• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.8
• /
• pp.1137-1143
• /
• 2009

Experiments were conducted to evaluate pool boiling heat transfer performance between plain and micro finned surfaces with FC-72, which is chemically and electrically stable. Three kinds of micro fins with the dimension of $100{\mu}m\;{\times}\;10{\mu}m$, $150{\mu}m\;{\times}\;10{\mu}m$ and $200{\mu}m\;{\times}\;10{\mu}m$ (width $\times$ height) were fabricated on the surface of a silicon chip. The experiments were carried out on the liquid subcooling of 5, 10 and 15 K under the atmospheric condition. The micro finned surface with a larger fin width of $200{\mu}m$ provided a better pool boiling heat transfer performance. Also, the micro finned surfaces showed a sharp increase in heat flux with increasing wall superheat and a larger heat transfer enhancement compared to a plain surface.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.9
• /
• pp.761-772
• /
• 2015

Microfin tubes having an outside diameter (O.D.) of 7.0 mm are widely used in residential air conditioning systems and heat pumps. It is known that the mass fluxes for air conditioners and heat pumps under partial load conditions are several tens of $kg/m^2s$. However, literature surveys reveal that previous investigations were limited to mass flux over $100kg/m^2s$. In this study, we conduct R-410A evaporation heat-transfer tests at low mass fluxes ($50-250kg/m^2s$) using a 7.0 mm O.D. microfin tube. During the test, the saturation temperature was maintained at $8^{\circ}C$, and the heat flux was maintained at $4.0kW/m^2$. For comparison purposes, we also test a smooth tube with a 7.0 mm O.D. The results showed that the heat-transfer enhancement factor of the microfin tube increased as the mass flux decreased up to $150kg/m^2s$, which decreased as the mass flux further decreased. The reason for this was attributed to the change of the flow pattern from an annular flow to a stratified flow. Within the test range, the frictional pressure drops of the microfin tube were approximately the same as those of the smooth tube. We then compare experimental data obtained with the predictions obtained for the existing correlations.

• Proceedings of the KSME Conference
• /
• 2005.11a
• /
• pp.20.1-20.1
• /
• 2005

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.10
• /
• pp.1089-1095
• /
• 2011

Numerical simulation is performed for nucleate boiling on a micro-finned surface, which has been widely used to enhance heat transfer, by solving the equations governing the conservation of mass, momentum, and energy in the liquid and vapor phases. The bubble motion is determined by a sharp-interface level-set method, which is modified to include the effect of phase change and to treat the no-slip and contact-angle conditions, as well as the evaporative heat flux from the liquid microlayer on immersed solid surfaces such as micro fins and cavities. The numerical results for bubble formation, growth, and departure on a microstructured surface including fins and cavities show that the bubble behavior during nucleate boiling is significantly influenced by the fin-cavity arrangement and the fin-fin spacing.

• Applied Chemistry for Engineering
• /
• v.16 no.4
• /
• pp.588-593
• /
• 2005

In this study, biodegradable poly(${\varepsilon}$-caprolactone) (PCL) microcapsules containing chemically treated $SiO_2$ and nifedipine were prepared by oil-in-water (O/W) emulsion solvent evaporation method. The microcapsules containing drugs were confirmed using FT-IR spectra. The morphologies of the microcapsules were observed with scanning electron microscope (SEM). The nifedipine's release behaviors from the microcapsules were also examined with UV/vis spectroscopy. As a result, the inclusion of nifedipine into the microcapsules was determined by the presence of nifedipine's specific peak, i.e., C=O stretch vibration at $1682cm^{-1}$. The average particle size of the microcapsules decreased with increasing stirring rate. The nifedipine adsorption capacity and release rate of treated $SiO_2$ that was treated with basic solution decreased because with the increased basicity it lowered the specific surface area of $SiO_2$ and promoted stronger acid-base interactions between $SiO_2$ and nifedipine.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.123-123
• /
• 2018

최근 웨어러블 디바이스에 연구가 집중되면서 투명하고 유연한 마이크로 히터의 필요성이 증가되고 있다. 그럼에도 불구하고, 기존의 사용되는 마이크로 히터들은 딱딱하고 불투명하다. 게다가, 기존의 금속성의 마이크로 히터들의 경우 저항이 너무 작아 웨어러블 디바이스에 사용되는 에너지 하베스터로 구동되기에 효율이 떨어지는 경향이 있다. 이 논문에서 우리는 CVD 방식으로 성장된 그래핀으로 열 발생 라인을 패시베이션 레이어로 h-BN을 이용하여 투명하고 유연한 마이크로 히터를 제작하였다. 제작한 마이크로 히터는 균일한 온도 분포와 200도까지의 온도 상승에 걸리는 시간이 4초 정도로 굉장히 좋은 성능을 보유하고 있다. 또한 소비 전력은 39mW 이하로 효율적이다. 또한 기존의 메탈릭 히터에 비해 저항이 굉장히 높기 때문에 웨어러블 에너지 하베스터로 작동하기 적합하다. 또한 미래의 휴대용/웨어러블 개인 전자기기와 무선 헬스케어 제품, 휴대용 환경 센서에도 적용될 것으로 기대한다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.11
• /
• pp.1139-1145
• /
• 2011

An automated anastomotic ring-pin system consisting of both the anastomotic ring-pin system and the coupler device has eliminated the drawbacks of the suture method. High density polyethylene (HDPE), a material with outstanding biocompatibility and injection molding capability, was used in the ring. SUS316 stainless steel, Ti-6Al-4Nb, Ti-6Al-4V, and unalloyed titanium were used in FEM simulations of the micropin. The authors categorized the microvascular anastomotic ring micropins into short neck (SN) and long neck (LN) groups in order to evaluate the effect of the micropin's fillet radius and neck length on the von Mises stress. The micropins were further divided into those with and without fillet. On the basis of the fillet radius rate (FRR), which represents the rate of change in the von Mises stress with respect to the availability and shape of the fillet, and the neck length rate (NLR), which represents the rate of change in the von Mises stress with respect to changes in the length of the neck within the fillet shape, it can be concluded that the SN-3 neck design is the most stable.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.4
• /
• pp.50-57
• /
• 2017

In the injection molding process, a core that builds a space for a product is installed at the internal place in the mold and fabricated as the frame of the mold. In this make up, the fabricating partial form of the mold at a pin is a core pin. The core pin is finer because an injection mold produces miniaturization and integration. On the other hand, when the core is manufactured using the existing centerless grinder, it generates vibrations because of the lack of a fixed zig for a micro size workpiece. For this reason, an existing centerless grinder without a micron size fixed zig, makes a defective product due to vibration and deformation. In this study, a compact grinding system that can be installed using an existing centerless grinder was fabricated to make a micro size core pin. Using the compact grinding system, grinding experiment for core pin was carried out. The performance of the system was confirmed by measuring the surface roughness, roundness, and cylindricity.

• Journal of the Microelectronics and Packaging Society
• /
• v.30 no.2
• /
• pp.60-64
• /
• 2023

In this study, the electrical contact resistance characteristics between graphene and metals, which is one of important factors for the performance of graphene-based devices, were compared. High-quality graphene was synthesized by chemical vapor deposition (CVD) method, and Al, Cu, Ni, and Ti as electrode materials were deposited on the graphene surface with equal thickness of 50 nm. The contact resistances of graphene transferred to SiO₂/Si substrates and metals were measured by the transfer length method (TLM), and the average contact resistances of Al, Cu, Ni, and Ti were found to be 345 Ω, 553 Ω, 110 Ω, and 174 Ω, respectively. It was found that Ni and Ti, which form chemical bonds with graphene, have relatively lower contact resistances compared to Al and Cu, which have physical adsorption properties. The results of this study on the electrical properties between graphene and metals are expected to contribute to the realization of high-performance graphene-based devices including electronics, optoelectronic devices, and sensors by forming low contact resistance with electrodes.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.1
• /
• pp.67-71
• /
• 2021

In this study, graphene layer was grown on metal microwire using chemical vapor deposition. The difference of carbon solubility between copper and nickel resulted in the formation of mono-layer and multi-layer graphene were formed on the surfaces of copper and nickel microwires, respectively. During the growth of graphene at high temperature, copper and nickel were recrytallized and the grain size increased. The ampacity of graphene/copper microwire was improved by approximately 27%, 1.91×105 A/㎠, compared to pristine copper microwire. Similar to this behavior, the ampacity of multilayer graphene/nickel microwire was 4.41×104 A/㎠ which is about about 36% improved compared to the pure nickel microwire. The excellent electrical properties of graphene/metal composites are beneficial for supplying the electrical energy to the high-power electronic devices and equipment.