• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.977-980
• /
• 2011

In this paper, explain to development of low pressure axial compressor performance test rig in KARI. Performance test rig consist of a entrance section, rotor, stator, shaft, rig housing, bearing housing and exit section. Test rig design structural optimization to rotor dynamics analysis of the simplified rotor-shaft assembly and flow analysis of entrance/exit section.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.373-376
• /
• 2009

A full rig combustor test and altitude ignition test were carried out for radial-annular combustor of micro turbojet engine. 11.2% total pressure loss and 99.85% of combustion efficiency were measured at design point of engine under sea level standard condition and $2{\sim}6$ of air excess ratio for ignition envelope was achieved on engine starting regime. Finally, A 30,000 ft high altitude ignition test was also performed and finally we found out that the developed radial-annular combustor is appropriate to micro turbojet engine.

• Aerospace Engineering and Technology
• /
• v.8 no.1
• /
• pp.98-107
• /
• 2009

Vibration analysis of a turbo compressor test rig was carried out in order to investigate the vibrational characteristics of the compressor facility in KARI before conducting the compressor performance test of 5MW-class gas turbine engine for generation. The overall compressor test facility consists largely of inlet and exit ducts, a test section and a driving part. Vibration was measured with accelerometers at the test section and the driving part, especially at a main housing, a collector, a bearing carrier, a torquemeter, a gearbox, and an electric motor. Gap sensors are also installed to measure the rotordynamic characteristics of compressor shaft.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.11a
• /
• pp.149-152
• /
• 2008

A slinger combustor which can be applied to micro turbojet engine has been developed with the combustor rig test. A rotating fuel injector with high speed rpm was designed, manufactured and tested to apply into slinger combustor through spray test and adequate droplet size and spray distribution were achieved. The CFD was used to analyze internal flow of the combustor. We found out that the combustor shows 11.2% of pressure loss and 99.8% of combustion efficiency at full combustor rig test.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.825-828
• /
• 2010

APU for aircraft is operated under severe condition as high altitude and low temperature, and demand high reliability in flight. This study is to be verified of the ignition and the combustion stability of APU under the harsh conditions. The basic data obtained in combustion rig test were directly applied to the altitude test with a engine. That start logic was obtained in ground development test. The results of altitude test show that air swirl injector has good operation and ignition performance at 20kft, hot/cold($-40^{\circ}C$) day.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.12
• /
• pp.1573-1579
• /
• 2013

To test the performance of nuclear fuels, coolant needs to be circulated through the test rig installed in the test loop. Because the pressure and temperature of the coolant is 15.5 MPa and $300^{\circ}C$ respectively, coolant sealing is one of the most important processes in fabricating a nuclear fuel test rig. In particular, 15 instrumentation cables installed in a test rig pass through the pressure boundary, and brazing is generally applied as a sealing method. In this study, an induction brazing system has been developed using a high frequency induction heater including a vacuum chamber. For application in the nuclear field, BNi2 should be used as a paste, and optimal process variables for Ni brazing have been found by several case studies. The performance and soundness of the brazed components has been verified by a tensile test, cross section test, and sealing performance test.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.8
• /
• pp.111-121
• /
• 2005

A 100kW class gas turbine combustor was developed and tested for PPU(Primary Power Unit) of ground vehicle. The combustor which employed annular-reverse type and pressure swirl atomizer was designed through 1-D analysis, 3-D thermal flow analysis and combustor performance was experimentally investigated on the combustor test rig. The test result was satisfactory. The developed combustor was also tested for environmental and endurance specification under engine adopted conditions and the application of a state-of-the-art gas turbine combustor to ground vehicle PPU turned out to be successful.

• 한국연소학회:학술대회논문집
• /
• 2015.12a
• /
• pp.269-269
• /
• 2015

두산중공업이 국책과제로 개발 중인 한국형 대형 가스터빈의 연소기 개발현황 및 결과에 대해 기술하였다. 압력손실 5%, 연소효율 99.9%, 15ppm NOx 배출 성능을 가지는 14개의 캔형 연소기로 구성되었으며, 40% turn down ratio 운전, WI ${\pm}7%$의 fuel flexibility 성능 및 dual fuel 적용 가능한 운전 성능 목표를 가진다. 이를 위해 Dry Low NOx 형 연소기를 개발, 단일 노즐 연소시험을 수행 중이며, 2016년 상반기 중 상압연소리그시험을 거쳐 그 성능을 검증하고자 한다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.2
• /
• pp.68-74
• /
• 2006

An experimental study was carried out to investigate the combustion characteristics of the slinger combustor. A combustion test rig was manufactured and installed in KARI combustor test facility. From the ignition test results, we found that there were two major factors influencing the ignition limits; by increasing the rotational speed and the air mass flow rate, a better ignition performance was attained. From the combustion test results, we obtained 99.6% combustion efficiency, 15% pattern factor, and 3% profile factor. The results in this work indicate that the ignition and combustion characteristics of a slinger combustor are markedly different from those of a conventional annular combustor.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.6
• /
• pp.51-58
• /
• 2019

In this study, a set of performance tests on 3D-printed combustor components were carried out to investigate the performance of 3D-printed component and its feasibility for micro gas turbine engines. The test were conducted for four different equivalence ratios under two different engine operating conditions. The measurement results show that the tested combustor had a low total pressure loss coefficient and a uniform exit temperature distribution. However, the combustion efficiency values are less than 93.5% owing to the large amount of UHC and CO, which is considerably lower than a typical gas turbine engine combustor. The performance data obtained from the tests will be used for combustor performance improvements using 3D-printing technology.