• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.35 no.2
• /
• pp.29-36
• /
• 2019

Modular construction has benefits such as short construction duration and high productivity owing to the production in factory and owing to simultaneous on-site work. However, rework occurs in modular construction and the rework affects the efficiency of modular construction. The almost of causes of rework are exist in design process. To reduce the cause of rework, the information flow of the design process should be managed and the plan to reduce rework should be included. However, the modular construction has complex process because of impeded unit production so it is hard to manage the information flow in design process. Moreover, when the plan to reduce rework is included, the design process will be more complicated. Therefore, the objective of this research is to suggest the design process including the rework reduction plan and to alleviate the complexity of design process by using Dependency Structure Matrix(DSM). By using DSM, the iteration and feedback in design process is reduced and it can be expected that rework in modular project can be reduced by using suggested design process.

• Journal of the Korea Society of Computer and Information
• /
• v.25 no.1
• /
• pp.13-19
• /
• 2020

In this paper, we propose a multiplexer based scheme that performs modular AB² multiplication using redundant basis over finite field. Then we propose an efficient multiplexer based semi-systolic AB² multiplier using proposed scheme. We derive a method that allows the multiplexers to perform the operations in the cell of the modular AB² multiplier. The cell of the multiplier is implemented using multiplexers to reduce cell latency. As compared to the existing related structures, the proposed AB² multiplier saves about 80.9%, 61.8%, 61.8%, and 9.5% AT complexity of the multipliers of Liu et al., Lee et al., Ting et al., and Kim-Kim, respectively. Therefore, the proposed multiplier is well suited for VLSI implementation and can be easily applied to various applications.

• The KIPS Transactions:PartC
• /
• v.8C no.1
• /
• pp.32-40
• /
• 2001

In this paper, we propose a high-speed modular multiplication algorithm which revises conventional Montgomery's algorithm. A hardware architecture is also presented to implement 1024-bit RSA cryptosystem for digital signature based on the proposed algorithm. Each iteration in our approach requires only one addition operation for two n-bit integers, while that in Montgomery's requires two addition operations for three n-bit integers. The system which is modelled in VHDL(VHSIC Hardware Description Language) is simulated in functionally through the use of $Synopsys^{TM}$ tools on a Axil-320 workstation, where Altera 10K libraries are used for logic synthesis. For FPGA implementation, timing simulation is also performed through the use of Altera MAX + PLUS II. Experimental results show that the proposed RSA cryptosystem has distinctive features that not only computation speed is faster but also hardware area is drastically reduced compared to conventional approach.

• Elastomers and Composites
• /
• v.39 no.2
• /
• pp.95-104
• /
• 2004

New compounds were made using various NR/BR blend ratio and oil content to improve mechanical properties of rubber isolator at low temperature. Mechanical properties were investigated as a function of NR/BR blend ratio and oil content. Hardness and tensile modulus generally increased, but tensile strength and elongation at break decreased with increasing BR content. Hardness, tensile modulus and tensile strength decreased, but elongation at break were nearly the same with increasing oil content. The glass transition temperature of NR and BR were found to be $-50^{\circ}C$ and $-90^{\circ}C$ respectively based on the abrupt drops in storage elastic modulus and peak of loss factor. Two distinct transition temperature were observed in NR/BR blend compounds and each transition point was not affected by blend level indicating incompatible nature of NR/BR blend.

• The KIPS Transactions:PartC
• /
• v.17C no.2
• /
• pp.145-152
• /
• 2010

In this paper, we first propose a fast division algorithm in GF($2^{163}$) using standard basis representation, and then it is mapped into divider for GF($2^{163}$) with iterative hardware structure. The proposed algorithm is based on the binary ExtendedGCD algorithm, and the arithmetic operations for modular reduction are performed within only one "while-statement" unlike conventional approach which uses two "while-statement". In this paper, we use reduction polynomial $f(x)=x^{163}+x^7+x^6+x^3+1$ that is recommended in SEC2(Standards for Efficient Cryptography) using standard basis representation, where degree m = 163. We also have implemented the proposed iterative architecture in FPGA using Verilog HDL, and it operates at a clock frequency of 85 MHz on Xilinx-VirtexII XC2V8000 FPGA device. From implementation results, we will show that computation speed of the proposed scheme is significantly improved than the existing two approaches.

• Elastomers and Composites
• /
• v.35 no.3
• /
• pp.173-179
• /
• 2000

Cure characteristics. tensile properties, and dynamic properties were investigated on the carbon black-filled natural rubber compounds, in which three typical vulcanization types conventional vulcanization(Conv), semi-efficient(Semi-EV), and efficient(EV) vulcanizations were used. The effects of vulcanization temperature on both the mechanical property and aging resistance of rubber compounds were also investigated. The Conv cure system showed a slightly slower rate of vulcanization than those of Semi-EV and EV ones. On the other hand, it showed a higher value in the maximum torque of cure curve. Higher tensile moduli were observed in Conv system than those in Semi-EV and EV ones, while lower elongation at break were obtained in Conv one. The tensile strength at break were found to be about the same for three cute systems. Hardness, modulus, and tensile strength decreased with increasing the vulcanization temperature, and the degree of changes in the properties was found to be smaller for EV and Semi-EV systems than that in Conv one. The EV system was found to be superior in thermal-aging resistance to Conv one.

• Elastomers and Composites
• /
• v.36 no.2
• /
• pp.111-120
• /
• 2001

Mechanical properties and their adhesion behavior with zinc- and brass-plated steel cords of natural rubber/acrylonitrile-butadiene blend compounds were investigated as a function of blend ratio. The Mooney viscosity and stress relaxation time were found to be lowered with increasing NBR content. Tensile modulus generally increased with increasing NBR content. Tensile stress at break stayed constant up to about 40 phr and showed minimum at $50{\sim}60 phr$, and thereafter increased with increasing NBR content. Strain at break decreased linearly below 50 phr, and above the level it showed nearly constant value. Based on the abrupt drops in elastic modulus and tan ${\delta}$ peak, the glass transition temperature of NR and NBR were found to be -55 and $-10^{\circ}C$, respectively. In the case of NR/NBR blend compounds, two distinct transition points were observed and each transition position was not affected by NBR level indicating an incompatible nature of NR/NBR blend system. The pullout force and rubber coverage decreased to the level of about 40% to that of pure m compound, when the 50 phr of NR was replaced by NBR. However, the pure NBR compound showed the comparable adhesion performance with NR(${\sim}90%$). The sulfur concentration was found to become lower with the increased NBR content at the adhesion interface based on the Auger spectrometer results, representing a lack of adhesion layer formation, and this was explained for a possible cause of low adhesion performance with adding NBR.

• Resources Recycling
• /
• v.31 no.3
• /
• pp.53-60
• /
• 2022

The physical properties of chlorine-containing cement were analyzed to optimize the operational conditions when waste resources containing chlorine were used in the cement manufacturing process. Cement with clinker to gypsum weight ratios of 95:5 and 93:7 were manufactured. In addition, the iron modulus (IM) of clinker was set to 1.3, 1.5, and 1.7 to evaluate the burnability and physical properties of clinker. With constant chlorine content, increasing gypsum content resulted in a decrease in the 3 day-compressive strength, whereas the 28 day-compressive strength increased. In addition, flow and setting time also increased with increasing gypsum content. As the IM decreased, burnability was improved, free-CaO content decreased, alite and ferrite content increased, and compressive strength increased In particular, the compressive strength of IM 1.3 was approximately 14% greater than that of IM 1.7.

• Journal of the Korean Institute of Gas
• /
• v.16 no.6
• /
• pp.123-127
• /
• 2012

In order to establish the cause of the deformation of polyurethane foam, compression set was measured according to the aging temperature and time. FT-IR, TGA, DSC and DMA were used for investigating the cause of deformation of aged PUF. The results of FT-IR and TGA reveals that no structure change occurred during deformation of PUF. Resilience of aged PUF was reduced by the increase of reduction ratio in storage modulus over the glass transition temperature of hard segment.

• Elastomers and Composites
• /
• v.35 no.4
• /
• pp.261-271
• /
• 2000

Physical properties of NR vulcanizates cured by both sulfur and resole were studied. Cure characteristics of the compounds were also investigated. Two types of resoles with different molecular weight distributions were employed. The scorch time of the NR compound containing the resole with a low molecular weight distribution was shorter than that of the compound containing the resole with a high one. Crosslink densities of the NR vulcanizates with a high resole content after the thermal aging at $95^{\circ}C$ decreased, while that of the vulcanizate without resole after the thermal aging at $95^{\circ}C$ increased. Though crosslink densities of the NR vulcanizates with a high resole content decreased with increasing the aging time, the moduli increased while the tensile strength and tear strength decreased.