• Fire Science and Engineering
• /
• v.33 no.4
• /
• pp.83-88
• /
• 2019

This study examined the concentration of combustion gases while considering low ventilation and respiration frequency. A one-quarter-size ISO 9705 room corner test was performed. The concentrations of carbon monoxide and oxygen were measured in each case with the continuous inhalation of combustion gas with low ventilation (2, 6, and 10 LPM) and different respiration frequencies (2 s, 5 s, and infinity). The combustion of a gasoline pool fire in the compartment had a theoretical heat release rate of 5.34 kW. The results show that the deviation of the gas concentrations becomes higher as the low ventilation increases compared to the respiration frequency. In addition, as the respiration frequency increases, the variation in the minimum oxygen concentration is larger than the average value, while in the case of carbon monoxide, the variation in the average value is larger than the maximum value. These results show that the inhalation characteristics of refugees should be considered to investigate fires.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.7 no.1
• /
• pp.20-25
• /
• 2014

There are several severe problems for LED device, the next generation's economy green lighting: as the temperature increases, the lamp efficiency decreases; if the temperature is over $80^{\circ}C$, the lifetime of lighting decreases; Red Shift phenomenon that wavelength of spectrum line moves toward long wavelength occurs; and optical power decreases as $T_j$ increases. Thus, Heat sink design that can minimize the heat of LED device is currently in progress. While the thermal resistance of COB Type LED was reduced by direct coupling of LED chip to the board, residential 13.5W requires Heat sink in order resolve heat issue. This study designed Heat Sink suitable for residential 13.5W COB LED down-light and selected the optimum Fin thickness through flow simulation that packaged the designed Heat Sink and 13.5W COB. And finally it analyzed and evaluated the thermal modes using contacting thermometer.

• Clean Technology
• /
• v.20 no.1
• /
• pp.80-87
• /
• 2014

Numerical study was investigated to obtain the database for developing a fast pyrolysis power boiler by waste fuel. The studies with various conditions were performed using ANSYS FLUENT. Also, the fuel properties was experimentally analyzed to utilize the input parameters for numerical analysis, that were proximate and ultimate analysis, reaction kinetics included pyrolysis and combustion. The results showed that temperature, combustion and exhausted gases was changed with heating value of fuel and feeding rate. Finally, the stable operating condition by analyzing results was proposed.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.800-803
• /
• 2010

Tetrahydrotricyclopentadiene(below THTCPD) isomer is a good candidate for the high performance liquid fuel component because of high density and heat of combustion value. But it has bad fluidity. The object of this study was to find out the optimal reaction condition to improve the fluidity of THTCPD because initial reactant is solid state, So we have carried out isomerization reactions using aluminum chloride catalyst under varying the reaction condition such as reaction temperature and reaction solvents. The results showed that when using aluminum chloride catalyst, isomerization reaction was more active in dichloromethane(methylene chloride: MC), 1,2-dichloroethane(ethylene chloride: EC) and chloroform than n-hexnae and toluene and was effected by reaction temperature.

• Journal of the Korean Institute of Gas
• /
• v.12 no.3
• /
• pp.81-84
• /
• 2008

In this paper, the research was applied the mixture gas of Propane-DME (dimethyl ether) for being commercialization to residential gas ranges. In order to examine a correspondence between Korean Standard and thermal efficiency characteristics at each burner, experiments were performed with 100% Propane and the mixture gas of 80% Propane-20% DME. The experimental results were shown that the higher a mixture ratio of DME was used, the lower a thermal efficiency was gained. Those were due to low caloric value of DME. With 80% Propane-20% DME mixture gas, one of residential gas ranges was not satisfied the condition for the thermal efficiency value, 40%, Korean Standard. Consequently, the research needs about the standard for being commercialization to the mixture gas of Propane-DME.

• Resources Recycling
• /
• v.26 no.2
• /
• pp.25-32
• /
• 2017

Since the heating values of swine manures were very low at 859~1,075 kcal/kg, it was necessary to convert to carbonization residue by carbonization processes among thermal processes. The most important factor in the carbonization process of swine manure is the carbonization temperature, and it was evaluated the optimal range of carbonization temperature for swine manure in this study by the thermal characteristics and the reaction kinetics. The carbonization of swine manure could be described by the 1st order reaction and Arrhenius equation. The frequency factor (lnA) and the activation energy were estimated to be 3.05~13.08 and 6.94~18.05 kcal/mol, respectively. The range of optimal carbonization temperature range of swine manure was $260{\sim}300^{\circ}C$.

• Korean Chemical Engineering Research
• /
• v.57 no.2
• /
• pp.219-224
• /
• 2019

In this study, the adsorption characteristics of cephalomannine on commercial adsorbent Sylopute were investigated using different parameters such as adsorption temperature, time, and initial cephalomannine concentration for the efficient separation of Taxus chinensis-derived cephalomannine by adsorption process. The Temkin isotherm model showed good fit to the equilibrium adsorption data. The adsorption capacity decreased with increasing temperature and the adsorption of cephalomannine onto Sylopute was physical in nature. Adsorption kinetic data fitted well with pseudo-second-order kinetic mode. According to the intraparticle diffusion model, film diffusion and intraparticle diffusion did not play a key role in the entire adsorption process. The process of cephalomannine adsorption onto Sylopute was exothermic and spontaneous. In addition, the isosteric heat of adsorption was constant even with variation in surface loading indicating homogeneous surface coverage.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.5
• /
• pp.68-74
• /
• 2019

In this study, the mechanical property and durability of improved bond performance mortar shotcrete was investigated. Mortar shotcrete was prepared by replacing coarse aggregate with 100% fine aggregate in the shotcrete mixture proportion proposed in the road construction standard specification. OPC, GGBFS and anhydrite were used as binders, and polymer powder was substituted for 1% and 2% of binder for improving bond property. From the experimental results, it was found that the compressive strength decreased with increasing polymer addition, but the bond strength increased. The addition of polymer to mortar shotcrete also reduced the drying shrinkage and improved the resistance to carbonation. Initial hydration heat of mortar shotcrete decreased with the addition of polymer, and it was judged that the initial compressive strength decreased.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.4
• /
• pp.464-469
• /
• 2019

Tapered roller bearings are used widely in vans, trucks, and trains because they can support the vehicle in a stable manner even under a heavy load. The cage of a tapered roller bearing maintains the gap between the rollers, which prevents friction wear and suppresses heating. If the cage is severely deformed due to resonance, the roller may not be able to roll smoothly and even leave the cage. Consequently, it is very important to analyze the dynamic characteristics of the cage for reliable performance of a bearing. The cage essentially has geometrical tolerance in the manufacturing process. In this paper, the effects of those geometrical imperfections on the dynamic characteristics of the cage were investigated. As a result, natural frequency separation occurred near the natural frequency of the ideal cage due to geometrical imperfections. In addition, the interval was proportional to the magnitude of the geometric error, and the interval increased with increasing mode number.

• Journal of the Korean Institute of Gas
• /
• v.24 no.6
• /
• pp.55-60
• /
• 2020

As research and development of eco-friendly vehicles are expanding worldwide, additional devices of vehicles are reduced or deleted to increase the mileage, or research is being conducted to reduce weight. Among them, the multi-stage transmission that was applied to the internal combustion engine vehicle was deleted and replaced with a reducer, and the initial driving power is secured by increasing the torque through the control of the motor output value. However, since frequent motor speed change can result in a load increase, this study attempts to develop a compact and lightweight manual two-stage reducer with a general reducer structure. Therefore, a two-speed transmission with two gear ratio was designed by inserting a large gear and a small gear in a structure with a parallel shaft to connect the gears with a V-belt in the form of a parallel shaft reducer, and setting the gear ratio of the low and high gears respectively. In addition, power performance according to the rotational speed and load of the transmission was checked through a test, and the heat generation characteristics generated during driving were checked to verify the validity of the transmission.