• Journal of Advanced Engineering and Technology
• /
• v.5 no.4
• /
• pp.349-353
• /
• 2012

Recently, Mobile multimedia equipments as smart phone and tablet pc requirement is increasing and this market is also being expanded. These mobile equipments require large multi-media function, so more power consumption is required. For these reasons, the needs of power management IC as switching type dc-dc converter and linear regulator have increased. DC-DC buck converter become more important in power management IC because the operating voltage of VLSI system is very low comparing to lithium-ion battery voltage. There are many people to be concerned about digital DC-DC converter without using external passive device recently. Digital controlled DC-DC converter is essential in mobile application to various external circumstance. This paper proposes the DC-DC Buck Converter using the AVR RISC 8-bit micro-processor control. The designed converter receives the input DC 18-30 [V] and the output voltage of DC-DC Converter changes by the feedback circuit using the A/D conversion function. Duty ratio is adjusted to maintain a constant output voltage 12 [V]. Proposed converter using the micro-processor control was compared to a typical boost converter. As a result, the current loss in the proposed converter was reduced about 10.7%. Input voltage and output voltage can be displayed on the LCD display to see the status of the operation.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.7 no.3
• /
• pp.27-33
• /
• 1993

This paper presents the &tal controller for driving high frequency voltage fed PWM inverter that carrier frequency is over 2OkHz.We analyzed the conventional PWM to select a proper PWM pattern. as the result, obtained PWM pattern of the controller in which asynchronus staircase sinusoidal waveform is used as reference signal, and variable carrier ratio method was used for PWM control. The PWM controller is designed by fully digital method. Especially, Thk proposed controller is consisted of 8 bit one-chip microprocessor and digital logic. the former is for arithmetic and data processing, and the latter is for PWM pattern synthesis. Therefore, The responsibility and controllability is improved. Also, Data processing capability is improved using proper program to output modulation index with 9 bits. Circuits configuration of digital controller are made up of one chip 8051 and EPLD, and its controllability is tested by operating voltage fed inverter. Harmonics and current waveform is evaluated and analyzed for the voltage fed inverter system.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.44 no.1
• /
• pp.12-18
• /
• 2007

As an arc fault interrupter, the AFCI mentioned in this paper has been designed to detect and interrupt arc faults due to wire deterioration, insulation, wire damage, loose connection, and excessive mechanical damage. Since AFCI is digital and uses mechanical and electric stress, the length of interruption against overload and over-current is much shorter than the current bi-metal method. Therefore, the risk of electrical fires has been reduced.

• Journal of Advanced Navigation Technology
• /
• v.14 no.2
• /
• pp.227-232
• /
• 2010

According to the development of ubiquitous and computer techniques, the application fields of sensor network have been enlarged. We present the design and implementation of sensor node which is the most important component of sensor network techniques in this paper. The proposed sensor node is implemented with 8-bit microprocessor, and temperature and humidity sensing device to gather temperature and humidity data in real world. It achieves low production cost and user convenience, and also has the feature os existing commercial sensor node. Though our experiments, we show that deviation of temperature and humidity are $5^{\circ}C$ and 23.2% respectively, and the proposed sensor node is reliable in real applications.

• Journal of Convergence for Information Technology
• /
• v.9 no.10
• /
• pp.101-107
• /
• 2019

This paper proposes a method for detecting faults in conveyor systems used for transportation of raw materials needed in the thermal power plant and cement industries. A small drone was designed in consideration of the difficulty in accessing the industrial site and the need to use it in wide industrial site. In order to apply the system to the embedded microprocessor, hardware and algorithms considering limited memory and execution time have been proposed. At this time, the failure determination method measures the peak frequency through the measurement, detects the continuity of the high frequency, and performs the failure diagnosis with the high frequency components of noise. The proposed system consists of experimental environment based on the data obtained from the actual thermal power plant, and it is confirmed that the proposed system is useful by conducting virtual environment experiments with the drone designed system. In the future, further research is needed to improve the drone's flight stability and to improve discrimination performance by using more intelligent methods of fault frequency.

• Journal of Advanced Navigation Technology
• /
• v.27 no.2
• /
• pp.197-202
• /
• 2023

This paper presents the design method and electrical characteristics of a high-efficiency power amplifier for a 50 Watts class repeater applied to a 5G system and used in in-building, subway, and tunnel. GaN was used for the termination transistor of the power amplifier designed here, and intermodulation signals were removed using DPD to satisfy linearity. In addition, in order to handle various requirements such as amplifier gain control and alarm processing required in the 5G system, the microprocessor is designed to exist inside the power amplifier. The amplifier manufactured to confirm the electrical performance of the power amplifier satisfying these conditions satisfied 46.5 dBm and the overall efficiency of the amplifier was 37%, and it was confirmed that it satisfied various alarm conditions and electrical characteristics required by telecommunication companies.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1997.05a
• /
• pp.207-212
• /
• 1997

영광2호기에 설치되어있는 노내 중성자속 감시 계통 설비인 기계식 인출제한 스위치(Withdrawl Limit Switch)의 구조적인 결함을 제거하기 위한 원인 분석 및 개선과정에 중점을 두었다. 기계제어방식의 구조적 결함은 검출기(Detector)가 노심의 중성자속(Neutron Flux)을 측정하기 위해 구동기의 수동 혹은 자동운전시 검출기 안내관에 삽입 인출이 반복 수행되면서 물리적 또는 환경적요인에 의한 레버의 휘어짐으로 접촉위치의 변경이 발생하는 것을 의미한다. 콘솔내 다수의 마이크로-프로세서(Multiple-Microprocessors)에 의한 구동기(Drive Unit) 동작으로 노심내 3차원 중성자속 분포를 측정할 수 있는 유일할 설비로써 본 계통은 그동안 관련 보수작업 및 설비개선에도 불구하고 근본문제점이 해소되지 못한 가운데 여러차례의 설계, 모의시험을 거쳐 인출제한스위치 제어 방식을 기계식에서 전자식으로 개선, 대체하여 시험 및 운전해 본 결과 근본적 결함원인이 해결되었음을 확인하였다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.3
• /
• pp.581-590
• /
• 2001

This paper has been studied about supply of optical source of laser diode with stable and uniform output wavelength in optical transmission system. The stabilized constant current circuit is designed. The temperature control circuit is constructed for the control of internal temperature of laser diode. Also, the wavelength locker is used in optical output. Finally, A/D, D/A converter and micro-processor are used for the control of temperature.

• Proceedings of the KIEE Conference
• /
• 1988.11a
• /
• pp.321-324
• /
• 1988

This paper presents the result of driving performance analysis of PMSM type AC servo motor based on control system using a microprocessor. The experiment using the microprocessor is tested with a 120[v], 200[w] PMSM type AC servo motor. The PWM signal generated in the microprocessor for the servo motor voltage is chapped by power transistor modules to change the AC servo motor speed. The torque of the AC servo motor with a permanent magnet can be easily controlled over a wide range by changing the AC servo motor current.

• The Journal of the Korean dental association
• /
• v.22 no.12 s.187
• /
• pp.1075-1082
• /
• 1984

The measurement of the silent period of Masseter muscle is very useful diagnostic method of TMJ syndrome. In this paper, we design a very convenient and very low-priced medical instrument for dental research which does not need gain control to each patient for measuring the silent period and the data processing time is very short.