin. Moisture content of most wood wastes was ranged in 5$\sim$10%. VS (volatile solids) and ash contents of them showed > 95% and < 5%, respectively. Most wood wastes except wood for growing mushroom permitted the standard (low heating value $\geq$ 3,500 kcal/kg) for refusederived fuel. CCA (Cr, Cu, As) concentration of wood wastes used in bench, wasted fishing boat, and railroad crosstie was higher than that of the other ones. Cl content showed approximately 1.3% in wood box for fish and $\leq$ 0.2% in the other wood wastes. Cl content of all wood wasted used in this research permitted the standard (Cl $\leq$ 0.2%, dry weight basis) for refuse-derived fuel. If the wood wastes were classified in 3-grade, plywoods would be in 2nd grade, and MDF (medium density fiber), wooden bench, painted electric wire drum, wasted fishing boat, and railroad crosstie be in 3rd grade.

• Journal of the Korean Applied Science and Technology
• /
• v.32 no.1
• /
• pp.148-156
• /
• 2015

In this study the differences in the sample size and sample input changes as characteristics of bio-oil oak(Quercus variabilis), the oak 0.5~2.0 mm of the oak weighing 300~900g was processed into bio-oil via fast pyrolysis for 1.64 seconds. In this study, the physico-chemical properties of biooil using oak were investigated. Fast pyrolysis was adopted to increase the bio-oil yield from raw material. Although the differences in sample size and sample input changes in the yield of pyrolysis products were not significantly noticeable, increases in the yield of bio-oil accounted for approximately 60.3 to 62.1%, in the order of non-condensed gas, and biochar. When the primary bio-oil obtained by the condensation of the cooling tube and the seconary bio-oil obtained from the electric dust collector were measured separately, the yield of primary bio-oil was twice as higher than that of the secondary bio-oil. However, HHV (Higher Heating Value) of the secondary bio-oil was approximately twice as higher than that of the primary bio-oil by up to 5,602 kcal/kg. The water content of the primary bio-oil was more than 20% of the moisture content of the secondary bio-oil, which was 10% or less. In addition, the result of the elemental analysis regarding the secondary bio-oil, its primary carbon content was higher than that of the primary bio-oil, and since the oxygen content is low, the water content as well as elemental composition are believed to have an effect on the calorific value. The higher the storage temperature or the longer the storage period, the degree of the viscosity of the secondary bio-oil was higher than that of the primary bio-oil. This can be the attributed to the chemical bond between the polymeric bio-oil that forms during the storage period.

• Journal of the Mineralogical Society of Korea
• /
• v.22 no.3
• /
• pp.241-248
• /
• 2009

Kaolinite was synthesized from amorphous $SiO_2$ and $Al(OH)_3{\cdot}xH_{2}O$ as starting materials by hydrothermal reaction conducted at $250^{\circ}C$ and $30\;kg/cm^2$. The acidity of the solution was adjusted at pH 2. The synthesized kaolinite was characterized by XRD, IR, NMR, FE-SEM, TEM and EDS to clarify the formational process according to the reaction time from 2 to 36 hours. X-ray diffraction patterns showed after 2 h of reaction time, the starting material amorphous $Al(OH)_3{\cdot}xH_{2}O$ transformed to boehmite (AlOOH) and after the reaction time 5 h, the peaks of boehmite were observed to be absent thereby indicating the crystal structure is partially destructed. Kaolinite formation was identified in the product obtained after 10 h of reaction and the peak intensity of kaolinite increased further with reaction time. The results of TGA and DTA revealed that the principal feature of kaolinite trace are well resolved. TGA results showed 13 wt% amount of weight loss and DTA analysis showed that exothermic peak of boehmite observed at $258^{\circ}C$ was decreased gradually and after 10 h of reaction time, it was disappeared. After 5 h of the reaction time, the exothermicpeak of transformation to spinel phase was observed and the peak intensiy increased with reaction time. The results of FT-IR suggested a highly ordered kaolinite was obtained after 36 hours of reaction. It was identified by the characteristic hydroxide group bands positioned at 3,696, 3670, 3653 and $3620\;cm^{-1}$. The development of the hydroxyl stretching between 3696 and $3620\;cm^{-1}$, depends on the degree of order and crystalline perfection. TEM results showed that after 15 h reaction time, curved platy kaolinite was observed as growing of (001) plane and after 36 h, the morphology of synthetic kaolinite exhibited platy crystal with partial polygonal outlines.

• Asian Journal of Turfgrass Science
• /
• v.23 no.2
• /
• pp.229-240
• /
• 2009

The high temperature and water content in soil profile probably affect the physiological disorder especially on cool-season turfgrasses in warm and humid weather of Korean summer. The purpose of this research was to analyze the effect of soil temperature and water content on the growth and stress response of creeping bentgrass(Agrostis palustris Huds.) under a humid and warm temperature. USGA(United State of Golf Association) green profile in laboratory test, Daily temperature changes were tested under a dried sand, 70% water content of field capacity, and saturated condition at $34^{\circ}C$ of the USGA green in lab. In this test, the dried sand reached to $80^{\circ}C$, however, the surface temperature decrease of $10^{\circ}C$ on the saturated condition. In the thermal properties test in field, thermal conductivity, thermal diffusivity, and soil temperature were increased followed by irrigation practise. In the water-deficient condition, the highest soil temperature was reached temporally right after irrigation, however, the excessive soil water content higher than field water holding capacity showed the highest soil temperature after a while. This result indicated that a heat damage to root system was caused from the thermal conductivity of a high surface soil temperature. The excessive irrigation when a high turf surface temperature should occur a negative result on tufgrass growth, moreover, it would be fatal to root growth of creeping bentgrass, especially when associated with a poor draining system on USGA sand green. Overall, this study shows that high soil temperature with water-excessive condition negatively affects on cool-season grass during the summer season, suggesting that excessive irrigation, over 70% field capacity of soil condition, does not help to reduce soil temperature for summer season in Korea. In the study that cool-season grass were treated with different water content of soil, The soil had higher temperature and more water holding capacity when treatment rate of soil conditioner was increased. The best growth at the normal water condition and the worst state of growth at thee water-excessive condition were observed.

• Korean Chemical Engineering Research
• /
• v.56 no.6
• /
• pp.871-877
• /
• 2018

Storing the surplus energy from renewable energy resource is one of the challenges related to intermittent and fluctuating nature of renewable energy electricity production. $CO_2$ methanation is well known reaction that as a renewable energy storage system. $CO_2$ methanation requires a catalyst to be active at relatively low temperatures ($250-500^{\circ}C$) and selectivity towards methane. In this study, the catalytic performance test was conducted using a pressurized bubbling fluidized bed reactor (Diameter: 0.025 m and Height: 0.35 m) with $Ni/{\gamma}-Al_2O_3$ (Ni70%, and ${\gamma}-Al_2O_3$30%) catalyst. The range of the reaction conditions were $H_2/CO_2$ mole ratio range of 4.0-6.0, temperature of $300-420^{\circ}C$, pressure of 1-9 bar, and gas velocity ($U_0/U_{mf}$) of 1-5. As the $H_2/CO_2$ mole ratio, temperature and pressure increased, $CO_2$ conversion increases at the experimental temperature range. However, $CO_2$ conversion decreases with increasing gas velocity due to poor mixing characteristics in the fluidized bed. The maximum $CO_2$ conversion of 99.6% was obtained with the operating condition as follows; $H_2/CO_2$ ratio of 5, temperature of $400^{\circ}C$, pressure of 9 bar, and $U_0/U_{mf}$ of 1.4-3.

• Science of Emotion and Sensibility
• /
• v.18 no.1
• /
• pp.49-58
• /
• 2015

This paper investigated far-infrared emission characteristics of ZrC imbedded heat storage knitted fabrics for emotional garment. For this purpose, ZrC imbedded heat storage PET was spun with high viscosity PET imbedded ZrC powder on the core part and low viscosity PET on the sheath part by conjugated spinning method. Ingredient analysis and far-infrared emission characteristics assessment of spun filament were carried out by EDS and FT-IR spectrometer. Two kinds of knitted fabrics were made using texturized ZrC imbedded PET for measuring thermal characteristics of ZrC imbedded heat storage PET. Zr peak was certified by EDS measurement and it was confirmed that content of Zr was 19.29%. Far-infrared analysis revealed that emission power at the range of wavelength, $5{\sim}20{\mu}m$ was $3.65{\times}10^2W/m^2$, and emissivity was 0.906. Heat storage analysis by KES-F7 system revealed that $Q_{max}$ of ZrC imbedded PET knitted fabric was lower than that of regular PET one and warmth keepability rate was higher than that of regular one, which means that ZrC imbedded PET knitted fabric has heat storage property. Thermal conductivity of ZrC imbedded PET knitted fabric was higher than that of regular PET one which was caused by high thermal conductivity of Zr itself. Hand property of ZrC imbedded knitted fabric was not inferior compared to regular PET knitted fabric, which preferably was found to be dependent on knit structure and surface property.

• 한국방재학회:학술대회논문집
• /
• 2011.02a
• /
• pp.194-194
• /
• 2011

현대 사회에서 차량을 비롯한 선박, 항공기와 같은 각종 수송수단들은 그 용도와 형태도 다양하고 널리 보급되어있을 뿐만 아니라 각 분야에서 없어서는 안 될 필수품이 되어 있다. 그러나 수송수단의 수와 활용빈도수가 증가함에 따라 그로 인한 차량화재, 선박화재 그리고 항공기화재 등과 같은 특수화재의 발생에 따른 재산 및 인명피해의 문제점들도 함께 늘어나고 있는 실정이다. 2009년 기준, 1년 동안의 전체 화재발생건수 47,071건 가운데 차량화재의 발생건수가 5,958건으로서 전체의 12.6% 정도를 차지하였다. 그뿐만 아니라 차량 내장재의 주 재질은 가연성을 지닌 열가소성 합성수지들로서 화재가 발생하였을 경우, 다량의 가연성 가스 및 독성가스를 방출하기 때문에 인명 및 재산 피해를 증가시키는 문제점을 갖고 있다. 하지만 아직까지도 이와 같은 수송수단에 대한 화재를 예방하거나 피해를 최소화할 수 있는 화재진압대책 등에 관한 연구는 미흡한 실정이다. 따라서 본 연구에서는 이러한 문제점을 해결하고 과학적이며 체계적인 대응방안을 수립하기 위한 기초 자료를 확보하고 이를 통한 수송수단의 화재안전성을 분석하고자 각종 수송수단에서 사용되는 오일을 대상으로 연소특성 분석 및 화재하중에 관한 연구를 수행하였다. 분석 대상 오일은 연료용과 부속용 오일로 크게 분류되며, 연료용 오일로는 차량용 경유와 휘발유 그리고 군용차량용 경유, 항공기용 백등유와 제트유, 선박용 고유황경유 등을 선정하였다. 부속용 오일로는 브레이크오일, 파워오일, 엔진오일, 자동변속기오일, 수동변속기오일을 대상으로 각각 일반용과 고급형 2가지씩 시료를 선정하여 분석을 수행하였다. 분석방법은 대상오일들의 기초물성을 고찰하기 위해서 비중계를 이용하여 각 시료들의 비중을 측정하였으며, 문헌으로부터 끓는점, 어는점 및 점도 등을 조사하였다. 또한, 대상오일들의 착화특성을 살펴보고자 콘칼로리미터와 인화점 측정기 및 발화점 측정기 등을 이용하여 발열량, 착화시간, 발연량, 발화점, 인화점 등을 측정하였다. 대상오일들의 물성 및 착화특성에 대한 측정결과를 살펴보면, 비중은 $725.8{\sim}1072.0kg/m^3$ 정도의 값을 나타냈고, 인화점은 영하의 인화점을 갖는 휘발유의 경우, 장비의 특성상 분석이 곤란하여 측정하지 못하였으며, 다른 시료들은 $45.3{\sim}266.6^{\circ}C$정도의 값을 나타냈다. 발화점은 $325.7{\sim}600.6^{\circ}C$정도의 값을 갖는 것으로 나타났다. 따라서 이와 같은 결과들을 활용하면 차량, 선박, 항공기 등에 대한 화재발생과 관련된 화재안전성을 분석하고 이를 통한 수송시스템의 화재에 대한 예방 및 대응 방안의 효율성을 높일 수 있을 것으로 생각된다.

• Korean Chemical Engineering Research
• /
• v.48 no.1
• /
• pp.68-74
• /
• 2010

In this study, fluidized-bed pyrolysis has been conducted in order to recover the bitumen contained in the oil sand. Canada Alberta oil sand contains 11.9% of bitumen and the bitumen-derived heavy oil produced in fluidizedbed tends to be upgraded relative to the bitumen. The continuous operation has been performed using $N_2$ as a fluidization gas at 1 atm and $500^{\circ}C$ in a reactor of 170 cm height. The results showed 87.76% of bitumen conversion, where liquid products are 74.45% and gas products are 13.31%. $H_2$, $O_2$, CO, $CO_2$, $CH_4$, and NO and $C_1{\sim}C_4$ hydrocarbons in the gas products were analyzed by on-line gas analyzer and gas chromatography, respectively. The pyrolysis oil was analyzed by using proximate analysis, heavy metal analysis, SIMDIS, asphaltenes, and heating value. By SIMDIS analysis, naphtha was 11.50%, middle distillation was 44.83% and heavy oil was 43.66%. It was obvious that the pyrolysis oil was upgraded compared with bitumens.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.5
• /
• pp.700-707
• /
• 2017

In the international natural gas market, natural gas has markedly low calories. The domestic calories standard of natural gas was changed and the performance and efficiency of many industrial machines using natural gas were affected because of low caloric natural gas. Therefore, in this study, a dual fuel engine fueled with natural gas and diesel was tested to examine the effects of the CNG substitution rate on the combustion characteristics, such as thermal efficiency, COVimep and heat release rate. The CNG substitution rate was defined as the ratio of CNG instead of diesel, which was calculated as the total energy. The conditions of the tested engine were fixed $1800rpm/500N{\cdot}m$. In addition, diesel fuel was injected at $16^{\circ}CA$ BTDC and the fuel pressure was fixed at 85 MPa; the lower heating value of CNG was $10,400kcal/Nm^3$. The results of the engine test showed that the amount of diesel fuel was changed according to the CNG substitution rate. Therefore, when the substitution rate was increased, the amount of diesel fuel was decreased, which affected the energy for ignition. In addition, the ignition delay duration was increased, which affected the thermal efficiency and torque. On the other hand, the COVimep was less than 5% and a stable combustion state of the engine was shown.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.3
• /
• pp.350-359
• /
• 2016

We performed fast pyrolysis of empty fruit bunch (EFB) in the range of temperature from $400{\sim}550^{\circ}C$ and 1.3 s of residence time. The effect of temperature on the yields and physicochemical properties of pyrolytic products were also studied. Elemental and component analysis of EFB showed that the large amount of potassium (ca. 8400 ppm) presents in the feedstock. Thermogravimetric analysis suggested that the potassium in the feedstock catalyzed degradation of cellulose. The yield of bio-oil increased with increasing temperature in the range of temperature from $400{\sim}500^{\circ}C$, while that of gas and biochar decreased and showed monotonous change each with increasing temperature. When the EFB was pyrolyzed at $550^{\circ}C$, the yield of bio-oil and char decreased while that of gas increased. Water content of the bio-oils obtained at different temperatures was 20~30% and their total acid number were less than 100 mg KOH/g oil. Viscosity of the bio-oils was 11 cSt (centistoke), and heating value varied from 15 to 17 MJ/kg. Using GC/MS analysis, 27 chemical compounds which were classified into two groups (cellulose-derived and lignin-derived) were identified. Remarkably the concentration of phenol was approximately 25% based on entire chemical compounds.