• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.11
• /
• pp.529-535
• /
• 2018

The range extender vehicle runs on a mechanism that allows the small power generation engine to start in the most efficient specific operating range to charge the battery and extend the mileage. In this study, we developed a step motor type intake air supply system that replaces existing throttle body system to develop a simple low cost control logic system. The system was applied to the existing base engine, and in order to improve the performance by increasing the amount of intake air, the effect of changing the length of the intake and exhaust manifold was experimentally examined. As a result, the Type B intake air control actuator operated by one step motor showed higher performance than the Type A in all the operation region, but the performance was lower than that of the base engine due to the increase of flow resistance. To improve this, it was confirmed that the engine performance was improved at both speeds of 2200rpm and 4300rpm when the 140mm adapter was installed in the intake manifold and when the newly designed 70mm exhaust manifold was applied. Through this process, high - precision operation control was realized by connecting the generator load to the optimized engine for the range extender electric vehicle. Experimental results showed that the speed change rate was within ${\pm}2.5%$ at 2200rpm in 1st stage and 4300rpm in 2nd stage and the speed follow-up result of 610 rpm/s was obtained when the speed was increased from 2200rpm to 4300rpm.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.330-331
• /
• 2005

본 논문에서는 카메라폰용 광학중(Optical zooming) 과 자동초점조절장치 (Auto Focusing, AF)에 쓰일 초음파모터를 제작하였다. 초음파모터의제작 및 시뮬레이션은 유한요소해석 프로그램인 ATILA 5.2.1 (Magsoft co.)를 사용하여 디자인설계에 따른 구동특성을 고찰하였고 제작된 초음파모터는 한쪽 면이 없는 사작형의 탄성체를 제작하였으며 탄성체의 양쪽 다리에 각각 압전체를 부착하였다. 또한 압전세라믹의 조성은 $0.9Pb(Zr_{0.51}Ti_{0.49})O_3-0.1Pb(Mn_{1/3}Nb_{1/3}Sb_{1/3})O_3$의 조성으로 설계하였고 시편의 제조는 7-layer로 적층하였다. 제작된 압전세라믹의 치수는 6*2*0.35$mm^3$(길이*폭*두께)로 제작하였다 또한 탄성체의 외형치수는 10*10*2$mm^3$로 제작하였으며 두께를 각각 0.3[mm], 0.5[mm], 0.8[mm]으로 변화시키며 제작하였다. 두께가 0.8[mm]인경우 공진주파수는 60.5[kHz]를 나타내었으며 초음파모터의 압전세라믹에 인가전압이 증가함에 따라 회전속도와 모터에 흐르는 전류는 증가하였다. 인가전압이 40[Vpp] 일 때 회전속도는 206[rpm] 이며 소비전력은 0.3[W]로 제작된 시편은 카메라폰용 광학중 및 자동초점조절장치시스템 분야에 응용이 가능하다.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.24 no.5
• /
• pp.385-390
• /
• 2012

This paper discusses the applicability of a compact rolling piston refrigeration compressor to portable refrigerators. The capacity of this compressor is 1 cc. Using a 12 V BLDC motor, the compressor is driven from 2500 rpm to 6000 rpm. The height of the compression module and motor is approximately 56 mm, and their weight is approximately 374 g. We confirmed the effective operation of the compressor components by evaluating their compression and cooling performance.

• Korean Journal of Optics and Photonics
• /
• v.10 no.1
• /
• pp.5-9
• /
• 1999

We demonstrate a windmill type rotation of combined Mie particles caused by the evanescent field generated at the surface of a Gadolinium Gallium Garnet prism where a linearly polarized Nd:YAG laser beam (of wavelength 532 nm and power 100 mW) is totally reflected. The combined particles (e.g., doublets, triplets or quadruplets) consisting of polystyrene latex (or yeast) spheres with diameters of 3~5 m are reported to rotate at 0.1~1 rpm in water when the particles are slightly displaced from the center of the evanescent field.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.8
• /
• pp.408-415
• /
• 2006

This paper deal with control and design of 50,000rpm class Active Magnetic Bearing(AMB) system for high speed precision motor. In the design of AMB system, the design parameters adopted high robust rotor shaft, Active Magnetic Bearing, sensor and control system. In the design of Magnetic Bearing, 2-D Finite Element Method(FEM) is used and transfer matrix method is using for rotor dynamics. The control accuracy of high speed AMB system is demonstrated by experimentations.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2594-2599
• /
• 2008

This study deals with the development of PMSM(Permanent Magnet Synchronous Motor) for automotive EDC(Electric Drive Compressor). We have already developed the previous version of PMSM. It showed the characteristics of small size and high efficiency. But noise and vibration levels were higher than target values, so it was impossible to apply. So, in order to reduce noise and vibration levels, many parameters like the numbers of slots, the numbers of winding turns, and slot open width were changed. As a result, noise level of newly developed PMSM was decreased about 36.9% at maximum operating frequency (8600 rpm), and was reduced about 37.7% at rated frequency (6000 rpm) with the same sized and more efficient PMSM.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.79-82
• /
• 2004

In general, compressors for refrigerators are major noise source in home environment. The vibration originated from a pump of a compressor can make noise through suspension springs and a LDT(Line Discharge Tube). Especially for the inverter motor driven compressor, the vibration is more serious than it of the constant speed compressors. Because the operation frequency range of an inverter motor driven compressor is very wide from 1600 rpm to 4200 rpm. In this paper, we propose the numerical model to reduce vibration by designing weight balancers and grommets. Results for analytical investigations on the exciting force and moment at the pump mass center, weight balancers and exciting frequency variation are presented.

• Journal of the Korean Society of Mechanical Technology
• /
• v.13 no.4
• /
• pp.169-173
• /
• 2011

This study is about the development of remote controlled bollard using the BLDC motor and ball screw with mechatronics theory. A bollard is composed of the sensor part and the control part. The sensor part is consisted of sensors that detect the locations of a bollard. The role of the control part is adjusting motor speed and power through variable resistance. In order to confirm required performance, the speed of decent and ascent of the bollard, the time and the RPM of BLDC motor were tested according to the variable resistance and the applied load with 10 to $72kg_f$.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.10
• /
• pp.184-193
• /
• 2001

In vector control technique, stator currents of an induction motor are transformed to equivalent d-q currents in a reference frame consist of d and q axis, each of which is coincide with flux and torque direction respectively. Since the current in q-axis is related to the torque in a synchronously rotating frame, torque is estimated as a function of q-axis current and flux. In this paper, a method to estimate torque of an induction motor based on the measurement of 3-phase currents and rotating velocity of a rotor is presented. Graphic-programming is used to measure signals, to estimate the torque and to show the result in the form of user friendly graph in window environment. To stabilize the fluctuation of estimated torque caused from the small measurement error of the rotor velocity, the stator current is reconstructed in a program based on measured signals. The experimental results executed under the velocity of 500 rpm, 1500 rpm without load and 1500 rpm with load show that the proposed method estimates the torque very well.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.1 s.173
• /
• pp.269-274
• /
• 2000

Frictions and electrical contact voltages of the herringbone-grooved hydrodynamic bearing(HHB) were 9, measured to use in a laser scanner motor. This bearing with varying loads, speeds, oil viscosity, and radial clearances successfully operated up to 28,000rpm and 0.5N. Experimental results under various environments confirmed that this bearing had excellent performance with low friction force, and operated without contact between shaft and sleeve.