• Journal of the Korean Society of Propulsion Engineers
• /
• v.7 no.4
• /
• pp.19-26
• /
• 2003

In this paper, the result of the conceptual study of a tipjet driven propulsion system is presented. The concept of a tipjet driven propulsion system is to employ tipjet as power source to drive a rotor Because the vehicle is supposed to takeoff and land vertically, a rotor system, which has tipjet nozzles, is adopted to fly like a helicopter. Exhaust gas, which is generated by an engine, Passes through an internal duct system and divided into four blade ducts. The design code is consists of two parts, engine model and internal duct model. Inside a rotating duct, compressible flow is affected by two additional force terms, centrifugal force and coriolis force and they govern the performance in rotary mode, The intention of this paper is to address the issues associated with sizing and optimizing configurations of a tipjet driven propulsion system especially in rotary wing mode.

• Aerospace Engineering and Technology
• /
• v.5 no.2
• /
• pp.240-247
• /
• 2006

Tilt rotor aircraft is a multi-configuration airplane which has three independent flight modes; helicopter, conversion, and aiplane. The control surface mixer resign is reqctired to generate and distribute efficient control forces and moments in each flight mode. In the conversion mode, the thrust vector is changed from helicopter mode to airplane, therefore the thrust vector makes undesired forces and moments which affect on pitch, roll and yaw dynamics. This paper describes the design results of control surface mixer design which minimize the undesired forces and moments due to nacelles tilting angle change for 4O% scaled model.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.3
• /
• pp.287-291
• /
• 2015

This study investigates the result of thermal stress analysis on disk rotor by classes at bike brake. In the analysis result of thermal deformation at the steady state, maximum deformations at models 1, 2 and 3 are 0.14347mm, 0.15823mm and 0.16028mm respectively. The deformation becomes larger as the field goes on from the center to the outside at disk rotor. As there are models 1, 2 and 3 in the order of maximum deformation, model 1 has safest among three models. In the analysis result of thermal stress at steady and transient states, there are models 1, 2 and 3 in the order of maximum stress. Model 1 becomes most excellent on strength and safety among three models. By using the analysis result of disk rotor model at bike disk, it is possible to design the model applied practically at the safe driving of bike.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.1
• /
• pp.51-56
• /
• 2013

This paper is the experimental study to investigate the noise sources location in order to reduce the noise level of line flow fan for the air conditioner in the subway car. The noise of line flow fan is caused by various factors such as the turbulence by air flow, random noise, noise of blade passing frequence(681Hz) and noise due to structural vibration of rotor unbalance(28.4Hz) by motor revolution. By performing the noise reduction on each sound source, the noise level is decreased as much as 5.7dB(A) through the controls of housing guide angle and distance, the configuration changes of flow passage shape and rotor balancing.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.117-122
• /
• 2012

A blisk with rotor shroud is usually adopted in LRE turbine to maximize its performance. However it experiences severe thermal load and resulting damage during engine stating and stop. Shroud splitting is devised to relieve thermal stress on the turbine rotor. Structural analysis confirmed the reduction of plastic strain at the blade hub and tip. However, split gap at the rotor shroud entails additional tip leakage and results performance degradation. In order to assess the effect of shroud split on the turbine performance, tests have been performed for various settings of shroud split. For the maximum number of shroud splitting, measured efficiency reduction ratio was 2.65% to the value of original shape rotor.

• Journal of the Society of Naval Architects of Korea
• /
• v.60 no.5
• /
• pp.351-357
• /
• 2023

In this study, we devised methods to enhance the efficiency of rotor sails which have been applied as one of the energy saving devices of ships. The idea of the study originated from the notion that installing protrusions or increasing the surface roughness on the smooth surface of the rotor sail could delay the separation of the incoming wind flow and consequently increase the lift force. Five cylinder models were considered and tested in an open-type wind tunnel at Chungnam National University. A smooth surface cylinder exhibits the highest lift-to-drag ratio at a specific Reynolds number, and as the Reynolds number increases this value decreases sharply. The variation in this typical Magnus force can be significantly improved by altering the surface shape and roughness of the rotor sail. It has been observed that increasing the surface roughness improves the lift characteristics, resulting in increased efficiency. Furthermore, it revealed that the reverse Magnus effect which may occur during actual operation in the low spin ratio region can be significantly enhanced.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.5
• /
• pp.390-397
• /
• 2014

BO-105 helicopter applies hingeless rotor hub system and blade root uses a flexure of hingeless rotor hub system. So bending stiffness reinforcement for flexure was conducted for preparation of whirl tower test using BO-105 blade. Bending moment of flexure area was calculated with FE modeling of section shape for stiffness reinforcement of flexure and thickness of composite material for reinforcement was chosen. Flexure bending stiffness reinforcement was conducted and bending stiffness measurement test was performed before and after bending stiffness reinforcement. And the test data are compared with analysis results.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.59-59
• /
• 2017

무인 헬리콥터의 양력을 개선하기 위한 익형 설계 단계로서 두꺼운 익형(V1505A)과 얇고 처진 익형(V2008B)의 기본 두 익형의 특성을 예측하는데 있어 회전하는 블레이드의 현실적 조건을 반영한 3D 모델을 마련하고 성능을 예측하였다. Fluent를 이용한 400 mm 선형모델의 시뮬레이션에서는 V1505A 익형은 높은 받음각에서 안정적인 특성을 보인 반면 V2008B는 비교적 높은 동력효율 특성을 보였으나, 높은 받음각에서는 실속 이후 양력이 급락하는 특성을 나타낸다. 형성된 노드 수는 약 870,000개로 하였다. 시위길이 135 mm인 익형 V2008B의 형상은 ANSYS (Fluent v16.2)를 이용해 반경(길이) 1,502 (1,380) mm 의 로터 블레이드를 구성하였다. 충분하지 않은 유동장이 익형 표면에서의 유동의 영향에 영향을 주지 않도록 직경 20 m의 원방경계(far field)를 형성하였다. 사용된 매쉬의 형태는 정사면체 형태로 로터 표면으로부터의 첫 번째 두께 높이는 0.001 m이고 10개의 층으로 형성하였다. 정지 비행하는 헬리콥터의 상태를 가정하여 회전좌표계를 이용하여 정상상태의 유동을 해석하고 사용된 난류모델은 넓은 영역에서의 유동을 고려하여 Realizable $k-{\varepsilon}$ 모델을 사용하였다. 내측그립 받음각 $6{\sim}22^{\circ}$에 대하여 현실적인 회전속도를 연동하여 600~1000 rpm을 적용하였다. 반복수(iteration)는 2000으로 하여 잔차값(residual)이 충분히 수렴하도록 하였다. 전체적으로 실제 헬리콥터가 발휘하는 양력보다는 낮은 수치로 예측되었으며 모델 및 해석 조건에 대한 검토가 필요해 보인다. 양력 값은 받음각 $10^{\circ}$에서 자중(약 68 kgf)을 극복하였고 받음각 $12^{\circ}$에 유상하중 20 kgf을 발휘하며 888 N의 양력을 보였다, 이어 받음각 $22^{\circ}$에서 실속 현상이 발생하였다. 받음각이 증가함에 따라 항력 역시 증가하였으며 받음각 $12^{\circ}$에서 121 N이었고 실속에 이르며 항력은 갑자기 증가할 것으로 예측된다. 본 연구는 변이 익형 개발의 선행 단계로 기본 익형에 대한 공력특성을 CFD 시뮬레이션을 통하여 예측하였다. 예측 값은 현실적 실험방법을 통하여 검증이 되어야 하며 이후 변이익형에 대한 예측과 설계가 가능하다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.6
• /
• pp.8-14
• /
• 2017

Gearboxes for power transmission of a rotorcraft transfer power generated by an engine to the fan and the pusher for up, down and forward flight. The gearboxes are divided into the main gearbox and the sub-gearbox. The main goal of the gearbox design is to design the weight as light as possible within a range that satisfies all given requirements (transmission power, mounting space, etc.). In particular, the initial conceptual design is very important to reduce the weight of the gearbox, since the weight can vary greatly depending on the system configuration, even if it has the same function. In this study, various conceptual designs of the gearbox according to the installation position of the engine were presented. Also, the element parts such as gears and bearings in each concept design were designed by sizing for their life, and the estimated weights of the conceptual system configuration were compared.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.183.2-183.2
• /
• 2010

본 개발에서의 해상용 풍력발전기는 크게 허브와 블레이드를 합한 상부 구조물, 전기 발전기와 연결 조인트의 중간구조물, 각종 제어 장치가 들어있는 제어박스로 나누어진다. 상부 구조물은 Circular Hub 타입의 Darrieus 형상으로 양력(lift)을 이용한 회전력이 발생하며, Circular Hub 타입은 기존의 허브와 블레이드를 연결하여주는 암(arm)에 의해 유발되는 항력토크를 최소화 하기 위한 신개념 형상설계가 이루어 졌으며, 저속에서 우수한 회전특성을 가진다. 이는 바람을 받아 기계적 에너지로 전환 하는 역할을 하며, 풍력발전기의 성능에 직접적인 영향을 미친다. 중간구조물의 전기발전기는, 상부에서 발생된 기계적 에너지를 이용하여 전기적 에너지로 전환 하는 역할을 수행한다. 이렇게 전환된 전기적 에너지는 하부의 제어박스를 거쳐서 해상용 부이(buoy)의 하단에 위치한 베터리 뱅크로 전달, 저장되어 부이에서 쓰이는 전력을 충당하게 된다. 한편 본 개발은 풍력발전기의 공력하중 해석과 로터블레이드의 설계, 풍력발전기의 구조, 진동해석, MPPT 제어컨트롤러와 Breaking controller, 풍동 및 차량시험을 통한 성능평가 및 분석 등의 순으로 개발을 수행하였다.