• Journal of dental hygiene science
• /
• v.15 no.1
• /
• pp.38-45
• /
• 2015

This research was attempted in order to investigate the correlation of the conflict level and job satisfaction of the dental hygienists in the dental clinic agency. The subjects were 249 dental hygienists working with more than five dental hygienists at dental clinics in Daegu, eight dental clinics were randomly chosen, the researcher visited them personally and the data was obtained by self-administrated questionnaires from March 2 to March 31, 2011. In conclusion, the higher ages, monthly income and total career were, the higher levels of conflict were, and job satisfaction was significantly high when monthly income and total career were higher. Correlation between level of conflict and job satisfaction showed as level of conflict are lower, job satisfaction was significantly high. Regression analysis of the factors affecting job satisfaction, it was significantly high as monthly income was higher, friction of view and ignorance was lower. Therefore, the conflict level is reduced, the job satisfaction degree of the dental hygienist is enhanced, the dental hygienist duty efficiency is enhanced and dental service of the good quality is provided.

• Journal of Power System Engineering
• /
• v.15 no.3
• /
• pp.31-37
• /
• 2011

직조 금속 스크린 리브(rib) 이 바닥에 설치된 사각 덕트에서 열전달과 유체유동의 압력강하를 측정하기 위해 실험적 연구를 수행하였다. 시험부의 치수는 200 mm(W) ${\times}$ 40 mm(H) ${\times}$ 712 mm(L)이고 수력직경은 66.6 mm이다. 입구영역에는 1.72m 길이의 가열되지 않은 동일한 치수의 채널을 설치하였다. 메쉬가 다른 4가지의 직조금속 스크린 리브에 대해 측정하였다. 그리고 비교를 위해 일체형 리브에 대해서도 측정하였다. 국부 열전달 계수의 측정에는 스테인레스 강제 포일(foil) 히터와 T형 열전대률 이용하였다. 레이놀즈 수는 23,000에서 58,000의 범위이다. 덕트의 수력직경($D_h$)에 대한 직조 금속 리브의 높이(e)의 비($e/D_h$)는 0.075 이고 리브 간격(p)과 높이의 비(p/e)는 10이다. 실험 결과 메쉬가 없는 일체형 리입에서 가장 누셀트 수와 마찰계수가 컷다.

• Nuclear Engineering and Technology
• /
• v.26 no.1
• /
• pp.108-118
• /
• 1994

A semi-empirical correlation has been developed for adiabatic interfacial friction factors in a long horizontal air-water countercurrent stratified flow conditions. Using a pipe and duct test sections, a series of experiments hate been conducted varying non-dimensional water depth and flow rates of air. On the basis of simultaneous measurement of the main flow parameters in a horizontal pipe and a duct, a semi-empirical correlation for the interfacial friction factor in a stratified flow regime has been developed employing a new concept of surface roughness in wavy flow. A total of 201 data point, including 15 concurrent pipe flow test data of others, have been used in the present analysis. A comparison between the data and the predictions of the present correlation shows that the agreement is within $\pm$30%.

• Journal of the Korean Society for Railway
• /
• v.16 no.4
• /
• pp.253-261
• /
• 2013

According to the measured results of KTX brake squeal noise in this study, high level brake noise occurred in a wide frequency range, 100~18,000Hz. To identify the sources of the brake squeal noise, unstable vibration modes due to brake disc/pad interaction were analyzed under various conditions by the finite element method. Complex eigenvalues for a brake unit with a disc and four pads were obtained. It was found that the real parts of the complex eigenvalues, that is, unstable vibration modes, were closely related to friction coefficients, pressure on the brake cylinders, elastic moduli of the components, and other conditions.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2002.02a
• /
• pp.257-262
• /
• 2002

본 연구에서는 분쇄방법에 따른 감초 분쇄생성물의 특성을 분석한 결과는 다음과 같다. 1. Hammer mill의 경우 d$_{80}$=750$\mu\textrm{m}$로 중간미분쇄의 입도범위를 가지며 비표면적은 0.269m/g로 분석되었고, Pin mill의 경우 d$_{80}$=600$\mu\textrm{m}$로 Hammer mill보다 입자크기는 조금 작으나 중간미분쇄영역의 입도범위를 가지며 비표면적은 0.324m$^2$/g로 분석되었고, Turbo mill은 d$_{80}$=250$\mu\textrm{m}$와 비표면적은 0.370m$^2$/g로 입자의 크기가 가장 작아 다른 분쇄기보다 분쇄능이 가장 우수한 것으로 분석되었다. 2. Hammer mill의 분쇄메커니즘은 대부분 충격, 일부 전단과 마찰에 의해 분쇄가 행해지고, Pin mill은 핀 사이에서의 전단, 충격, 마찰에 의해 분쇄된다. 즉 충격과 마찰에 의한 분쇄는 전단력에 의한 분쇄메커니즘보다 분쇄 능이나 분쇄효율이 상대적으로 낮은 것을 알 수 있었으며 주로 전단력과 충격, 반발력에 의해 분쇄가 이루어지는 Turbo mill의 분쇄능 및 분쇄 효율이 우수함을 알 수 있었다. 본 연구에 의해서 감초와 같이 섬유질을 많이 함유하고 있는 원료를 분쇄할 경우 분쇄메커니즘이 전단력인 분쇄기가 가장 적합하고, 분쇄중 소요되는 동력 면에서도 기존 분쇄기보다 우수한 Turbo mill의 분쇄조건을 확립해야 한다고 사료된다. 사료된다.

• Journal of Korean Society of Steel Construction
• /
• v.18 no.2
• /
• pp.181-189
• /
• 2006

This study analyzes the effects of the curvature friction coefficient, the wobble friction coefficient, and the increased strength of concrete, reinforced tendon on optimum de signs by using the optimum-design program, to minimize the cost of a PSC box girder bridge using the full staging method. The objective of this study is to find a proper tendon for the friction coefficient, and thereafter, to indicate the direction of the study development about tendons and to indicate the direction of a study on the increased strength of used materials. This program used the SUMT procedure and Kavlie's extended-penalty function to allow infeasible design points in the process. Powel's direct method was used in searching design points, and the gradient approximate method was used to reduce the design hours.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.23 no.2
• /
• pp.199-208
• /
• 2010

A friction damper installed at a building shows nonlinear behavior since its stick and slip states are occurred repeatedly depending on the amplitude of external loadings to dissipate input energy. Friction damping is existed for the building with a friction damper. In additionally viscous one is inherently included. Therefore, the building installed in such combined damping is quite involved to find the analytical solution. In this study, first, displacement and acceleration characteristics are identified based on the exact solution for a single-degree-freedom building with a friction damper having both friction and viscous damping. Second, in free vibration, the equivalent viscous damping ratio is obtained by the energy dissipation. Third, numerical analysis is carried out to find response configuration with various friction force ratios. Fourth, corresponding equivalent viscous damping ratio is derived with the finding that the response reaches into steady-state for both friction and viscous damped structure. It is deduced using balance of input external energy and output dissipation energy for steady-state response. Finally, the equivalent viscous damping ratios of free or harmonic vibration are verified through nonlinear analysis.

• Journal of Energy Engineering
• /
• v.12 no.2
• /
• pp.131-138
• /
• 2003

This paper considered the structural mechanism of transitional boundary layer by the experimental approach. In order to measure the turbulence quantity in the boundary layer, we made a wind tunnel with 400${\times}$190${\times}$2500 mm test section and a flat plate with well fabricated leading edge. Hot wire anemometer was used for acquiring the continuous turbulence signal which is processed by special software. The results of experiment show that the region where turbulence spot is dominant moves from near wall to overall layer and thus the anisotropy of velocity fluctuation shows so large value. Also the turbulence energy originally contained in low frequency band comes up to the high frequency band. Finally the turbulence model needs minimum two length scales to consider the pre-transition region.

• Transactions of the Society of Information Storage Systems
• /
• v.11 no.1
• /
• pp.11-15
• /
• 2015

In HDD industry, many technologies have been developed and investigated as means to increase the areal density of drives. Thermal flying-height control has been considered and widely applied in current HDD. When contact occur between TFC slider and disk, the slider has a friction heating induced by highly rotated disk. Moreover, because of the friction heating, additional protrusion of slider can occur. The additional protrusion in contact situation can be a severe effect on head part of slider and disk. Therefore, in this paper, we analyze the friction heating and additional protrusion in contact situation.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.337-341
• /
• 2004

Bulk metallic glasses(BMG) with good mechanical properties have problems that engineering application fields have been limited because of limitation of the alloy size. In order to solving this problem, the friction welding of BMG has been tried using the superplastic-like deformation behavior under the supercooled liquid region. The apparatus for friction welding test was designed and constructed using pneumatic cylinder and gripper based on a conventional lathe. Friction welding have been tried to combination of same BMG alloy and crystalline alloys. The results of welding test were evaluated by X-ray diffraction, measurement of hardness and mechanical properties test. In order to obtain the optimized welding test conditions the temperature of friction interface was measured using Infrared thermal imager.