• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.11
• /
• pp.17-23
• /
• 2004

The implementation and design of the wideband IFIU using aperture open loop resonator and reversed phase technique to reduce the local oscillator leakage signal was represented in this paper. The local oscillator leakage signal is generated in stage of frequency conversion, especially in frequency conversion of fully digital modulation signal close to DC signal. The leakage signal and spurious signals, which have effects on adjacent channel or in-band channel as interference signals, were reduced below -60 dBc for 45 Mbps and 155 Mbps IF interface units. The group delay for both IFIUs shows low ripple characteristics of 15 ns and 8 ns, respectively. Also, the amplitude ripple characteristic in 150 MHz bandwidth with L-band center frequency satisfies the required specification of 2 dB. The implemented IFIU provides the required specifications for wideband satellite communication system.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.6
• /
• pp.505-516
• /
• 2011

The concept of the IGC(Integrated Guidance and Control) has been introduced to overcome the performance limit of the SGC(Separated Guidance and Control) loop. A new type of IGC with impact angle constraint has been proposed in this paper. Angle of attack, pitch angle rate, pitch angle and line of sight angle are considered as state variables. A controllability analysis and equilibrium point analysis have been carried out to investigate the control characteristic of the prposed IGC. The LQR(Linear Quadratic Regulator) has been adopted for the control law and detailed explanations about the adoption has been provided. The performance comparison between the IGC and the SGC has been carried out. The result of numerical simulations shows that the IGC guarantees better guidance performance than the SGC when the agile maneuver is needed for a specific guidance geometry.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.17 no.1
• /
• pp.116-123
• /
• 2003

In this paper, interleaved boost converter is applied as a pre-regulator in switched mode power supply. The pre-regulator plays a role to improve power factor. Interleaved Boost Power Factor Corrector(IBPFC) can reduce input current ripple as a single voltage control loop only without inner current loop, because input current is divided each 50% by two switching devices. Each converter cell is also operated in discontinuous current mode and inductor current of each converter is discontinuous. Total input current which is composed by each converter cell is continuous current. Thus, IBPFC is able to improve input current ripple. IBPFC operating in discontinuous current mode can be classified as six modes from switching state and be carried out state space averaging small signal modeling. A control transfer function is obtained according to the modeling. Single voltage control loop is also constructed by the control transfer function. From experimental result, improvement of power factor and input current ripple are verified.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.12 no.1
• /
• pp.58-65
• /
• 2013

It's introduced a BLA(Branch Loop Antenna) that is modified from conventional loop, and verified antenna performances for applying to mobile handset. Branch elements are added to a rectangular loop, and low resonance is obtained by the length of the branch line. When resonance frequency of a single loop is 2.5GHz, BLA had near 900 MHz under the same antenna size. Multiple resonances are established by the locations of branch connection and their lengths. By the implementation and measurement for the dual band BLA, it's showed 75MHz -10dB bandwidth and -3.03~-1.46dBi average gains with 49.73~71.39% efficiencies at GSM900 band, and 90MHz -6dB bandwidth and -8.14~-2.17dBi average gains with 15.34~60.62% efficiencies at DCS1900 band. And H-plane radiation patterns were omni-directional. These performances are good for the mobile handset antenna.

• Information and Communications Magazine
• /
• v.31 no.6
• /
• pp.69-74
• /
• 2014

기후변화에 적극 대처하여 지속적이고 안정적인 용수 공급을 위해 기존의 용수 생산 공급망에 정보통신 기술(Information & Communication Technologies, ICT)을 접목한 지능형 물관리를 위해 '스마트 워터 그리드(smart water grid)'를 구축하고자 하는 다양한 노력이 최근 들어 지속되고 있다. 즉, 스마트 워터 그리드는 기존의 수자원 관리 시스템의 한계를 극복하기 위해 첨단 정보통신기술을 이용하는 고효율의 차세대 인프라 시스템으로 다양한 수원을 활용하고 물을 효율적으로 배분 관리 운송하여 수자원의 불균형을 해소하고, 첨단 센서 네트워크를 이용해 실시간으로 수자원망의 안정성을 모니터링하는 등 용수관리 전분야에 걸쳐 양방향 실시간으로 용수정보를 감시 대응하여 용수관리와 에너지 효율의 최적화된 메가시티(mega-city)에 적합한 지능형 물관리가 가능할 것으로 예상되는 시스템이다. 따라서 본 고에서는 선진화된 상수도시스템 운영을 위해서는 현장설비의 관측값을 감시하고 제어하는 시스템에서, 운영 방식이 변경될 때마다 운영 변수간의 인과관계를 분석하고 예측할 수 있는 시뮬레이션 기능이 탑재된 상수도 운영시스템이 요구되고 있는 실정에서 용수공급 시스템의 운영 상황을 모의할 수 있는 모형 개발 및 용수공급시스템의 운영룰 모의 및 운영의사결정에 적용할 수 있는 다중수원 워터루프 시스템과 운영관리할 수 있는 S/W를 개발 내용을 소개하였다.

• Proceedings of the KIEE Conference
• /
• 2006.04b
• /
• pp.223-225
• /
• 2006

본 논문에서는 매입형 영구자석 동기전동기(IPMSM)의 속도추정을 위한 새로운 센서리스 알고리즘을 제안한다. 매입형 영구자석 동기 전동기의 기본 전압 방정식을 이용하여 회전자의 자속을 추정하고, 위상고정루프(PLL)를 사용하여 회전자의 위치와 속도를 추정하는 방법으로 센서리스 알고리즘을 구성하였다. Matlab SIMULINK를 이용한 시뮬레이션과 실험을 통하여 제안된 알고리즘을 검증하였다.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2010.11a
• /
• pp.200-201
• /
• 2010

블록 기반의 적응적 루프 필터(BALF : Block Adaptive Loop Filter)는 압축 성능에 있어서 상당히 높은 효율을 보이는 기술 중 하나이다. BALF는 복원된 영상을 원본 영상에 최대한 유사하게 만드는 Weiner 필터계수와 해당 필터가 적용될 영역에 대한 정보를 복원된 영상에 적용함으로써 화질을 높일 수 있다. 그러나 BALF는 단위블록 전체에 대해 하나의 필터를 생성하여 적용하는 방법으로, 블록 내부에서 구분되는 신호적 특성을 따로 분류하지 않는다. 그러므로 BALF는 높은 부호화 성능을 보이는 반면, 높은 복호화 복잡도를 요구한다는 단점이 있다. 본 논문에서는 필터가 적용될 블록을 내부와 경계 영역으로 나누어 경계 영역을 위한 필터를 구분하여 생성하는 루프필터를 제안한다. 제안하는 알고리즘은 기존의 BALF에 비해 부호화 성능이 저하되지만, 필터를 적용할 영역을 선택 가능하게 함으로써 복호화 복잡도를 조절할 수 있도록 하였다. 제안한 방법의 실험결과, 기존의 방법인 BALF에 대하여 블록의 경계 영역 필터를 사용할 경우, 약 3.77%의 부호화 성능 저하에 대하여 약 33.76%의 필터링 속도 향상을 보였다.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.5
• /
• pp.589-595
• /
• 2010

This paper presents a reliability-based shape optimization (RBSO) using the evolutionary structural optimization (ESO). An actual design involves uncertain conditions such as material property, operational load, poisson's ratio and dimensional variation. The deterministic optimization (DO) is obtained without considering of uncertainties related to the uncertainty parameters. However, the RBSO can consider the uncertainty variables because it has the probabilistic constraints. In order to determine whether the probabilistic constraint is satisfied or not, simulation techniques and approximation methods are developed. In this paper, the reliability-based shape design optimization method is proposed by utilization the reliability index approach (RIA), performance measure approach (PMA), single-loop single-vector (SLSV), adaptive-loop (ADL) are adopted to evaluate the probabilistic constraint. In order to apply the ESO method to the RBSO, a sensitivity number is defined as the change of strain energy in the displacement constraint. Numerical examples are presented to compare the DO with the RBSO. The results of design example show that the RBSO model is more reliable than deterministic optimization.

• Journal of Advanced Navigation Technology
• /
• v.7 no.2
• /
• pp.108-117
• /
• 2003

In this paper, two types of radar vehicle detectors compatible with currently being used ILD(Inductive Loop Detector) without any modification has been developed. With these vehicle detectors based on FMCW altimeter and Doppler speedometer techniques at 24 GHz, the length and speed of a vehicle can be detected. For signal processing part, we have used DAQ board and programmed with LabView. For compatibility with traffic information network connected with existing ILD's, traffic information has been sent to VDS by using RS-232C standard interface. This development has improved approximately 10% in accuracy in terms of the speed and length information compared with that of the installed ILD in the test field.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.4
• /
• pp.469-475
• /
• 2010

The objective of this study is to integrate reliability analysis into shape optimization problem using the evolutionary structural optimization (ESO) in the application example. Reliability-based shape optimization is formulated as volume minimization problem with probabilistic stress constraint under minimization max. von Mises stress and allow stress. Young's modulus, external load and thickness are considered as uncertain variables. In order to compute reliability index, four methods, i.e., reliability index approach (RIA), performance measure approach (PMA), single-loop singlevector (SLSV) and adaptive-loop (ADL), are used. Reliability-based shape optimization design process is conducted to obtain optimal shape satisfying max. von Mises stress and reliability index constraints with the above four methods, and then each result is compared with respect to numerical stability and computing time.