• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.11 s.114
• /
• pp.1040-1049
• /
• 2006

A design method for minimizing transmission loss of a broadband right-angle transition from a coaxial cable to a microstrip line is presented. The right-angle transition has been widely used where printed circuit applications need to be fed from behind the ground plane using coaxial line. To obtain the minimized transmission loss over the whole operating frequency range of the transition, design parameters such as ground aperture and probe diameters, ground aperture offset, and stub length are optimized using a commercial electromagnetic simulation software. Results are presented for the optimum right-angle transition from an SMA connector to a microstrip line on common reinforced 0.787 mm thick PTFE substrates. Measurements of a fabricated transition show that reflection coefficient is less than -22 dB and insertion loss is less than 0.45 dB over $0.05{\sim}20GHz$.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 1996.10a
• /
• pp.1181-1184
• /
• 1996

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.7
• /
• pp.727-733
• /
• 2003

In order to realize miniaturized and low-impedance MMIC passive component, a novel microstripline structure employing periodically perforated ground metal was proposed. The novel microstripline structure showed much lower impedance, and shorter guided-wavelength than conventional one. Using the novel microstripline with periodically perforated ground metal, a miniaturized 15 $\Omega$ ratrace was fabricated. The line width of the ratrace was 20 $\mu\textrm{m}$, and the size of it was 0.375 mm$^2$, which is 9.3 % of conventional one. The ratrace exhibited good RF performances from 20 to 30 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.5
• /
• pp.713-721
• /
• 2001

In this paper, parasitic patches gap-coupled microstrip antenna and stacked microstrip patch antenna combined with parallel coupled lines, which are a kind of wideband impedance matching network, are proposed to get the wider bandwidth. The iterative method using a distributed network is proposed to design the parallel coupled lines as a wideband impedance matching network. Measurements show that the proposed antennas provide wider bandwidths ~1.6 times and ~1.5 times those of conventional parasitic gap-coupled microstrip patch antenna and stacked microstrip patch antenna. In addition, measured radiation patterns show no serious variation of radiation patterns though the parallel coupled lines is added. The antenna gain is, however, lowered about 1 dB and 0.5 dB by the coupling loss in the parallel coupled lines.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.3
• /
• pp.305-316
• /
• 1998

The impedance matching network with the simplfied real frequency technique (SRFT) is proposed as a method for bandwidth enhancement of microstrip antenna. The validity of the technique is based on the relative frequency insensitivity of the radiation pattern and gain characteristics as compared to the resonant behaviour of the input impedance. The most significant feature of this technique is that there is no need to find any analytical description of the antenna and generator, and it only utilizes directly real frequency generator and load data over the prescribed frequency band. Furthermore, it is not necessary to invent an analytic form of the system transfer function to assume a matching network topology in advance. In this paper, the transmission line model is used to investigate the rectangular microstrip antenna, and based on the Fano's bandwidth-enlargement theory, the SRFT is introduced to design the matching networks of microstrip antennas in order to obtain a constant gain over the frequency band of interest. Two representative microstrip antnnas with different structure are fabricated and tested. From these procedures, it is obtained that the proposed impedance matching networks of microstrip antenna improve the impedance bandwidth nearly three times compared to the antenna without them.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.7
• /
• pp.1240-1246
• /
• 2000

The finite-difference time-domain (FDTD) method is applied to analyze a single step microstrip discontinuity in the substrate, and an equivalent circuit model comprised of two inductors and a capacitor has been developed using the numerical results. The microstrip discontinuity newly introduced in this paper has a thickness change of the substrate in the longitudinal direction with a uniform strip width. The discontinuity can be applied to the feeding circuit design for the patch antennas and interconnections between microwave circuit modules. The simulation results are compared with those computed by HFSS, and two results showed a good agreement. An equivalent circuit developed from the FDTD results, which is accurate within 2.4% in magnitudes of $S_{11}$ and $S_{21}$,can be applied for the computer-aided design of microwave circuits.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2006.05a
• /
• pp.637-640
• /
• 2006

In this paper, a microstrip antenna with a small loop consisting of the left and right parallel plate to load capacitor is proposed. It is obtained the improved small size than the antenna of the transformed Uh and the antenna of the left and right parallel plate to load capacitor on QMSA. Equivalent circuit of transmission line model is designed to find more accurate resonant frequency. Also, the designed and fabricated antenna can receive both vertically and horizontally polarized waves to operating frequency of 1.5GHz. Therefore proposed antenna is available as a small antenna for wireless communication and will be quite useful for indoor communication

• Journal of the Korean Magnetics Society
• /
• v.17 no.6
• /
• pp.242-245
• /
• 2007

Conduction noise attenuation by composite sheets of high magnetic and dielectric loss has been analyzed by using electromagnetic field simulator which employs finite element method. The simulation model consists of microstrip line with planar input/output ports and noise absorbers (magnetic composite sheets containing iron flake particles as absorbent fillers). Reflection and transmission parameters $(S_{11}\;and\;S_{21})$ and power loss are calculated as a function of frequency with variation of sheet size and thickness. The simulated value is in good agreement with measured one and it is demonstrated that the proposed simulation technique can be effectively used in the design and characterization of noise absorbing materials in the RF transmission lines.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.13 no.2
• /
• pp.182-191
• /
• 1988

A log periodic microstrip array antenna using direct coupling feeder is designed at the frequency 7.2-12.4GHz. Transmission line analysis method was used for the design of each antenna element in consideration of the effects of dielectric and conductor loss and the discontinuity, also the optimized feeding points were obtained for the impedance matching between a main transmission line and each antenna element. It is shown that the measured VSWR was less that 2.4 at the frequency 7.2-12.4GHz, and 53% bandwidth was achived.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.3
• /
• pp.75-79
• /
• 2008

Transmission line characteristics in microstrip line is used to in this paper. 5-microstrip lines composed of various spacing between them suggests characteristics of a diplexer in simulation. By applying the simiulation results, the diplexer realized shows better results of flat responses in bandpass characteristics and bandstop characteristics around 15 dB than symmetric spacing one.