• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.6
• /
• pp.95-103
• /
• 2013

Half Cell Potential (HPC) technique has been widely adopted for its quantitative evaluation of corrosion possibility. In this study, RC specimens with three different cover depths (10mm, 30mm, and 60mm) and w/c ratios (0.35, 0.55, and 0.70) are prepared and accelerated salt spray test (SST) is performed for 45 days. Steel corrosion occurs in the specimens with 0.55 of w/c and 10mm of cover depth. In the case of 0.70 of w/c and 30mm of cover depth, steel corrosion is also monitored. Considering the effect of cover depth and w/c ratio, HCP evaluation equation is proposed and the condition which can control steel corrosion is obtained. Furthermore, anti-corrosive conditions containing w/c ratio and cover depth are analyzed through Life 365 program and the conditions are compared with the results from this study.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.3
• /
• pp.19-26
• /
• 2017

Concrete is a construction material with porous media and corroded steel inside affects negatively to durability and structural safety. This study aims a derivation of quantitative relationship between measured HCP (Half Cell Potential) and corrosion amount considering cover depth and W/C (water to cement) ratio. For the work, cement mortar specimens with 3 different W/C ratios and 4 different cover depths are prepared, HCPs are measured with 3 different corrosion level. HCP measurement significantly increases in the saturated condition and linear relationship is observed between corrosion level and acceleration period. With increasing corrosion level and W/C ratio, and decreasing cover depth, HCP measurement increases. Considering total corrosion level and HCP measurements, relatively low COV(Coefficient of Variation) of 0.67 is evaluated through multi-linear regression analysis, however higher COVs over 0.90 can be obtained considering level of HCP measurement. In the room condition, corrosion level can be evaluated through measured HCP in the given conditions of cover depth, W/C ratio. diameter of steel inside.

• Journal of Conservation Science
• /
• v.34 no.6
• /
• pp.503-515
• /
• 2018

Stupa of State Preceptor Jigwang at Beopcheonsa temple site, Wonju, was conserved and restored in 1957. It was necessary to assess the degree of damage to the used mortar and to provide objective data on the necessity of its removal. Therefore, the HCP(half-cell potential) measurement used in concrete fields was applied. Multi-regression analysis of HCP data, following the rapid corrosion test of the roofstone mortar used by the rebar, resulted in a high correlation of HCP values(0.86), depending on the amount of corrosion and cover depth used for the steel bar. As a result, high correlation values(0.86) for the coefficients of determination were derived. The showed that the measurement of the wet conditions -431 to -663 mV on the roofstone indicated a corrosion damage rate of 90% or more after removal and restoration.

• Journal of Life Science
• /
• v.13 no.1
• /
• pp.42-46
• /
• 2003

Photoplethysmogram is widely used to measure heart rate and arterial blood oxygen saturation in human. This paper describes radial pulse waves recorded by photoplethysmogram with 940 nm wavelength infra red light. Radial pulse waves were varied according to the recording site. When recorded on the skin over radial artery, the radial pulse wave was inverted, comparing to the photoplethysmogram at fingertip. The mechanism of inverted pulse wave seemed to be caused by the change of the blood volume in the subcutaneous tissue between radial artery and the skin, which was reduced during systolic period and increased during diastolic period of the cardiac cycle. These results suggest that radial arterial wall may reflect infra red ray.

• Journal of the Korea Concrete Institute
• /
• v.25 no.6
• /
• pp.621-630
• /
• 2013

Several techniques for steel corrosion detection are proposed and HCP (half cell potential) technique is widely adopted for field investigation. If concrete has cracks on surface, steel corrosion is rapidly accelerated due to additional intrusion of chloride and carbon dioxide ions. This study is for an evaluation of HCP in cracked concrete exposed chloride attack. For this work, RC (reinforced concrete) beams are prepared considering 3 w/c ratios (0.35, 0.55, and 0.70) and several cover depths (10~60 mm) and various crack widths of 0.0~1.0 mm are induced. For 35 days, SST (salt spraying test) is performed for corrosion acceleration, and HCP and corrosion length of rebar are evaluated. With increasing crack width, w/c ratios, and decreasing cover depth, HCP measurements increase. HCP evaluation technique is proposed considering the effects of w/c ratios, crack width, and cover depth. Furthermore anti-corrosive cover depths are obtained through Life365 program and the results are compared with those from this study. The results shows relatively big difference in cracked concrete, however provide similar anti-corrosive conditions in sound concrete.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.284-284
• /
• 2012

본 연구에서는 다이오드 소자의 온도 증가에 따른 C-V 특성을 분석하였다. 180 kHz 주파수 조건에서 온도는 300 K에서 450 K까지 50 K 간격으로 가변하였다. 측정 결과 reverse bias 영역에서는 커패시턴스의 온도 의존성이 없었으나, forward bias 영역에서는 온도가 증가함에 따라 동일 전압에서의 커패시턴스가 증가하였다. 이로부터 온도가 증가 할수록 소자가 반전(inversion) 상태에서 축적(accumulation) 상태로 빨리 전환함을 확인하였으며, 1/C2-V 그래프로부터 온도 증가에 따른 전위장벽(Built-in potential, Vbi) 감소를 확인하였다. 전위장벽은 0.63 V에서 0.31 V로 온도 상승에 따라 약 0.1 V씩 감소하였다. 이는 energy band diagram에서 p-type 영역과 n-type 영역의 energy band 차가 감소해 공핍층 영역의 폭이 좁아짐을 의미한다. 공핍층의 두께 감소로 다이오드 전류의 급격한 증가뿐 아니라 위에서 언급한 바와 같은 C-V 특성을 보였다. 이번 연구에서는 기존의 보편화 된 I-V 측정을 통한 다이오드 소자 분석과는 달리 온도 변화에 따른 C-V 분석을 통해 소자 내부의 전위 장벽 및 공핍층 폭 감소에 따른 소자 특성 변화를 분석하였다.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.7
• /
• pp.26-36
• /
• 2002

Mach-Zehnder type traveling-wave optical modulators with 3-section and 5-section phase reversal were designed and fabricated on z-cut $LiNbO_3$ substrates. Optical waveguides were designed by means of the FDM(Finite Difference Method). Design of CPW traveling-wave electrodes were performed by the SOR(Successive Over Relaxation) in the active region and by the CMM(Conformal Mapping) in the input/output section. The optical response R(${\omega}$ calculated based on the measured S-parameters showed the bandwidth of 15GHz centered at 25GHz for the 3-section, and the bandwidth of 22GHz at 45GHz for the 5-section.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.12 no.3
• /
• pp.239-245
• /
• 2024

PS(Prestressed) tendons are under high tensile stress and have a smaller concrete cover than RC(Reinforced Concrete) member, so that the more conservative specifications on corrosion have been proposed for PS member. In this study, three levels of chloride concentrations(0.0 mol/l, 0.125 mol/l, and 0.25 mol/l) were prepared for evaluating the corrosion behavior in different position of 7 strand wires. For accelerating corrosion and measuring the corrosion amount in tendon, the tendon was embedded in partially saturated soil, and HCP(Half Cell Potential) was measured from the soil surface. During the test period of 28 weeks, HCP was measured every two weeks and the corrosion weight in the tendon was measured at 16 and 28 weeks of test period. Through the test, HCP result in tendon increased as the wires were located toward bottom due to high saturation. HCP in the lowest wire position showed an increase by 5.92 % compared to that in top position in 0.25 mol/l condition. The lower the position of the wire contained more saturation, which yielded increasing corrosion amount and HCP in tendon. In addition, the relation between corrosion weight and chloride concentration was quantitatively obtained through regression analysis.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2006.05a
• /
• pp.1338-1342
• /
• 2006

수자원의 계획과 관리를 위해 정확한 유량 측정은 무엇보다 중요하다. 이를 위해 다양한 유량 측정방법이 개발, 적용되고 있다. 본 연구는 국내 하천에 적용 가능한 다양한 유량 측정방법을 시험하천에 동시에 적용하여 유량 측정 방법간 비교를 목적으로 수행되었다. 비교를 위해 적용된 방법은 유속면적법, 부자법, ADCP법 등의 비연속적 방법과 기존 보를 이용한 방법, 초음파 유량계를 이용한 방법, 유속지수법, 실시간 경사면적법 등의 연속적 방법이다. 평저수기에 주로 적용될 수 있는 비연속적 방법인 유속면적법과 ADCP법의 비교에서는 유속면적법이 방류량 대비 평균 ${\pm}4.7%$의 오차를 가지며, ADCP법의 경우 ${\pm}4.6%$의 오차를 갖는 것으로 나타났다. 비연속적 방법과 연속적 방법을 동시에 비교하기 위해 평저수 5회, 홍수 2회를 포함하는 총 7회의 동시 유량측정이 수행되었다. 유속면적법과 ADCP법은 부적절하게 적용된 경우를 제외하면 오차는 대체로 10% 이내로 나타났다. 부자법의 경우 홍수시에만 적용되었으나 오차가 방류량 대비 20% 이상으로 다소 크게 나타났다. 연속적 방법은 기존 보의 경우 개발된 수 위-유량 관계의 이하의 저유량에 적용할 경우 오차가 다소 크게 산정되었으나 그 이외에는 대체로 10% 이내의 오차를 나타내었으며, 일부 저수위의 유속지수법을 제외하면 연속적 방법은 모두 오차가 10% 이내로 조사되었다. 향후 보다 장기간에 걸쳐 다양한 유량 범위에서의 검증이 필요하지만, 시험하천에서의 유량 측정 방법간 비교는 국내 하천에 적용할 수 있는 다양한 방법의 적용성을 평가하는데 기여할 수 있을 것으로 생각된다.향 범위는 최대 $0.07km^2$ 면적에 그 효과를 기대할 수 있을 것으로 판단되어, 남조 수화현상이 심화될 경우 인공순환에 의한 저감효과가 크지는 않을 것으로 예측된다. 조사 기간중 H호의 현존 식물플랑크톤량의 $60%{\sim}87%$가 수심 10m 이내에 분포하였고, 녹조강과 남조강이 우점하는 하절기에는 5m 이내에 주로 분포하였다. 취수탑 지점의 수심이 연중 $25{\sim}35m$를 유지하는 H호의 경우 간헐식 폭기장치를 가동하는 기간은 물론 그 외 기간에도 취수구의 심도를 표층 10m 이하로 유지 할 경우 전체 조류 유입량을 60% 이상 저감할 수 있을 것으로 조사되었다.심볼 및 색채 디자인 등의 작업이 수반되어야 하며, 이들을 고려한 인터넷용 GIS기본도를 신규 제작한다. 상습침수지구와 관련된 각종 GIS데이타와 각 기관이 보유하고 있는 공공정보 가운데 공간정보와 연계되어야 하는 자료를 인터넷 GIS를 이용하여 효율적으로 관리하기 위해서는 단계별 구축전략이 필요하다. 따라서 본 논문에서는 인터넷 GIS를 이용하여 상습침수구역관련 정보를 검색, 처리 및 분석할 수 있는 상습침수 구역 종합정보화 시스템을 구축토록 하였다.N, 항목에서 보 상류가 높게 나타났으나, 철거되지 않은 검전보나 안양대교보에 비해 그 차이가 크지 않은 것으로 나타났다.의 기상변화가 자발성 기흉 발생에 영향을 미친다고 추론할 수 있었다. 향후 본 연구에서 추론된 기상변화와 기흉 발생과의 인과관계를 확인하고 좀 더 구체화하기 위한 연구가 필요할 것이다.게 이루어질 수 있을 것으로 기대된다.는 초과수익률이 상승하지만, 이후로는 감소하므로, 반전거래전략

• The Journal of the Korea institute of electronic communication sciences
• /
• v.12 no.4
• /
• pp.539-544
• /
• 2017

In this paper, the broadband patch antenna for human counting systems is designed and fabricated using by the air dielectric substrate. Proposed antenna has a patch structure of the square structure with a 5 mm air layer and the vertical connection between the patch antenna and CPW feeding line is realized the stepped impedance structure. Optimized antenna through a 3D EM simulator is fabricated on a jig by manufacturing an antenna jig using a 3D printer with a size of 16.6 * 16.6 * 5 mm3. Proposed antenna is measured with the maximum gain of 5.71 dBi and the VSWR of below 2:1 at a frequency of 7.2 to 9.8 GHz. Also, a half power beam width characteristic of the antenna is measured $70^{\circ}$.