• Journal of the Korean Chemical Society
• /
• 제65권3호
• /
• pp.197-202
• /
• 2021

In this study, activated clay treated with H₂SO₄ (20% by weight) and heat at 90 ℃ for 8 h for acid white soil was used as an adsorbent for the removal of PO₄^3--P in water. Prior to the adsorption experiment, the characteristics of activated clay was examined by X-ray Fluorescence Spectrometry (XRF) and BET surface area analyser. The adsorption of PO₄^3--P on activated clay was steeply increased within 0.25 h and reached equilibrium at 4 h. At 5 mg/L of low PO₄^3--P concentration, roughly 98% of adsorption efficiency was accomplished by activated clay. The adsorption data of PO₄^3--P were introduced to the adsorption isotherm and kinetic models. It was seen that both Freundlich and Langmuir isotherms were applied well to describe the adsorption behavior of PO₄^3--P on activated clay. For adsorption PO₄^3--P on activated clay, the Freundlich and Langmuir isotherm coefficients, K_F and Q, were found to be 8.3 and 20.0 mg/g, respectively. The pseudo-second-order kinetics model was more suitable for adsorption of PO₄^3--P in water/activated clay system owing to the higher correlation coefficient R² and the more proximity value of the experimental value q_e,exp and the calculated value q_e,cal than the pseudo-first-order kinetics model. The results of study indicate that activated clay could be used as an efficient adsorbent for the removal of PO₄³-P from water.

• Journal of Korean Society of Transportation
• /
• 제29권5호
• /
• pp.121-138
• /
• 2011

More affordable and available cutting-edge technologies (e.g., wireless vehicle communication) are regarded as a possible alternative to the fixed infrastructure-based traffic information system requiring the expensive infrastructure investments and mostly implemented in the uninterrupted freeway network with limited spatial system expansion. This paper develops an advanced decentralized traveler information System (ATIS) using vehicle-to-vehicle (V2V) communication system whose performance (drivers' travel time savings) are enhanced by three complementary functions (autonomous automatic incident detection algorithm, reliable sample size function, and driver behavior model) and evaluates it in the typical $6{\times}6$ urban grid network with non-recurrent traffic state (traffic incident) with the varying key parameters (traffic flow, communication radio range, and penetration ratio), employing the off-the-shelf microscopic simulation model (VISSIM) under the ideal vehicle communication environment. Simulation outputs indicate that as the three key parameters are increased more participating vehicles are involved for traffic data propagation in the less communication groups at the faster data dissemination speed. Also, participating vehicles saved their travel time by dynamically updating the up-to-date traffic states and searching for the new route. Focusing on the travel time difference of (instant) re-routing vehicles, lower traffic flow cases saved more time than higher traffic flow ones. This is because a relatively small number of vehicles in 300vph case re-route during the most system-efficient time period (the early time of the traffic incident) but more vehicles in 514vph case re-route during less system-efficient time period, even after the incident is resolved. Also, normally re-routings on the network-entering links saved more travel time than any other places inside the network except the case where the direct effect of traffic incident triggers vehicle re-routings during the effective incident time period and the location and direction of the incident link determines the spatial distribution of re-routing vehicles.

• Journal of the Microelectronics and Packaging Society
• /
• 제19권1호
• /
• pp.61-66
• /
• 2012

Chemical Mechanical Planarization (CMP) is a polishing process used in the microelectronic fabrication industries to achieve a globally planar wafer surface for the manufacturing of integrated circuits. Pad conditioning plays an important role in the CMP process to maintain a material removal rate (MRR) and its uniformity. For metal CMP process, highly acidic slurry containing strong oxidizer is being used. It would affect the conditioner surface which normally made of metal such as Nickel and its alloy. If conditioner surface is corroded, diamonds on the conditioner surface would be fallen out from the surface. Because of this phenomenon, not only life time of conditioners is decreased, but also more scratches are generated. To protect the conditioners from corrosion, thin organic film deposition on the metal surface is suggested without requiring current conditioner manufacturing process. To prepare the anti-corrosion film on metal conditioner surface, vapor SAM (self-assembled monolayer) and FC (Fluorocarbon) -CVD (SRN-504, Sorona, Korea) films were prepared on both nickel and nickel alloy surfaces. Vapor SAM method was used for SAM deposition using both Dodecanethiol (DT) and Perfluoroctyltrichloro silane (FOTS). FC films were prepared in different thickness of 10 nm, 50 nm and 100 nm on conditioner surfaces. Electrochemical analysis such as potentiodynamic polarization and impedance, and contact angle measurements were carried out to evaluate the coating characteristics. Impedance data was analyzed by an electrical equivalent circuit model. The observed contact angle is higher than 90o after thin film deposition, which confirms that the coatings deposited on the surfaces are densely packed. The results of potentiodynamic polarization and the impedance show that modified surfaces have better performance than bare metal surfaces which could be applied to increase the life time and reliability of conditioner during W CMP.

• Economic and Environmental Geology
• /
• 제54권6호
• /
• pp.689-698
• /
• 2021

Since the mine reclamation scheme was implemented from 2007 in Korea, various remediation programs have been decontaminated the pollution associated with mining and 254 mines were managed to reclamation from 2011 to 2015. However, as the total amount of contaminated mine drainage has been increased due to the discovery of potential hazards and contaminated zone, more efficient and economical treatment technology is required. Therefore, in this study, the adsorption properties of arsenic was evaluated according to the adsorbents which were derived from water treatment sludge(Alum based adsorbent, ABA-500) and granular ferric hydroxide(GFH), already commercialized. The alum sludge and GFH adsorbents consisted of aluminum, silica materials and amorphous iron hydroxide, respectively. The point of zero charge of ABA-500 and GFH were 5.27 and 6.72, respectively. The result of the analysis of BET revealed that the specific surface area of GFH(257 m²·g^-1) was larger than ABA-500(126~136 m²·g^-1) and all the adsorbents were mesoporous materials inferred from N₂ adsorption-desorption isotherm. The adsorption capacity of adsorbents was compared with the batch experiments that were performed at different reaction times, pH, temperature and initial concentrations of arsenic. As a result of kinetic study, it was confirmed that arsenic was adsorbed rapidly in the order of GFH, ABA-500(granule) and ABA-500(3mm). The adsorption kinetics were fitted to the pseudo-second-order kinetic model for all three adsorbents. The amount of adsorbed arsenic was increased with low pH and high temperature regardless of adsorbents. When the adsorbents reacted at different initial concentrations of arsenic in an hour, ABA-500(granule) and GFH could remove the arsenic below the standard of drinking water if the concentration was below 0.2 mg·g^-1 and 1 mg·g^-1, respectively. The results suggested that the ABA-500(granule), a low-cost adsorbent, had the potential to field application at low contaminated mine drainage.

• Journal of the Korean Chemical Society
• /
• 제54권1호
• /
• pp.110-114
• /
• 2010

The equilibrium of adsorption of basics dyes RB 5 and BG 4 from a single dyes in the mixtures on the sodium-exchanged clay of the Maghnia (Algeria) was studied. The maximum adsorption capacities of BR5 and BG4 in single dyes were 465.13 and 469.90 mg/g respectively. In the simultaneous adsorption of BR5 and BG4 from mixture solutions, three different initials concentrations ratios R (R=$C_{(BR5)}/C_{(BG4)}$) were tested: 2.5/1, 1/1 and 1/2.5 using ADMI method. The isotherms adsorptions of dyes from the mixtures are characteristics of competition phenomenon. A very strong interaction between BR5 and BG4 for the active sites of adsorption of surface of clay is obtained for R = 1/1. The ratio R' (R'=$Qe_{(mixture)}/Qe_{(single)}$) of the adsorption capacity of BR5 and BG4 in the mixture were reduced by factor of 0.86, 0.74 and 0.84 for the initials concentrations ratios R (R=$C_{(BR5)}/C_{(BG4)}$) of 2.5/1, 1/1 and 1/2.5 respectively. The variation of the ratio of the adsorption capacity R‘ of BR5 and BG4 in the mixture solutions with initial concentration ratios R indicates that BR5 dye is slightly favourable in the competition adsorption than BG4. Langmuir and Freundlich models fit very well with adsorption behaviour of single dyes as well as the dyes in mixture solutions.

• Journal of Life Science
• /
• 제27권8호
• /
• pp.965-973
• /
• 2017

Conjugated linoleic acid (CLA) is a group of positional and geometric isomers of linoleic acid with conjugated double bonds at C9,C11 and C10,C12 positions. Of possible CLA isomers, a naturally occurring CLA isomer is c9,t11-CLA which is produced from linoleic acid by linoleate isomerase from various rumen and lactic bacteria, and mushroom mycelia. Meanwhile, synthetically prepared CLA contained an equal amount of c9,t11-CLA and t10,c12-CLA isomers, and other isomers as minor constituents. CLA was firstly mentioned in 1939 during the elaidinization reaction of linoleic acid. Thereafter, CLA was not an attractant to scientists because it was not scientifically interested any more. However, since the anticarcinogenic action was driven from 7,12-dimethylbenz[a]anthracene (DMBA)-induced mouse skin carcinogenesis in 1987, CLA-related researches were drastically elevated, resulting in approximately 6,100 research papers in literature, so far. CLA exhibited the significant biological activities: anticarcinogenic, antidiabetic, antihypertensive, antiatherosclerotic, body-fat reducing, antioxidative, antiinflammatory, testosterone producing and other activities. Interestingly, two major CLA isomers, c9,t11-CLA and t10,c12-CLA, exhibited different biological activities. Meanwhile, t,t-CLA isomers which is minor constituent of chemically synthesized CLA from linoleic acid exhibited more potent anticarcinogenic activity in carcinogen-induced animal models and cancer cell lines than other CLA isomrs. In the present review, the significant biological activities of CLA were discussed along with historical studies of CLA since 1939.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• 제8권2호
• /
• pp.296-305
• /
• 1998

A study was performed to evaluate an effect of toluene or ethanol pretreatment on the toluene metabolism. A slight liver damage in rats was induced by administration of 0.2 ml of toluene or 0.2 ml of 50% ethanol per 100 g of body weight intraperitoneally every other day for four weeks except the last day before sacrifice. One day before sacrifice, toluene was administered to rats pretreated ethanol or toluene and the control. Rats were sacrificed at the 1st, the 2nd, the 3rd and the 4th week after the first administration of xenobiotics mentioned above. Based on the histopathological findings, liver weight per body weight, serum alanine aminotransferase and hepatic glutathione content, toluene- or ethanol-pretreated groups showed the reversible liver injury. By the treatment of one dose of toluene, the contents of hippuric acid in urine was higher in the group pretreated with toluene or ethanol than control. The contents of cytochrome P-450, benzylalcohol dehydrogenase and benzaldehyde dehydrogenase activities were generally more increased in toluene- or ethanol-pretreated rats than control. $K_m$ values of the benzylalcohol dehydrogenase in pooled liver samples from toluene- and ethanol-pretreated groups were similar each other. $V_{max}$ values of toluene- or ethanol-pretreated group was higher than control. In conclusion, the toluene metabolism is accelerated in rats pretreated with toluene or ethanol.

• 한국해양학회지
• /
• 제25권1호
• /
• pp.8-20
• /
• 1990

A series of pore water data were obtained during the different time over one year period between October 1987 and October 1988, from a site on a muddy intertidal flat, located in the Kyeong-gi Bay, west coast of Korea, The results have revealed that the tidal flat is an environment of active nutrient the subface supplied by the overlying seawater is almost completely removed from the pore water at depth of about 10 cm below the sediment surface. The nutrients such as ammonium and phosphate are produced through this process and subsequently accumulated in the pore water forming steep gradients near the sediment surface. Below the main sulfate redirection zone, a secondary peak of dissolved sulfate was often observed. Greal seasonal variation of the pore water nutrient profiles was observed, which was particularly clear in their maximum concentration as well as in their concentration gradient. The rate constants of sulfate reduction and nutrient regeneration, estimated by using a diagenetic model (Berner, 1980), differ by an order of magnitude between the summer and winter seasons. The difference in sediment temperature may account for most of the calculated variation. The C:N:P ratio, calculated from the pore water nutrient gradients also exhibits a slight seasonal difference. The organic matter being decomposed by sulfate reduction appears to be depleted in depleted in nitrogen, compared to the average marine organic matter.

• Applied Chemistry for Engineering
• /
• 제31권4호
• /
• pp.377-382
• /
• 2020

A sequential design of experiments was employed to optimize MOF-235 synthesis for acetylene adsorption process. Two experimental designs were applied: a two-level factorial design for screening and a central composite design, one of response surface methodologies (RSM). In this study, 2³ factorial design of experiment was used to evaluate the effect of parameters of synthesis temperature and time, and also mixing speed on crystallinity of MOF-235. Experiments were conducted 16 times follwing MINITAB 19 design software for MOF-235 synthesis. Half-normal, pareto, residual, main and interaction effects were drawn based on the XRD results. The analysis of variance (ANOVA) of test results depicts that the synthesis temperature and time have significant effects on the crystallinity of MOF-235 (response variable). After screening, a central composite design was performed to optimize the acetylene adsorption capacity of MOF-235 based on synthesis conditions. From nine runs designed by MINITAB 19, the result was calculated using the second order model equation. It was estimated that the maximum adsorption capacity (18.7 mmol/g) was observed for MOF-235 synthesized at optimum conditions of 86.3 ℃ and 28.7 h.

• Applied Microscopy
• /
• 제39권3호
• /
• pp.253-260
• /
• 2009

GM-CSF is a multipotent growth factor, which also plays an important role during the process of wound healing. rrhGM-CSF was specifically produced from rice cell culture in our laboratory (Hanson Biotech Co., Ltd, Daejeon). The rrhGMCSF contains more oligosaccharide side chains than any other types of GM-CSF. This work was taken to evaluate the influence on wound healing of rrhGM-CSF in male golden hamsters. Full thickness skin defects of 9 mm in diameter were made in the back of hamsters, and 100 ${\mu}L$ ointment containing rrhGM-CSF 50 ${\mu}g/mL$ was applied. Control groups were given ointment without rrhGM-CSF. The wound sizes were relatively reduced and skin was well regenerated in the experimental group compared with the control group. Structurally, reepithelialization and architecture of the skin following injury were well accomplished in the experimental group. And also, positive reaction of PCNA of the skin following injury was more prominent in rrhGM-CSF containing ointment treatment group. Since this type of GM-CSF has highly glycosylated side chains, the effectiveness might be retain longer and stable, regarding acceleration of wound healing in the animal model. The present study has important implications for further development of the therapeutic manipulation of wound healing using rrhGM-CSF.