• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.4
• /
• pp.188-194
• /
• 2013

Hydrostatic pumps and motors occupy an important position in hydraulic system. There are a lot of researches on characteristics of hydraulic pumps, but not hydraulic motors. So in order to know the characteristics of hydraulic motors we had this research. The purpose of this study is to derive and analyze the theoretical calculation of hydraulic axial piston motor torque and torque ripples. Then, analyzed the differences between torque ripples with dead place and without dead place on the valve plate, and modeling a hydraulic motor with AMESim software. Finally, theoretical calculation of hydraulic motor torque ripples was verified from the viewpoint of simulation.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.254-259
• /
• 2005

The heat and vibration effect is known to cause a serious deformation in linear motor system. The paper presents a heat and vibration characteristics that compare a advanced linear motor with developed linear motor through experiment and analyses. The heat in linear motor system is identified for experimental data and analytic data using the Finite Volume Method (FVM). Also, it shows that the optimum standard analyzed the acceleration patterns of the moving part cause the vibration source in linear motor. It presents the analyzed dynamics of linear motor in compliance with a deformation of the non-linear factor.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.10a
• /
• pp.8-13
• /
• 2001

In the turning process, the feed is usually selected by a machining operator considering workpiece, cutting tool and depth of cut. Even if this selection can avoid power saturation or tool breakage, it is usually conservative compared to the capacity of the machine tools and can reduce the productivity significantly. This paper proposes a selection method of the feed and the reference cutting force based on MRR(material removal rate), maximum spindle power and specific energy. In order to estimate and control cutting force accurately in transient and steady state, this study utilizes a synthesized cutting force estimation method and a Fuzzy controller. The experimental results present that these systems can be useful for the FMS(flexible manufacturing system) and unmanned automation system.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.2 no.1
• /
• pp.150-158
• /
• 1999

A driving system of a dynamic FOG compass with a stabilized platform is described. A stepping motor adopted as a driving motor is required to maintain a stable operation with constant speed and low oscillation for the proper operation of the FOG compass itself. The previous stabilization scheme operated on frequency-modulated supply is modified to include fuzzy control algorithm. The proposed scheme has advantages, particularly in the size, weight and flexibility of the driving system.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.213-216
• /
• 2008

U. S. and NATO allies have recently increased their emphasis on reducing the hazards of tactical munitions that contain energetic materials and actively started many investigations on Insensitive munitions(IM) of missile propulsion. All subcomponents of rocket motor should be properly designed and understood to increase IM properties. Insensitive propellant, motor case, ignitor and mitigation devices are important components of IM technologies of rocket motors.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.647-650
• /
• 2001

In case of bent axis type axial piston hydraulic pump or motor, hydrostatic bearing used to achieve the lubrication effect on the mechanical sliding contact areas between the following pairs ; piston shoe and swash plate, valve plate and cylinder block, piston and cylinder block, etc. In this research, we designed two pairs of spherical ball joint in witch connecting rod piston end. The one is not hydrostatic bearing, the other is designed with spherical hydrostatic bearing in point of view minimum pumping power loss. By varying supply pressure on the piston, we can know that it is possible to reduce the friction torque by using hydrostatic bearing designed one. Finally, by comparing the results of driving torque between the two models, it was verified that the spherical hydrostatic bearing is well designed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.196-201
• /
• 2008

This paper is about electromagnetic vibration source in outer rotor type of BLDC motors. Experiments are carried out with three pole-slot combinations which are 6 slots, 12 slots, and 24 slots with 4 poles rotor. According to results, vibration sources separate into electromagnetic and mechanical factors. Using the finite element method (FEM), It is analyed that vibration characteristics of electromagnetic source in each type. This paper shows electromagnetic sensitivity to vibration, and introduces necessary point in lower vibration motors. Also rotor balance is important to prevent uneven distribution of magnetic flux between rotor and stator.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.2
• /
• pp.110-115
• /
• 2000

This paper describes the driving principles genometrically and analyzed the generating torque with the structure of magnetostatic wobble motor and electrostatic wobble motor. Then we compare the torque characteristics of magnetostatic wobble motor with those of electrostatic wobble using. F.E.M. Through the results, we investigate how the changes of design affect torque characteristics.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.7
• /
• pp.1446-1452
• /
• 2002

In the turning process, the feed is usually selected by a machining operator considering workpiece, cutting tool and depth of cut. Even if this selection can avoid power saturation or tool breakage, it is usually conservative compared to the capacity of the machine tools and can reduce the productivity significantly. This paper proposes a selection method of the feed and the reference cutting force based on MRR(material removal rate), maximum spindle power and specific energy. In order to estimate and control cutting force accurately in transient and steady state, this study utilizes a synthesized cutting force estimation method and a Fuzzy controller. The experimental results show that these systems can be useful for the unmanned turning process.

• Journal of computational fluids engineering
• /
• v.15 no.4
• /
• pp.109-114
• /
• 2010

In a fan design, CFD analysis, which is very useful for mechanical design relating to the heat and fluid dynamics, is one of the most popular tools. However, since the CFD analysis is conventionally carried out with the constant fan speed condition, the speed change, induced by the air flow rate and motor characteristics, is hardly modeled. And, consequently, the remarkable difference exist between analysis and experimental results. In this paper, we has proposed a method of setting the varying fan speed as a boundary condition considering air flow rate and motor torque-speed characteristics. The effectiveness of the proposed method is verified by comparison with experimental results.