• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.3
• /
• pp.27-33
• /
• 1999

We have investigated the ultra-low energy B, P, and As ion implantation using upgraded MDRANGE code to study formation of nanometer junction depths. Even at the ultra-low energies simulated in this paper, it was revealed that ion channeling should be carefully considered. It was estimated that ion channelings have much effect on dopant profiles when B ion implant energies were more than 500 eV, P more than 2 keV and As approximately more than 4 keV. When we compared 2-dimensional dopant profiles of 1 keV B with that of tilted one, 2 keV P with tilt, and 5 keV As with tilt, we could find that most channeling cases occurred not lateral directions but depth directions.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.24 no.5
• /
• pp.494-498
• /
• 2004

Fire accidents often happen in large buildings because large buildings are equipped with heavy electrical wiring and piping. When fire is to be occurred in those buildings, it is very dangerous to People and building structures. Therefore, multi-point wireless temperature sensors for large buildings are necessary in order to detect fire in the early time and thus to minimize the loss. A wireless device was composed of the transmitter and receiver. The specification of this device was as follows: 915MHz of transmitted frequency, 4 channels, 9600bps of the transmitted speed, and 10mW of the transmitted power. We confirmed through experiment that the temperature was well sensed and fire location was determined by the 4 channel sensors of the developed sensor system.

• Journal of the Korean Ceramic Society
• /
• v.34 no.3
• /
• pp.314-322
• /
• 1997

The thin film processing and the applicability as a IMD material of SiO2 aerogels providing ultralow dielec-tric properties were studied. The SiO2 aerogel films with 0.5g/㎤ density (78% porosity) and 4000~21000$\AA$ thickness could be prepared at 25$0^{\circ}C$ and 1160 psig by supercritical drying of wet-gel films, which were spin-coated at the spin rate of 1000~7000 rpm on p-Si(111) wafer under the isopropanol atmosphere. The optimum viscosity of polymeric SiO2 sols for spin coating was in the range of 10~14 cP. The main fac-tors being able to control the film thickness and microstructures were found to be sol concentration, spin rpm, and aging time of wet-gel films. The dielectric constant of the SiO2 aerogel thin film was around 2.0 low enough to be applied to the next generation semiconductor device beyond the giga level.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.8
• /
• pp.285-291
• /
• 2013

In this paper, MOS-Capacitor and MOSFET devices with a Low Level Leakage Current of oxide thickness, channel width and length respectively were to investigate the reliability characterizations mechanism of ultra thin gate oxide films. These stress induced leakage current means leakage current caused by stress voltage. The low level leakage current in stress and transient current of thin silicon oxide films during and after low voltage has been studied from strss bias condition respectively. The stress channel currents through an oxide measured during application of constant gate voltage and the transient channel currents through the oxide measured after application of constant gate voltage. The study have been the determination of the physical processes taking place in the oxides during the low level leakage current in stress and transient current by stress bias and the use of the knowledge of the physical processes for driving operation reliability.

• Korean Journal of Materials Research
• /
• v.3 no.4
• /
• pp.319-326
• /
• 1993

The effects of $SnO_2$ crystallite size on the powder characteristics, the resistance in air and the sensitivity to 0.5 vol % $H_2$, CO-air mixture were observed. The size of SnO, powder was controlled by calcining temperature variation ($500^{\circ}C$ ~$1100^{\circ}C$) of $\alpha$-stannic acid fabricated from $SnCl_4 \cdot xH_2O$. Its crystallite size. evaluated from TEM image, was in the range of 8-54nm. With the reduction of crystallite size, the adsoption peak of $H_2O$ on FTIR curve became more clear while the lattice parameters were invariable. As the crystallite size decreased, with elements of thick film, the temperatures showing a minimum resistance in air and a maximum sensitivity to H, gas reduced. The temperature variations were assigned to the changes of activation energy of the active adsorbates, and it was suggested that the decrease of activation energy can be one of the reasons for the' sensitivity increase with the' fine powder.

• Korean Journal of Materials Research
• /
• v.22 no.9
• /
• pp.459-464
• /
• 2012

We investigated cleaning effects using $NH_4OH$ solution on the surface of Cu film. A 20 nm Cu film was deposited on Ti / p-Si (100) by sputter deposition and was exposed to air for growth of the native Cu oxide. In order to remove the Cu native oxide, an $NH_4OH$ cleaning process with and without TS-40A pre-treatment was carried out. After the $NH_4OH$ cleaning without TS-40A pretreatment, the sheet resistance Rs of the Cu film and the surface morphology changed slightly(${\Delta}Rs:{\sim}10m{\Omega}/sq.$). On the other hand, after $NH_4OH$ cleaning with TS-40A pretreatment, the Rs of the Cu film changed abruptly (${\Delta}Rs:till{\sim}700m{\Omega}/sq.$); in addition, cracks showed on the surface of the Cu film. According to XPS results, Si ingredient was detected on the surface of all Cu films pretreated with TS-40A. This Si ingredient(a kind of silicate) may result from the TS-40A solution, because sodium metasilicate is included in TS-40A as an alkaline degreasing agent. Finally, we found that the $NH_4OH$ cleaning process without pretreatment using an alkaline cleanser containing a silicate ingredient is more useful at removing Cu oxides on Cu film. In addition, we found that in the $NH_4OH$ cleaning process, an alkaline cleanser like Metex TS-40A, containing sodium metasilicate, can cause cracks on the surface of Cu film.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.10a
• /
• pp.42.1-42.1
• /
• 2011

박막형 디스플레이구서에 있어서 투명전극은 필수적이다. 투명전극은 정보를 표시하기 위해 빛을 외부로 방출시키거나 태양광 등을 소자 내부로 입사시켜야 한다. 또한 전극을 형성하는 박막은 높은 광투과율과 ${\sim}10-4{\Omega}cm$ 정도의 낮은 전기비저항을 가져야 한다. 가장 널리 사용되는 투명전극으로 ITO (Indium Tin Oxide)는 인듐의 독성, 저온증착의 어려움, 스퍼터링시 음이온 충격에 의한 막 손상으로 저항의 증가 및 액정디스플레이의 투명전극으로 사용될 경우 $400^{\circ}C$정도의 높은 온도와 수소플라즈마 분위기에서 장시간 노출시 열화로 인한 광학적 특성변화가 문제로 지적된다. 이러한 문제 해결의 대안으로 ZnO 산화물 반도체가 있는데 ITO 박막에 비해 비저항이 높기 때문에 도핑을 이용한 비저항을 ${\sim}10-4{\Omega}cm$ 정도로 낮추어야 한다. 투명전도막으로는 ITO, FTO 등과 더블어 체적 저항율은 다소 높으나 환원성 분위기에 대한 내성, 가시광 영역에서의 높은 광투과율과 저렴한 가격 등의 장점 등으로 AZO 박막이 주목 받고 있다. ZnO는 ITO 나 FTO에 비해서 700 kJ/mol의 큰 분해에너지를 가지므로 코팅 때 발생하는 전도도 및 투과율이 나빠지는 현상이 발생하지 않는 특징이 있으며, 위의 두 재료에 비해 밴드갭도 가장 낮아서 자외선 투과율이 낮다. 그러나 내습성이 약하기 때문에 이를 보완하기 위하여 내습성향상과 전도성 향상을 위해서 3족 원소인 B, In, Al, Ga 등을 도핑한 ZnO 투명전도막의 연구가 진행되고 있다. 이러한 원소들 중에서 Al로 도핑했을 때 가장 낮은 비저항을 얻을 수 있다고 알려져 있다. 본 연구에서는 SiOC 박막위에 AZO 박막을 제조하기 위하여 RF 마그네트론 스퍼터링법을 이용하여 박막을 성장시켰으며, 박막의 전기적 및 광학적 특성을 조사하였다. AZO 박막은 rf power가 5~200 W인 RF 마그네트론 스퍼터 방법에 의해서 제작되었다. SiOC 박막은 산소와 DMDMOS 전구체의 유량비를 다르게 하여 플라즈마 발생 화학적 기상 증착방법으로 증착되었다. 증착된 SiOC박막은 UV visible spectroscopy에 의해서 분석하였다. 투명전극의 비저항은 rf 전력이 작을 수록 낮았으며, SiOC 절연막 위에 AZO를 증착시킨 후 반사률은 반대로 바뀌는 것을 확인하였다.

• Korean Journal of Materials Research
• /
• v.20 no.4
• /
• pp.223-227
• /
• 2010

Recently, one-dimensional semiconducting nanomaterials have attracted considerable interest for their potential as building blocks for fabricating various nanodevices. Among these semiconducting nanomaterials,, $SnO_2$ nanostructures including nanowires, nanorods, nanobelts, and nanotubes were successfully synthesized and their electrochemical properties were evaluated. Although $SnO_2$ nanowires and nanobelts exhibit fascinating gas sensing characteristics, there are still significant difficulties in using them for device applications. The crucial problem is the alignment of the nanowires. Each nanowire should be attached on each die using arduous e-beam or photolithography, which is quite an undesirable process in terms of mass production in the current semiconductor industry. In this study, a simple process for making sensitive $SnO_2$ nanowire-based gas sensors by using a standard semiconducting fabrication process was studied. The nanowires were aligned in-situ during nanowire synthesis by thermal CVD process and a nanowire network structure between the electrodes was obtained. The $SnO_2$ nanowire network was floated upon the Si substrate by separating an Au catalyst between the electrodes. As the electric current is transported along the networks of the nanowires, not along the surface layer on the substrate, the gas sensitivities could be maximized in this networked and floated structure. By varying the nanowire density and the distance between the electrodes, several types of nanowire network were fabricated. The $NO_2$ gas sensitivity was 30~200 when the $NO_2$ concentration was 5~20ppm. The response time was ca. 30~110 sec.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.12
• /
• pp.4984-4990
• /
• 2010

In this paper, a Step-down CMOS DC-DC Converter using low power switched capacitor method is designed in a 0.5 ${\mu}m$ technology for the integration of devices. Conventional DC-DC converter is used inductor that can store energy in a magnetic field but have low efficiency because power consumption is caused by magnetic flux. And there were problems with size, weight and price to integrate chip. In this paper, a proposed Inductorless step-down CMOS DC-DC converter of low power using SC method is designed in a 0.5um technology to solve these problems. Designed DC-DC converter have 96% power efficiency with 200kHz frequency by using cadence simulation.

• Solar Energy
• /
• v.17 no.2
• /
• pp.55-66
• /
• 1997

The structural and optoelectronic properties of polycrystalline CdS films up to several microns in thickness, fabricated by three different methods, are compared to one another for the purpose of preparing CdTe/CdS solar cells. All films were deposited on an indium tin oxide on glass substrate. The three methods are: 1) alternated spraying of cation and anion solution at room temperature; 2) spray pyrolysis with substrate temperature up to $500^{\circ}C$; 3) chemical bath deposition (CBD). Deposited films were thermally treated in various ways. All films showed a well-developed wurtzite structure. Films grown by the alternated-spray method and the chemical bath method consist of randomly-oriented crystallites with dimensions <0.5 microns. Annealing at $400^{\circ}C$ increases the crystallite size slightly. Films which were grown by pyrolysis at substrate temperatures from $400^{\circ}C\;to\;500^{\cir\c}C$ were oriented in the <002> direction. For growth by pyrolysis at $500^{\circ}C$, the surface is rough on a lateral scale of 0.1 to 0.3 microns. The optical band gap and defect states are investigated by optical absorption, photoluminescene, Raman, and photothermal deflection spectroscopies.