• Transactions of Materials Processing
• /
• v.25 no.2
• /
• pp.102-108
• /
• 2016

The aim of the current study was to develop an advanced prediction model for the slab width spread during hot rough rolling. Rough rolling consists of both vertical rolling using a set of profiled edger rolls and horizontal rolling using a set of plain work rolls. FE-simulations were performed to investigate the influences of process variables such as initial slab width, initial thickness, sizing draft, edger roll draft and work roll draft on the final slab width variation. From a statistical analysis of the simulation results, an advanced model, which can predict the slab width spread during the edger rolling and horizontal rolling, was developed. The experimental hot rolling trials showed that the newly developed model provided fairly accurate predictions on the slab width spread during hot rough rolling process using a profiled edger rolls.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.2
• /
• pp.58-65
• /
• 1997

Work rolls used in cold rolling mills must have outstanding wear resistance and very little plastic defor- mation. Thus, these rolls require a higher surface hardness and harding to a greater depth. To meet these requirements, the rolls, in general, have basic chemical composition of 0.7 to 1.0% carbon and 1.0 to 5.0% Cr(chromium), plus a small amounts of special elements, and are subjected to intensive water quenching and tempering at low temperature to provide a surface hardness of over 90 shore. This test results are as follows. Deflection and fracture load of 5% Cr material are than those of 3% Cr material and show flat curve from surface to subsurface. It will be clear that 5% Cr work roll has a superior resisti- bility against wear and abrasion comparing with 3% Cr work roll. The improvement of wear and abrasion in 5% Cr work roll will be achieved by the large amount of wpheroidal carbide. In grindability and polish, 5% Cr work roll will be a little inferior comparing with 3% Cr work roll.

• The Korean Journal of Petroleum Geology
• /
• v.5 no.1_2 s.6
• /
• pp.1-8
• /
• 1997

Seismic stratigraphic analysis of the high resolution profiles obtained from the southeastern shelf of Korea divided the deposits into 4 sequences; 1) sequence D, 2) sequence C, 3) sequence B and 4) sequence A (Holocene sediments). Sequence D was deposited in shallow-water environment at west of the Yangsan Fault as the basin subsided. On the other hand, the eastern part was formed at the slope front. Landward part of the slope-front fill sediments were eroded and redeposited nearby slope due to the syndepositional tilting of the basin. This tilting probably resulted from the continuous closing of the Ulleung Basin. Sequence C is made of stacked successions of the lowstand fluvial sediments, transgressive sediments and marine highstand sediments derived from the paleo-river in the western part of the Yangsan Fault. Sequence C in the eastern part of the Yanshan Fault was formed at the shelf break. Progradation of the lowstand sediments resulted in broadening of the shelf. Sequence C in the eastern part was also tilted but the tilting was weaker than in Sequence D. During the formation of sequence B the tilting stopped and the point source instead of the line source started in both sides of the Yangsan Fault. Sequence B was composed of the highstand systems tract partially preserved around the Yokji island, lowstand systems tract mainly preserved in the Korea Trough and transgressive systems tract. After the stop of the tilting, the force of compression due to the closing of the Ulleung Basin may be released by the strike-slip faults instead of tilting.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.9
• /
• pp.849-855
• /
• 2010

This paper investigated the roll lock-in phenomena of a canard-controlled missile with freely spinning tailfins by applying Falanga's roll-rate equation. To confirm and validate the accuracy of the results of the roll-rate and roll lock-in prediction for freely spinning tailfins, the results were compared with Blair's wind tunnel test data. For calculation of the roll-rate of freely spinning tailfins, rolling moment coefficients of the tailfins were obtained from the wind tunnel test data and roll-damping coefficients were calculated by missile DATCOM. The roll-rate and roll lock-in of the freely spinning tailfins were calculated by applying these values to the roll-rate equation for freely spinning tailfins. The calculation results showed good agreement with the wind tunnel test data, and the roll lock-in could be anticipated as well.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.10
• /
• pp.1443-1453
• /
• 2010

We simulated the roughing train of the rod mill of SEAH BESTEEL Inc. using finite element method to inhibit surface cracks initiation on workpiece. We designed 2nd pass (square roll) and applied to this roll in the roughing train of the rod mill. Also, we proposed new pass schedule, which changed roll gap of 3rd and 4th groove by using finite element method. We used shear damage model, which is dependent on shear stress ratio and compared the number of damaged elements on workpiece. A damaged element means surface crack. Consequently, after 2nd pass (square roll) is changed, the error rate decreased by 1.43% when compare to that of the old groove. And the number of damaged elements in the new pass schedule decreased by 37.6%, which is less than present pass schedule.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.27 no.1
• /
• pp.33-38
• /
• 2019

This study refers to the deodorization of DDM Environmental Resource Center, which is operating abnormally in the food waste public-resource facilities that are operating nationwide, in accordance with the initial operating conditions. Issues concerning the abnormal deodorization facilities of DDM Environment Resource Center were the deodorization of composting facilities, indoor air quality problems, and overall deodorization of facilities, especially the phenomenon of stopping while operating the RTO and the phenomenon of poor spray in the wet scrubber etc. As an alternative and improvement method for converting such abnormal operation facilities into normal operation facilities, It is proposed to remove the front filter of the upper part of the fermentation tank, and to install scrubbers, air and water separator, and roll filters for dust removal etc.

• 한국벤처창업학회:학술대회논문집
• /
• 2023.04a
• /
• pp.93-99
• /
• 2023

경기 침체와 더불어 고용 불안, 그에 따른 사회의 혼란 속에서 국가의 성장 동력의 대안 중 하나로 창업 활성화의 요구가 높아지고 있다. 우리나라를 비롯한 많은 국가에서 창업 활성화를 중장기 목표로 설정하고 다방면으로 노력하고 있다. 이에 따라 창업의도를 높일 수 있는 요인에 대한 연구가 진행되어 왔고, 특히 자기효능감과 창업기회인식 등의 개인적 역량 요소가 창업의도를 높인다는 연구 결과들이 지속적으로 제시되고 있다. 이러한 창업의도를 높일 수 있는 자기효능감, 창업기회인식을 고취시키기 위해 학계의 연구활동 뿐 아니라 정부의 정책적 접근 또한 활발하게 이루어지고 있다. 창업교육 활성화부터 사회적 환경 조성을 위한 창업 롤모델 활용, 미디어를 통한 창업 활동 홍보 등 긍정적인 창업 경험을 공유하도록 하기 위한 연구 역시 계속되고 있다. 그러나 개인적 역량 요소와 사회적 환경 조성 외에 문화적 특성이 창업의도에 영향을 미치는지에 대한 연구는 부족하였다. 본 연구는 문화적 특성이 창업의도를 높일 수 있는 요인으로 개인적 역량 요소와 사회적 환경 조성과 함께 의미가 있을 것이라는 물음에서 시작하였다. 가설 검증을 위하여 SPSS 26버전을 활용하여 로지스틱 회귀분석 하였고 GEM KOREA의 2017년 데이터를 분석하였으며, 자기효능감과 창업기회인식은 창업의도에 긍정적인 영향을 미친다는 기존 연구 동일한 결과가 나왔다. 본 연구의 특징은 문화적 특성을 집단주의와 관계주의로 구분하여 자기효능감, 창업기회인식과 창업의도에 영향을 미치는 과정에서의 조절효과를 검증하였다는 것이다. 문화적 특성 중 집단주의 특성은 유의하지 않았으나 관계주의 특성이 유의하여 조절효과를 가진다는 결과를 얻어냈다. 이는 국가에 새로운 성장 동력이 필요한 상황에서 창업의도가 없거나 낮은 개인들도 관계주의 특성을 활용하여 창업의도를 높일 수 있다는 연구 결론으로 이어진다. 지금까지 알려진 바와 달리 한국은 집단주의 보다 관계주의가 강하기 때문에 관계주의 문화 특성을 고려하여 선배 창업가 또는 로컬 창업가들과의 관계를 만들고 유지할 수 있도록 하는 등의 정책을 수립할 필요가 있다는 것을 시사한다. 하지만 이미 설계된 GEM 데이터를 활용하였다는 점, 문화적 특성이 각기 다른 국가들과의 비교연구가 필요하다는 점 등은 본 연구의 한계라고 할 수 있다.

• Journal of Korean Society of Steel Construction
• /
• v.16 no.1 s.68
• /
• pp.33-42
• /
• 2004

Making use of SN steel in the building structure should be a prerequisite to adopt the design strength of said steel. As a preceding study, the material properties of STKN400B/490B tubes and SPAP235/325 and SPAR295 square pipes manufactured using SN400B/490B plates were evaluated. Compared with the yield and ultimate strengths of SN400B/490B plates, those of STKN400B/490B tubes increase. Nonetheless, the yield and ultimate strengths of STKN400B/490B tubes satisfied the design codes of STKN400B/490B tubes even though the tubes were fabricated via roll bending or press forming. On the other hand, the yield and ultimate strengths at the edges of SPAP235/325 square pipes did not satisfy the design codes based on the values at the sides. The maximum tensile and compressive residual stresses at the SN490B tube were equal to and 40% of the yield strength of the SN490B plate, respectively, In the case of the SPAP325 square pipe, both the maximum tensile and compressive residual stresses were 80% of the yield strength of the SN490B plate. The axial compressive loaded column test results snowed that the buckling strengths were not very different regardless of the mode of fabrication of STKN490B tunes. i.e., through roll bending or press forming. On the other hand, the buckling strength of the SPAP325 square pipe was higher than that of the built-up square pipe.

• The Korean Journal of Petroleum Geology
• /
• v.5 no.1_2 s.6
• /
• pp.9-15
• /
• 1997

The study area is located in the Central Bransfield Basin, Antarctica. To analyze the morphology of seafloor, structure of basement, and seismic stratigraphy of the sedimentary layers, we have acquired, processed, and interpreted the multi-channel seismic data. The northwest-southeastern back-arc extension dramatically changes seafloor morphology, volcanic and fault distribution, and basin structure along the spreading ridges. The northern continental shelf shows a narrow, steep topography. In contrast, the continental shelf or slope in the south, which is connected to the Antarctic Peninsula, has a gentle gradient. Volcanic activities resulted in the formation of large volcanos and basement highs near the spreading center, and small-scale volcanic diapirs on the shelf. A very long, continuous normal fault characterizes the northern shelf, whereas several basinward synthetic faults probably detach into the master fault in the south. Four transfer faults, the northwest-southeastern deep-parallel structures, controlled the complex distributions of the volcanos, normal faults, depocenters, and possibly hydrocarbon provinces in the study area. They have also deformed the basement structure and depositional pattern. Even though the Bransfield Basin was believed to be formed in the Late Cenozoic (about 4 Ma), the hydrocarbon potential may be very high due to thick sediment accumulation, high organic contents, high heat flow resulted from the active tectonics, and adequate traps.

• Korean Journal of Breeding Science
• /
• v.40 no.1
• /
• pp.31-38
• /
• 2008

This experiment was carried out to improve the anther culture efficiency of barley (Hordeum vulgare L.). Callus induction rates from anther cultures of the five domestic naked barley and four unhulled varieties ranged from 0 to 5.6%, and plant regeneration rate to callus was 30.4% in the donor plants grown in a greenhouse during winter, among which the green plant regeneration rates ranged from 0 to 4.4%. Plant regeneration rate was 30.4% in the donor plants grown in a greenhouse during winter, whereas 21.3% in the normal field condition in spring. In addition, callus induction rates were 19.2% in plants grown in a normal field and 7.2% in drought-stressed condition, respectively. Being Considered the anther culture efficiency affected by the sampling time, the optimum sampling stage of anthers was 3~4 days before heading when the length between the 1st and 2nd auricles reaches 5 to 10 cm and at the uninucleate of pollen which the tip of the 2nd auricle aligns with the middle of panicle in the leaf sheath. Best callus induction rates came from the anthers stored at $4^{\circ}C$ for 3 weeks in a 10 to 15 cm diameter polyethylene bag with 5 to 10 panicles and Duwonchapssalbori and Saessalbori showed the higher induction rate of 4.8% and 1.7%, respectively.