• International Journal of Highway Engineering
• /
• v.12 no.3
• /
• pp.1-8
• /
• 2010

This study is performed to evaluate the physical and mechanical characteristics of an acryl polymer concrete that is developed as an overlay material for cement concrete slabs and pavements. Various laboratory tests including viscosity, flow, compressive strength, flexural strength, tensile strength, linear shrinkage, thermal expansion and thermal compatibility tests are performed. It is observed from the laboratory tests that the acryl polymer concrete developed in this study satisfies all the requirements suggested by ACI guideline. In addition to the laboratory tests, an accelerated performance testing (APT) is conducted to validate the performance of the acryl polymer concrete. During the APT, no significant distresses are observed until 15,903,939 cycles of equivalent single axle loading is applied. Finally, a 10mm thick overlay with the acryl polymer concrete is applied on top of an old deteriorated concrete pavement to evaluate field performance. Right after the field construction, skid resistance, noise and roughness are measured. The skid resistance and noise level have been significantly improved while the roughness is increased. Periodic investigation for the field study section will be conducted to evaluate the long-term performance.

• International Journal of Highway Engineering
• /
• v.12 no.1
• /
• pp.87-98
• /
• 2010

Surface of fine-size exposed aggregate Portland cement concrete pavements is consists of exposed coarse aggregate by removing upper 2~3mm mortar of concrete slab. Fine-size exposed aggregate PCC pavements have advantages of maintaining low-noise and adequate skid-resistance level during the performance period. In order to provide the successful exposed concrete aggregate pavement, uniform distribution of the coarse aggregate on pavement surface through adequate the mix design and exposing method. In this study, evaluated initial performance of fine-size exposed aggregate PCC pavement by experimental construction. And it was known that fine-size exposed aggregate concrete pavement which can reduce the noise and maintain the adequate level of skid resistance and strength.

• Proceedings of the Korean Society of Disaster Information Conference
• /
• 2017.11a
• /
• pp.127-128
• /
• 2017

최근에는 발생되고 있는 염화물계 제설제의 도로 손상, 차량 부식 및 미끄럼으로 인한 교통사고 문제를 해결하기 위해 친환경 제설제의 사용이 권장되고 있다. 그러나, 현재 수행되고 있는 친환경 제설제의 성능 시험 방법은 실내에서 얼음을 이용하여 실시되고 있으나, 실제 현장 성능과의 상관 관계가 낮은 것으로 나타났다. 따라서 본 논문에서는 현재 수행되고 있는 제설제 성능평가 방법을 소개하고 국내 실정에 부합하는 제설제의 성능 검증을 위한 현장 시험 방법을 제안하고자 한다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.11 no.5
• /
• pp.114-122
• /
• 2007

In high strength bolted joints, the corrosion of base material causes the reduction of slip resistance of the joints. In this study, tensile tests on slip-critical joints utilizing Zn/Al metal spraying corrosion resistance method were carried out in order to prevent the corrosion and meet the required mechanical characteristics of joints. In addition, slip coefficient and surface roughness were calculated. The key parameters were surface finishing condition and thickness of coating with the identical geometry in all specimens. From the results, it is found that the slip coefficient of the joints with coated finish after sand blast treatment as well as those of non-coated joints with only sand blast treatment were similar or superior to 0.45, which is a specification criteria of slip coefficient in friction-typed joints.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.6
• /
• pp.17-22
• /
• 2003

An airship is statically unstable, because it has no wing, relatively small tails and a large hull. Hence, an accurate prediction of dynamic stability is critical. In this study, dynamic stability data of the 50m Length Airship were acquired through forced oscillation wind tunnel tests. The tests were done in Birhle Applied Research Inc's Lange Amplitude Multi-Purpose(BAR LAMP) Facility located in Germany. The tests were composed with 16 static runs and 26 dynamic runs. As results, it is obtained that dynamic characteristics of the airship depend on the sideslip angle, the angular rate and its direction as well as the angle of attack. Generally, three directional moments have damping, but the normal force, the side force, and the cross-derivatives are unstable. The dynamic derivatives are not sensitive to the control surfaces, but nonlinear to the sideslip angle.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.2
• /
• pp.101-108
• /
• 2009

A fretting wear test rig for dry ambient condition, which employs a piezoelectric actuator, has been developed. It is driven and loaded in a very simple manner with acceptable experimental accuracy. By using the rig, Inconel 690 tube has been tested under the normal load of 10 and 15N with sliding amplitude of less than $100{\mu}m$ during $10^6$cycles. The wear resistance of the material has been characterized in terms of the wear coefficient based on the work rate model. SEM micrographs show the complex structures of the scars, which consist of risen peaks, plate-type thin layers and locally exposed bare surfaces. The cracks spread over the layers give clue to the fretting wear mechanism of the material.

• Proceedings of the KIEE Conference
• /
• 2002.07d
• /
• pp.2373-2375
• /
• 2002

전자 제어식 미끄럼 방지 제동 장치(ABS, Anti-lock Brake System)를 장착한 차량의 실차 제동 시험은 시험용 차량을 비롯하여, 많은 분석장비를 필요로 한다. 이러한 고가의 장비는 구하기가 어려울 뿐만 아니라 사용방법을 학습하는 데에도 상당한 기간을 필요로 하므로, 개발중인 ABS에 대하여 적용해 보기에는 그 사용에 제약을 받는다. 본 논문에서는 개발중인 미끄럼방지 제동 알고리즘과 전자제어장치(ECU, Electronic Control Unit)를 대형 버스에 장착하여, 저 점착 노면에서 주행 시험을 시행하였고, 그 주행 기록의 분석을 위하여 DAS(Data Acquisition System)를 구현하였다. 개발 ABS 알고리즘 및 ECU의 기능과 성능 검증이 목적인 DAS는 부가적인 센서 및 고가의 장비를 사용하지 않고 제어보드와 휴대용 노트북 컴퓨터를 이용하였다. 고정밀도의 자료를 획득할 수는 없었지만, 개발 DAS를 이용한 차량 실차 제동 시험은 경제적이면서도 효과적인 ECU 및 알고리즘의 성능 분석을 이룰 수 있었다. 특히 개발 DAS는 제어 및 Data Acquisition을 동일한 보드를 사용하여 구현함으로써, ABS 장착 실차 주행 시험 결과를 제어알고리즘에 즉각적으로 반영시킨 수 있었다. 이러한 One Board System 및 On-Vehicle Programming을 이용한 방법은 개발 알고리즘의 빠른 Debugging 및 파라미터 조정(Tuning)을 가능하게 하였으므로, 실차 제동 시험을 위한 한정된 기간 내에 개발 ABS ECU 및 제어 알고리즘의 성능을 효과적으로 검증할 수 있었다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.7
• /
• pp.531-538
• /
• 2017

A flush air data sensing system, which can predict flight speed, angle of attack, and angle of sideslip of the aircraft is designed and manufactured for a small UAV. Two kinds of flush pressure ports, four ports and five ports, are tapped at the same section of fuselage nose-cone. Calibration pressure data at flush ports are obtained through computations for the total aircraft by using Fluent code. Angle of attack, angle of sideslip, total pressure, and static pressure are represented with 4th-order polynomial function and calibration coefficient matrix is obtained using least square method with calibration pressure data. Flight test showed that flight speed, angle of attack, and sideslip angle predicted by four flush ports and five flush ports compared well with those by five-hole probe installed for data comparison. Especially four flush ports revealed nearly same results as those by five flush ports.

• Tribology and Lubricants
• /
• v.7 no.2
• /
• pp.28-35
• /
• 1991

3원통/링 마모시험기를 사용하여 윤활유 공급하에서 미끄럼 마모시험을 수행하였다. 엔진유에 첨가되는 대표적 첨가제인 ZDDP, 청정제, 분산제의 첨가제 3종과 모델 산호물로서 유성제인 스테아린산을 선택하여, 그 배합유의 마모방지특성을 조사하였다. 청정제 및 분산제 각각의 첨가에 의해 마모방지특성은 향상되었으나, 청정제 및 분산제를 동시에 첨가할 경우 마모방지성능의 향상효과는 없어졌다. 또한, 모델산화물인 스테아린산의 첨가로 인하여 ZDDP의 마모방지작용은 나빠지나, 청정분산제가 그 악영향을 억제하는 작용을 한다.

• Elastomers and Composites
• /
• v.36 no.2
• /
• pp.121-129
• /
• 2001

The friction characteristics of natural rubber plates under various conditions including sliding speed, normal force, hardness, lubrication conditions and thickness of plate are analyzed experimentally. The frictional force and normal force are measured by a tester pin and a load ceil with strain gages. Experimental results suggest that the coefficient of friction decreases with increasing the hardness of rubber and decreasing the thickness of plate. The effect of sliding speed is not significant over the speed range employed. The coefficient of friction is found to be about 0.1 under oil lubrication condition and varies from 0.9 to 3.9 under no lubrication condition.