• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.10a
• /
• pp.493-497
• /
• 2002

In the part industry, pipe has required high accuracy in surface roughness and size. Especially, when producing the high frequency welding pipe, cutting process is very important as the finishing process that remove the hot welding bead. The objective of this paper is to investigate the hot machining high frequency welded pipe by simulation and experimental tests. To test the cutting process as hot machining, all cutting environment is reproduced in turning with heating system, and the test is accomplished by comparing with room temperature machining and hot machining in consideration of cutting force, tool wear and cutting temperature.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.05a
• /
• pp.240-244
• /
• 1999

This paper deals with the establishment of the cutting direction on inclined plane by using ball end mill. Ball-end milling is widely used for free form surface die and mold. In these machining, the cutting parts vary because the tool tip is hemisphere shaped. The cutting characteristics, such as cutting force, surface roughness and surface profile are varied according to the variation of cutting directions. The effective tool diameter was calculated on different tilt angles and tool-path. Tool life and cutting characteristics were estimated on variation of cutting directions in the same cutting speed. In this paper, the optimal cutting direction which can be applied 3-D sculpture surface cutting is suggested.

• Management & Information Systems Review
• /
• v.22
• /
• pp.167-191
• /
• 2007

The EU has introduced various environmental protection policies and regulations which are stricter than accepted international standards. WEEE, RoHS, and EuP directives in the Electrical and Electronic Industry could have a direct effect on our exports to EU countries. To gradually enlarge exports to the EU, it is necessary to have a precise understanding of the EU's environmental regulations and prepare the relevant countermeasures to adequately cope with them. Korean companies should formulate concrete plans to meet the EU's environmental regulations in those industry. In order to decrease the negative effects that environmental regulations of EU give to Korea, the corporations and the government should change their present passive environmental policy and carry out the environmental- friendly policy. If Korean companies can adequately meet the standards set by the environmental policies and regulations of the EU, it will greatly enhance the competitiveness of companies in this market.

• Journal of Chest Surgery
• /
• v.27 no.2
• /
• pp.136-139
• /
• 1994

Tracheal stenosis is relatively common complication after tracheal intubation or tracheostomy for a long time. We experienced 10 cases of tracheal stenosis with various causes, prolonged intubation or tracheostomy caused the tracheal stenosis in seven, one after advanced cancer of the lung, one after inhalation burn, and the other was palliative management for tracheal stenosis by Gianturco type tracheal stent. We tried to correct this stenosis applying three tracheal stent and one Montgomery T-tube as a palliative approach, but failed in two, one restenosis due to regrowing of granulation tissue with scarring or another metastatic spread of cancer to systemic organs after 3 months of placing the stent. Tracheal circumferential resection and end to end anastomosis were done in seven, and obtained one postoperative complication as subglottic stenosis was followed by Montgomery T-tube and reoperation later. With the brief review of references, we report the cases.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.11
• /
• pp.125-129
• /
• 2004

For the diagnosis of compressor abnormal condition in air-conditioner, AE signal which is derived from wear condition, compressed air and assembly error is analyzed experimentally. The burst and continuous type AE signal occurred by metal contact and compressed air and AE raw signal of compressors were directly acquired in production line. After extracting samples according to waveforms, Early Life Test(ELT) is conducted and classified to normal and abnormal waveform. The efficient parameters of waveform pattern are investigated in time and frequency domain and the diagnosis algorithm of air-conditioner by Neural Network estimation is suggested.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.11
• /
• pp.189-198
• /
• 1998

Recently, monitoring of tool life is a matter of common interesting because tool life affects precision, productivity and cost in machining process. Especially flank wear has a direct effect on cutting mechanism, so the various pattern of cutting force is obtained experimentally according to variation of wear condition. By investigating cutting force signal, AR(Autoregressive) modeling and correlation dimension analysis is conducted in turning operation. In this modeling and analysis, we extract features through 6th AR model, correlation integral and normalized correlation integral. After the back-propagation model of the neural network is utilized to monitor tool life according to flank wear. As a result. a very reliable classification of tool life was obtained.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.9
• /
• pp.63-68
• /
• 2004

The high pressure vessels that are constructed by welding process have many welding lines and most of the leakage defects are occurred on these welding lines. The acoustic emission(AE) technique has adopted to detect the defect location and leakage on welding parts, but the AE signal in leakage are incomplete due to the attenuation, reiteration, instability and limit of defect size. To overcome these troubles, the experiments in this study are conducted to measure the indirect media-propagated AE signal perpendicular to the leakage hole. The AE signals that are acquired from the direct and indirect media are analyzed, and the reliability of the indirect media-propagated AE signal are examined experimentally. By AE signal investigation, this method can be adopted to detect efficiently the leakage in welding parts.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.5
• /
• pp.60-66
• /
• 1996

Precision of bearing race is very important to maintain the clearance between ball and inner race. In internal grinding of bearing race, its roundness is dependent on shoe wear, accuracy of jig, dressing method and grinding conditions. In this study, the characteristics of shoe wear and eccentricity of workpiece were investigated experimentally. When wear of fornt shoe wear reaches at 100.mu. m and that of rear shoe reaches at 114 .mu. m, eccentricity of inner race is increased to 1.4 .mu. m. Roundness of race is mainly related to wear of rear shoe and ring type shoe is recommended to improve roundness of race.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.4
• /
• pp.216-226
• /
• 1993

Three dimensional cutting is considered as an equivalent orthogonal cutting through the plane containing both the cutting velocity vector and the chip flow velocity vector in dynamic cutting process. An analytical expression of dynamic cutting force is obtained from the cutting parameters determined by the static cutting. Particular attention is paid to the energy supplied to the vibratory system of cutting tool with two degree of freedom. In this approach, the phase lag of the horizontal vibration of the tool behind the vertical vibration and the direction angle of the fluctuating cutting force is considered in point of stability limits. Chatter vibration can be effectively suppressed by relatively increasing the spring constant and the damping coefficient of the cutting system in the vertical cutting force direction. A good agreement is found between the stability limits predicted by theoretical value and experimental results.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.4
• /
• pp.38-46
• /
• 1994

The vibration amplitude of boring bar is generally large at the tool tip, because it has the high length-diameter(L/D) ratio. A new dynamic cutting force model is presented by considering the change of shear angle under dynamic cutting. The boring bar is modelled as a cantilever with dynamic force acting at the tool end point. Based on this realistic continuous system model, the equation of motion of borring bar is solved by numerical computations. A good agreement is found between the proposed model and the experimental results.