• Journal of the Korean Geotechnical Society
• /
• v.15 no.5
• /
• pp.29-41
• /
• 1999

This Paper applied a simple strength parameter averaging method to double layered systems consisting of the strong sand layer overlying the soft clay deposit. This study derived a formula which defines a critical depth as the strength parameters, and used the correction parameter, $\alpha$ to reduce an error of the strength parameter averaging method. The results of the method were presented in the form of dimensionless charts and were compared with the results of several solutions proposed by Satyanarayana & Grag, Sreenivasulu, and Meyerhof & Hanna. The results of the proposed method coincided with the method of Meyerhof & Hanna and the results obtained from FLAC. But the Satyanarayana & Grag method and the Sreenivasulu method overestimated the bearing capacity. Consequently, the bearing capacity of foundation on sand layer overlying soft clay layer can be approximately estimated by using the proposed dimensionless charts.

• The Journal of the Acoustical Society of Korea
• /
• v.29 no.8
• /
• pp.491-496
• /
• 2010

Thermoacoustic power generation by a spiral heater in the Rijke tube was analyzed numerically. In the analysis, variables were normalized by the angular frequency of the sound and the thermal diffusivity of the air. The effect of the heater wire diameter d, the spacing between wires P-d, and the air-current velocity $U_0$, upon the power generation was obtained and discussed. When the spacing is broad enough, the normalized velocity is $U_0{\approx}0.8$ and the diameter is $d{\approx}4$ for the maximum power generation. With decrease of the spacing, however, the power generation increases more than 5 times and becomes maximum around $d{\approx}2$, $P-d{\approx}3$. And the velocity $U_0{\approx}0.8$ for the maximum power generation is almost independent of the wire spacing.

• Journal of Energy Engineering
• /
• v.11 no.1
• /
• pp.74-80
• /
• 2002

In this study, a numerical method for fuel droplet evaporation in cylinder of S.I. engine is presented. This study was newly defined non-dimensional critical droplet lifetime and modeled heating and evaporation processes of fuel droplet during intake and compression stroke of gasoline engine. The simulation results show that simultaneous increase of gas temperature and pressure in compression stroke seems to have compensative effect on droplet gasification rate. The environment variations in cylinder have little effect on the fuel droplet gasification process. The droplet size for full evaporation at the end of compression stroke can be estimated using this program.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.5
• /
• pp.833-839
• /
• 2003

The effects of stiffeners on the modal characteristics of rectangular plates are investigated. A modeling method for the modal analysis of rectangular plates with stiffeners is presented. A mass density Dirac's delta function is used to idealize the stiffeners mathematically. The equations of motion for the plates are derived and transformed into a dimensionless form. To confirm the accuracy of the method presented in this study, numerical result are obtained and compared to those of a commercial program. The mode shape variations due to some parameter variations are also exhibited.

• Journal of KSNVE
• /
• v.10 no.2
• /
• pp.312-318
• /
• 2000

A modeling method for the vibration analysis of rotating cantilever plastes with stiffeners is presented. The equations of motion for the plates aer derived and trnasformed into a dimensionless form. A mass density Dirac's delta function is used to idealize the stiffener mathematically. The effects of stiffeners on the model characteristics of the plate are investigated, and mode shape variations due to some parameter variation are exhibited. It is found that veering phenomena occur between some loci and associated mode shapes change significantly during the veering phenomena.

• Journal of KSNVE
• /
• v.8 no.6
• /
• pp.1130-1136
• /
• 1998

A modelling method for the vibration analysis of rotating cantilever plates with a concentrated mass is presented. The equations of motion for the rotating plates with a concentrated mass located in an arbitrary position are derived and transformed into a dimensionless form. For the mathematical modelling of the concentrated mass. a mass density Dirac delta function is used. The effects of concentrated mass and its location. angular speed. plate aspect ratio. and hub radius of the rotating plate on the natural frequencies are studied. Particularly. mode shape variations due to some parameter variations are investigated.

• The Korean Journal of Rheology
• /
• v.8 no.1
• /
• pp.39-48
• /
• 1996

최근에 본 연구자에 의하여 기존 스크류의 간단한 수정을 통해 단축 압출공정에서 의 혼합성능을 증진시키는 카오스 스크류를 개발하였고, 단축압출기에서의 기존스크류와 비 교하여 카오스 스크류를 사용하였을 경우 혼합성능이 월등하게 증진됨을 실험적으로 얻은 혼합형태로부터 알수 있었다. 본논문에서는 카오스 스크류에서 일어나는 카오스 유동을 집 중적으로 수치모사 하였으며 그결과를 중요한 무차원 변수에 대하여 입자 궤적,포인카레 단 면 본 논문에서 제안한 쉘사상법을 통하여 나타내었다. 쉘사사아법은 혼합형태와 불변체군 을 얻기에 매우 효과적인 방법이며 수치해석으로 얻은 불변체군은 실험결과와 잘 일치하였다.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.740-745
• /
• 2003

The so-called boundary node method (or NDIF method) that was developed by the authors has been extended for free vibration analysis of arbitrarily shaped plates with free edges. Since the proposed method is based on the collocation method, no integration procedure is needed on boundary edges of the plates and only a small amount of numerical calculation is required. A special coordinate transformation has been devised to consider the complicated free boundary conditions at boundary nodes. By the use of the special coordinate transformation, the radius of curvature involved in the free boundary conditions can be successfully dealt with. Finally, verification examples show that natural frequencies obtained by the present method agree well with those given by exact method and other analytical methods.

• Journal of Power System Engineering
• /
• v.14 no.4
• /
• pp.17-22
• /
• 2010

본 연구는 구의 과도 열전도에 의한 열손실을 계산하는 데 있어, 외부의 경계조건인 대류의 조건에 해당하는 상황을 상수 및 변수로 가정하였을 경우의 열전달문제를 해석한 것이다. 이 문제를 해결하기 위해 집중열용량법을 사용하고 있으며, 대류열전달계수의 값이 온도의 함수로 변한다고 가정하여 계산하였다. 계산을 수행한 결과 대류경계조건의 값을 상수로 가정한 경우가 열손실이 높이 평가된다는 것을 알았고, 이러한 경향을 상관식으로 정리하였다.

• Computational Structural Engineering
• /
• v.11 no.4
• /
• pp.275-286
• /
• 1998

본 논문은 고정, 단순, 또는 자유 연단 조건의 네 가지의 다른 조합을 갖는 마름모꼴형 평판의 자유진동 데이터를 처음으로 제시한 연구이다. 본 논문의 주된 관점은 마름모꼴 형 평판 둔각모서리의 휨응력의 특이도를 엄밀히 고려하여 해석하는 것이다. Ritz 방법을 이용하여 수직진동변위를 두 가지 적합 함수식으로 가정하였다. 힌지와 고정, 자유와 고정, 또한 힌지와 자유인 모서리 응력 특이도의 중대한 영향력이 이해될 수 있도록 충분히 큰 1650 둔각모서리를 갖는 마름모꼴형 평판에 대하여 엄밀한 무차원 진동수와 수직변동변위의 전형적인 등고선을 제시하였다.