• Korean Journal of Heritage: History & Science
• /
• v.43 no.3
• /
• pp.122-143
• /
• 2010

The Shilla Stone Monument in Jungseongri was found during the road-construction in Pohang. It has approximately two hundreds of letters inscribed on the surface of one side, and it is estimated to be older than Shilla Stone Monument in Naengsuri which had been known for the oldest stele in Shilla Period. This monument is made of fine to medium-grained biotite granite, while the Shilla Stone Monument in Naengsuri is made of fine-grained granodioritic porphyry bearing feldspar and amphibole phenocrysts. Both rock types of the monuments are interpreted to be cognate with biotite granite in Shinkwangmyeon, and with granodioritic porphyry in Gigyemyeon. They are characterized by xenolith and miarolitic cavity. Damage aspects in both monuments are discoloring, cracking and breaking. These damages do not cause structural instability of the monuments, but attenuate aesthetic value. Black and brown discoloring contaminants on the surface of the Jungseongri Monument contain a high amount of manganese and iron. As a result of ultrasonic test, both monuments were evaluated to be medium-weathered (MW), although the velocity of the Shilla Monument in Jungseongri was slightly lower than the Shilla Monument in Naengsuri. This is because the Monument in Juengseongri had been exposed to outdoor environment for long time until the discovery. It is necessary for Shilla Monuments to be protected by appropriately environmental control and management.

• The Journal of the Korea Contents Association
• /
• v.22 no.2
• /
• pp.58-70
• /
• 2022

The emergency preparedness exercise currently conducted by the government has been conducted as a message-based exercise for more than 50 years. Therefore, in this study, a simulation-based maintenance practice model was developed focusing on infectious disease situations, and the possibility of a training system applying scientific techniques was presented. As a result, First, a simulatioon logic assuming an infectious disease outbreak situation was developed. The situation of an infectious disease outbreak was made to occur when measures are not taken within 24 hours for the death due to disease, and when appropriate measures are not taken for contaminated food (24 hours), drinking water (12 hours), and drinking water shortage (24 hours). Second, in order to implement the simulation logic, simulation engine SW was developed for emergency medical team, epidemiological investigation team, dead burial team, quarantine and disinfection team, etc., and situation map SW was developed so that these contents could be expressed in the situation map. As suggested in this paper, if scientific techniques are applied to the simulation-based government practice model to expand the scope, training will be possible by creating practical situations that can occur in the real world, and the Chungmu plan and various emergency preparedness plans will be verified.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.2C
• /
• pp.109-117
• /
• 2010

Gas hydrate dissociation can generate large amounts of gas and water in gas hydrate bearing sediments, which may eventually escape from a soil skeleton and form voids within the sediments. The loss of fine particles between coarse particles or collapse of cementation due to water flow during heavy or continuous rainfall may form large voids within soil structure. In this study, the effect of void formation resulting from gas hydrate dissociation or loss of some particles within soil structure on the strength of soil is examined. Glass beads with uniform gradation were used to simulate a gas hydrate bearing or washable soil structure. Glass beads were mixed with 2% cement ratio and 7% water content and then compacted into a cylindrical sample with five equal layers. Empty capsules for medicine are used to mimic large voids, which are bigger than soil particle, and embedded into the middle of five equal layers. The number, direction, and length of capsules embedded into each layer vary. After two days curing, a series of unconfined compression tests is performed on the capsule-embedded cemented glass beads. Unconfined compressive strength of cemented glass beads with capsules depends on the volume, direction and length of capsules. The volume and cross section formed by voids are most important factors in strength. An unconfined compressive strength of a specimen with large voids decreases up to 35% of a specimen without void. The results of this study can be used to predict the strength degradation of gas hydrate bearing sediments in the long term after dissociation and loss of fine particles within soil structure.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.6 no.3
• /
• pp.147-175
• /
• 2011

The purpose of this study is to examine the effects of store choice criteria on customer satisfaction and store loyalty, and the moderating effects of customer emotions on the causal relationship between store choice criteria and customer satisfaction. In this regard, this study tries to identify the effects of store choice criteria on customer satisfaction and store loyalty in case of mass merchandisers, and to analyze the moderating effects of customer emotions on the causal relationship between store choice criteria and customer satisfaction. For this purpose, 300 customers, who have ever shopped at mass merchandisers, were surveyed and 246 valid responses were finally used for the data analysis. The results of this study are as follows. First, out of six store choice criteria, product factors, store reputation and physical environment turn out to have statistically significant effects on customer satisfaction. This result confirms those of the previous studies. On the other hand, store accessibility, subsidiary facilities and store atmosphere are not found to have statistically significant effects on customer satisfaction. This result is somewhat different from those of previous studies, and so further research on the subject needs to be carried out. Secondly, it turns out that customer satisfaction has a statistically significant effect on store loyalty, which is in line with the results of previous studies that perceived emotions affect customers' store attitudes which in turn influence their revisit intentions. Thirdly, as for the moderating effects of customer emotions on the relationship between store choice criteria and customer satisfaction, pleasure moderates the effects of store accessibility, subsidiary facilities and store atmosphere on customer satisfaction, arousal moderates the effects of product factors, subsidiary facilities and store reputation on customer satisfaction, and finally dominance moderates the effects of product factors and subsidiary facilities on customer satisfaction. These findings partially support the results of previous studies that customers' in-store emotional experiences such as feeling good or bad enhance their store loyalty.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.20 no.1
• /
• pp.53-62
• /
• 2015

To elucidate the microbial consortia responsible for the anaerobic methane oxidation in the methane hydrate bearing sediments, we compared the geochemical constituents of the sediment, the rate of sulfate reduction, and microbial biomass and diversity using an analysis of functional genes associated with the anaerobic methane oxidation and sulfate reduction between chimney site (UBGH2-3) on the continental slope and non-chimney site (UBGH2-10) on the basin of the Ulleung Basin. From the vertical profiles of geochemical constituents, sulfate and methane transition zone (SMTZ) was clearly defined between 0.5 and 1.5 mbsf (meters below seafloor) in the UBGH2-3, and between 6 and 7 mbsf at the UBGH2-10. At the UBGH2-3, the sulfate reduction rate (SRR) in the SMTZ exhibited was appeared to be $1.82nmol\;cm^{-3}d^{-1}$ at the depth of 1.15 mbsf. The SRR in the UBHG2-10 showed a highest value ($4.29nmol\;cm^{-3}d^{-1}$) at the SMTZ. The 16S rRNA gene copy numbers of total Prokaryotes, mcrA, (methyl coenzyme M reductase subunit A), and dsrA (dissimilatory sulfite reductase subunit A) showed the peaks in the SMTZ at both sites, but the maximum mcrA gene copy number of the UBGH2-10 appeared below the SMTZ (9.8 mbsf). ANME-1 was a predominant ANME (Anaerobic MEthanotroph) group in both SMTZs of the UBGH2-3 and -10. However, The sequences of ANME-2 were detected only at 2.2 mbsf of the UBGH2-3 where high methane flux was observed because of massive amount of gas hydrate at shallow depth. And Desulfosarcina-Desulfococcus (DSS) that is associated with ANME-2 was detected in 2.2 mbsf of the UBHG2-3. Overall results demonstrate that ANME-1 and ANME-2 are considered as significant archaeal groups related to methane cycle in the subsurface sediment of the East Sea, and ANME-2/DSS consortia might be more responsible for methane oxidation in the methane seeping region than in non-seeping region.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.36 no.4
• /
• pp.58-69
• /
• 2018

The purpose of this study was to present specific standards for landscape planning and construction applicable to landscaping areas in various historical sites. The results are as follows: First, the types of historical sites are classified according to their preservation status and processing techniques, and the classification according to their status is divided into those that have been buried underground, such as those that have been exposed to the ground, such as buildings and structures, and those that have a reputation or a record of the sites. The classification according to the wartime processing technique was classified by such techniques as closures that isolate the site, penetration that can be seen on the site, and overlays where a separate protection facility is installed on the site. Second, the principles of landscape planning for display of historical sites are divided into the items that make up the historical site, surface treatment of the sites, tree planting, and installation of facilities. If the site is not a circular space, the area separating the space by different materials between the components is required. In the event that preservation of the historical site is required, it is deemed desirable to use the soil, and to do so, the use of grasses and shrubs is effectively considered to be effective. The introduction of plants and plants should be considered according to the nature of the space. Depending on the area and nature of the monument, the facility is required to take a cautious approach by reviewing its influence on the landscape and the additional excavation of the monument. Third, the readjustment method derived as a result of looking at the landscaping principle in the historical site space was classified as conservation of status, installation of protection facilities, burial, restoration, relocation, and reproduction. Preservation of the status quo is essential for limited landscape planning and should not affect the prototype of existing relics. The protection facility shall be installed where necessary to protect the relics, and when the soil is formed, the surface treatment shall be required to remove trees that could damage the site and prevent soil and soil oil from being lost after the site. The restoration shall establish a landscaping plan according to the circular preservation based on the clues to the circle. The transfer requires a landscaping plan to create an environment similar to the outer space of an existing site and should be able to highlight the value or location of the original site. The reenactment should have a landscaping plan to revive the landscape and atmosphere of the past for the now-defunct remains. Fourth, landscaping can simultaneously satisfy the preservation of excavation sites and the increase in exhibition effects. In order to protect the traces of the past and vitalize the site of the ruins today, specific measures are required, the creation of a park for historical sites that preserve the functions and value of the relics, and the formation of a shape of linked contents can be suggested as alternatives.

• Korean Journal of Heritage: History & Science
• /
• v.53 no.4
• /
• pp.170-187
• /
• 2020

Dolmens bearing the burial layout and stone coffin tombs of the late Bronze Age were excavated from Samdeok-ri, Goseong, Gyeonsangnsamdo, and grave items such as red-burnished pottery, arrowheads, and stone swords were also discovered. In the case of the red-burnished pottery that was found, it retains a pigment layer with a thickness of about 50 to 160㎛, but with most of the other items, exfoliation and peeling-off of pigment layers can be observed on the surface. The raw materials of the red-burnished pottery contained moderately sorted minerals such as quartz, feldspar, and hornblende, and partly opaque iron oxide minerals were also identified. In particular, the raw materials of the red-burnished pottery from stone coffin tomb #6 were different from those of the other pottery, containing large amounts of hornblende and feldspar. The pottery's red pigment was identified as hematite and showed similar mineral content of raw materials such as fine grained quartz, feldspar, and hornblende. The firing temperature is estimated to have been approximately 900℃, based on their mineral phase. The possibility exists that the raw materials had been collected from the Samdeok-ri area, because diorite and granite diorite with dominant feldspar and hornblende have been identified within 3km of that area. During the pottery manufacturing process, it is estimated that the pigment was painted on the entire surface of the red-burnished pottery after it had been molded and then finished using the abrasion technique. In other words, the red-burnished pottery was made by the process of vessel forming - semi drying - coloring - polishing. The surface and cross-section of the pottery appears differently depending on the concentration of the pigment and the coloring method used after vessels were formed. Most of the excavated pottery features a distinct boundary between pigment and body fabric. However, in the case of pottery in which fine-grained pigments penetrate the body fabric so that layers cannot be distinguished, there is the possibility that the fine-grained pigment layer was applied at a low concentration or immediately after vessel forming. Many cracks can be seen on the surface pigments in thickly painted pottery items, and in many cases, only a small portion of the pigment layers remain due to surface exfoliation and abrasion in the burial environment. It is reported that pottery items may be more easily damaged by abrasion if coated with pigment and polished, so it is believed that the red-burnished pottery of the Samdeok-ri site suffered from weathering in the burial environment. This damage was more extensive in the potsherds that were scattered outside the tomb.

• Korean Journal of Heritage: History & Science
• /
• v.56 no.3
• /
• pp.174-193
• /
• 2023

Korea is surrounded by the sea and has rivers connecting to it throughout the inland areas, which has been a geographical characteristic since ancient times. As a result, there have been exchanges and conflicts with various countries through the sea, and rivers have facilitated the transportation of ships carrying grain, goods paid for by taxes, and passengers. Since the past, the sea and rivers have had a significant impact on the lives of Koreans. Consequently, it is expected that there are many cultural heritages submerged in the sea and rivers, and continuous efforts are being made to discover and preserve them. Underwater cultural heritage is difficult to discover due to its location in the sea or rivers, making direct visual observation and exploration challenging. To overcome these limitations, various geophysical survey techniques are employed. Geophysical survey methods utilize the physical properties of elastic waves, including their reflection and refraction, to conduct surveys such as bathymetry, underwater topography and strata. These techniques detect the physical characteristics of underwater objects and seafloor formation in the underwater environment, analyze differences, and identify underwater cultural heritage located on or buried in the seabed. Bathymetry uses an echo sounder, and an underwater topography survey uses a side-scan sonar to find underwater artifacts lying on or partially exposed to the seabed, and a marine shallow strata survey uses a sub-bottom profiler to find underwater heritages buried in the seabed. However, the underwater cultural heritage discovered in domestic waters thus far has largely been accidental findings by fishermen, divers, or octopus hunters. This study aims to analyze and summarize the latest research trends in equipment used for underwater cultural heritage exploration, including bathymetric surveys, underwater topography surveys and strata surveys. The goal is to contribute to research on underwater cultural heritage investigation in the domestic context.

• Korean Journal of Heritage: History & Science
• /
• v.46 no.3
• /
• pp.114-133
• /
• 2013

This study aims to identify the natural damage of the Samcheonsaji Temple Site in Bukhansan National Park and to suggest the plans to minimize damage for the remains. The types of natural damage are classified into direct vegetation damage, indirect topographical damage, and artificial damage. The most popular causes of damage to temple sites include the roots of trees as direct vegetation damage and the soil erosion by rain or stream as topographical damage. Direct vegetation damage includes burial remains damaged by the root of trees and vines, but it is often observed that some trees have contributed to protection against collapse. Indirect topographical changes have damaged the ruins by soil erosion caused by floods or typhoons. Vegetation changes due to topographical reasons have also caused damage. Artificial reasons of damage include forestry operations and compaction by hikers. Based on the analysis of the findings, the following could be suggested as plans to resolve these problems: 1. Natural damage occurs slowly due to negligence. Therefore, it could be reduced by forestry improvement, including forest density control through thinning, planting to prevent landslides, maintaining grasslands nearby. 2. Deciduous broadleaf trees can be planted to reduce soil erosion by rainfall. It is necessary to maintain the density of forests at around $0.02{\sim}0.18trees/m^2$. 3. It would be good to grow Quercus spp and Carpinus spp or weaken the community of Robinia pseudoacacia and Pueraria lobata which disturb the ecosystem. Samcheonsaji Temple Site is located in Mt. Bukhan National Park that is a publicly owned property. Therefore, it is constantly maintained for natural preservation and vegetation management could be considered for the preservation of historical remains.

• Clean Technology
• /
• v.29 no.4
• /
• pp.288-296
• /
• 2023

Coal is abundantly available compared to other energy sources and is used as a versatile energy resource worldwide. To address the environmental issues stemming from conventional coal utilization, efforts are underway to develop clean coal utilization technologies, with IGCC technology being a notable example. In IGCC plants, coal is subjected to a CMD process where both drying and pulverization are achieved by supplying hot air. However, if the temperature of the supplied hot air is excessively high, it can lead to devolatilization and spontaneous combustion, thereby compromising the stable operation of the CMD process. This study aimed to measure the devolatilization and spontaneous combustion temperatures of different types of bituminous coal, and to explore their correlations with the characteristics of the coals. Six coal types exhibited devolatilization between 350 and 400 ℃, while three coal types showed devolatilization at temperatures exceeding 400 ℃. Spontaneous combustion ℃curred in one coal type below 100 ℃, six coal types between 100 and 150 ℃, and two coal types above 150 ℃. The measured initiation temperatures were compared with the coal characteristics including the oxygen, moisture, Fe₂O₃, and CaO content, the H/C ratio, and the O/C ratio to establish correlations. Regression analysis was used to calculate the regression coefficients and determination coefficients for each ignition temperature. It was found that 52.44% of the FC/VM data significantly influenced the volatile matter ignition temperature, and 59.10% of the Fe₂O₃ data significantly affected the spontaneous combustionignition temperature.