• Journal of the Korean Institute of Gas
• /
• v.15 no.6
• /
• pp.1-7
• /
• 2011

The Measurement of risk parameter in city-gas equipments have been measured and confirmed by human, and evolved into remote monitoring system using wireless communication. Furthermore, domestic and international industry increase the efficiency of management, which can develop remote monitoring and control system using wireless communication. However, Those wireless system might be decrease the efficiency and ease because of connecting PDA and lap-top using wire-cable when data have checked immediately from outside. This paper is able to improve efficiency of safety management on city-gas equipments by developing mobile city-gas safety management system on AR.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.42 no.1
• /
• pp.233-240
• /
• 2017

Due to a recent rise in use of a wireless keyboard and mouse, attacks which take user's input information or control user's computer remotely exploiting the physical vulnerability in the wireless communication have been reported. Especially, MouseJack, announced by Bastille Network, attacks 2.4 GHz wireless keyboards and mice through exploiting vulnerability of each manufacturer's receiver. Unlike other attacks that have been revealed, this allows to attack AES wireless keyboards. Nonetheless, there is only a brief overview of the attack but no detailed information on this attacking method. Therefore, in this paper we will analyze the Microsoft 2.4 GHz wireless mouse packet and propose a way to set the packet configuration for HID packet injection simulating a wireless mouse. We also develop a system with 2.4 GHz AES wireless keyboard HID packet injection using the proposed packet and demonstrate via experiment that HID packet injection is possible through the system we built.

• Korean Journal of Remote Sensing
• /
• v.35 no.6_1
• /
• pp.987-997
• /
• 2019

Recently the demand for drones is rapidly increasing, as developing Unmanned Aerial Vehicle (UAV) and growing interest in them. Compared to traditional satellite and aerial imagery, it can be used for various researches (environment, geographic information, ocean observation, and remote sensing) because it can be managed with low operating costs and effective data acquisition. However, there is a disadvantage in that only a small area is acquired compared to the satellite and an aircraft, which is a traditional remote sensing method, depending on the battery capacity of the UAV, and the distance limit between Ground Control System (GCS) and UAV. If remote control at long range is possible, the possibility of using UAV in the field of remote sensing can be increased. Therefore, there is a need for a communication network system capable of controlling regardless of the distance between the UAV and the GCS. The distance between UAV and GCS can be transmitted and received using simple radio devices (RF 2.4 GHz, 915 MHz, 433 MHz), which is limited to around 2 km. If the UAV can be managed simultaneously by improving the operating environment of the UAV using a Long-Term Evolution (LTE) communication network, it can make greater effects by converging with the existing industries. In this study, we performed the maximum straight-line distance 6.1 km, the test area 2.2 ㎢, and the total flight distance 41.75 km based on GCS through LTE communication. In addition, we analyzed the possibility of disconnected communication through the base station of LTE communication.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.8 no.5
• /
• pp.73-80
• /
• 2008

The recent trend in home network system includes intelligent home environments that remote monitoring and control service is achieved without restrictions by device types, time, and place. Also the use of a vacuum robot in homes is gradually generalized on account of the convenience of the use. In this paper, we proposed and realized new home-monitoring system with the employment of an self-movement robot as one trial for realizing an intelligent home under home network environment. The proposed system can freely monitor every where in home, because the system effectively overcame the surveillance limitations of the existing monitoring system by attaching a Wireless Router and WebCam to a commercial vacuum robot. The outdoor users of this system can readily monitor any place which they want to supervise by controlling a vacuum robot with mobile telecommunication devices such as PDA. The wireless router installed with Linux operation system "OpenWrt" made it possible for the system users to transmit images and to control a vacuum robot with RS-232 communication.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.1
• /
• pp.202-208
• /
• 2015

A wireless ship area network is required to configure and control various sensors and electrical instruments embedded or boarded in a ship. In such environment, wireless communication protocol adopting relaying function is needed because direct link or communication between two nodes is hardly guaranteed due to spatial constraints in a ship. In this study, we introduce and analyze a WiMedia Distributed MAC (D-MAC) based approach considering throughput and energy constraint of wireless communication module. Performance evaluation results demonstrate that the relay-based wireless communication protocol improves reliability of wireless communication network in a ship.

• Journal of IKEEE
• /
• v.18 no.4
• /
• pp.552-558
• /
• 2014

This paper suggests how to design a ZigBee-chip-based communication module to remotely measure radiation level. The suggested communication module consists of two control processors for the chip as generally required to configure a ZigBee system, and one chip module to configure a ZigBee RF device. The ZigBee-chip-based communication module for remote radiation measurement consists of a wireless communication controller; sensor and high-voltage generator; charger and power supply circuit; wired communication part; and RF circuit and antenna. The wireless communication controller is to control wireless communication for ZigBee and to measure radiation level remotely. The sensor and high-voltage generator generates 500 V in two consecutive series to amplify and filter pulses of radiation detected by G-M Tube. The charger and power supply circuit part is to charge lithium-ion battery and supply power to one-chip processors. The wired communication part serves as a RS-485/422 interface to enable USB interface and wired remote communication for interfacing with PC and debugging. RF circuit and antenna applies an RLC passive component for chip antenna to configure BALUN and antenna impedance matching circuit, allowing wireless communication. After configuring the ZigBee-chip-based communication module, tests were conducted to measure radiation level remotely: data were successfully transmitted in 10-meter and 100-meter distances, measuring radiation level in a remote condition. The communication module allows an environment where radiation level can be remotely measured in an economically beneficial way as it not only consumes less electricity but also costs less. By securing linearity of a radiation measuring device and by minimizing the device itself, it is possible to set up an environment where radiation can be measured in a reliable manner, and radiation level is monitored real-time.

• Journal of Korea Multimedia Society
• /
• v.14 no.6
• /
• pp.794-801
• /
• 2011

Main machinery in the factory have various digital indicator to display its operating data for the manager. It is useful to control these datum at the remote office for factory automation in order to increase machine productivity. It is easy to use Ethernet infrastructure for remote communication. But most of all machinery in domestic factories still support RS232c or RS485 serial communication way. In this case to control machinery datum on the ethernet base, it is need to change RS232C or RS485 data to ethernet base. In this paper, in order to develop a remote progress management system through the wireless Internet, we show a design method to make easy maintenance by developing the system with both the JAVA language and RxTx Package for RS232c serial communication. For the system implementation, we added the digital indicator connect with a thermo couple to a machine which provide the real time status data of temperature. To connect machines management server program, we set up a convertor to change the RS485 data to the RS232c and also another convertor to change the RS232c data to wireless ethernet.

• Magazine of the Korean Society of Hazard Mitigation
• /
• v.11 no.1
• /
• pp.95-98
• /
• 2011

최근 국내에서 사회기반시설물에 대한 안전관리 네트워크 통합시스템 구축을 위한 국가핵심과제가 진행되고 있다. 본 연구에서는, 위 과제의 일환으로 진행 중인 철도교량의 구조건전성 모니터링 시스템 구축 및 운용에 대하여 기술하였다. 효율적인 철도교량 모니터링 시스템 구축을 위하여 다양한 종류의 스마트센서가 적용되었으며, 웹 기반의 네트워킹을 통해 외부에서 모니터링 시스템을 원격으로 접속, 제어 할 수 있도록 하였다. 철도교량의 국부 손상을 모니터링 하기 위해 압전센서를 활용한 무선 임피던스 노드를 적용하였고, 구조물 전체의 거동 분석을 위하여 가속도 센서 및 광섬유 센서를 적용하였다. 구조물의 장기 계측을 통한 철도 주행 및 외부 환경에 따른 거동 분석을 수행하였으며, 손상 평가를 위한 신호처리 알고리즘이 적용되었다.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.11 no.6
• /
• pp.207-214
• /
• 2011

In this paper, using Zigbee-based wireless sensor networks and Lego MindStorms NXT robot, a remote monitoring and navigation system for mobile robot has been developed. Mobile robot can estimate its position using encoder values of its motor, but due to the existing friction and shortage of motor power etc., error occurs. To fix this problem and obtain more accurate position of mobile robot, a ultrasound module on wireless sensor networks has been used in this paper. To overcome disadvantages of ultrasound which include straightforwardness and narrow detection coverage, we rotate moving node attached to mobile robot by $360^{\circ}$ to measure each distance from four fixed nodes. Then location of mobile robot is estimated by triangulation using measured distance values. In addition, images are sent via a network using a USB Web camera to smart phone. On smart phones we can see location of robot, and images around places where robot navigates. And remote monitoring and navigation is possible by just clicking points at the map on smart phones.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.1B
• /
• pp.9-18
• /
• 2006

Advances in wireless network are enabling the development of ubiquitous multimedia services. These multimedia services need efficient platforms to comply with the requirements of mobile computing. We introduce an adaptive service platform based on mobile agent and grid systems while specifying the challenges of ubiquitous multimedia services and focusing on frequent disconnections and scarce resources. We applied our platform to framework RtoA (Ready-to-Attend) which supports mobile users to access compute-intensive multimedia service, specifically, mobile education and video conferencing. RtoA includes hand-off, speaker and listener service which enable people to attend a conference or a class with satisfying quality of multimedia service. ns-2 based simulation verifies that our scheme is an efficient way to reduce energy consumption of mobile devices and to improve the response time of mobile applications.