• Membrane Journal
• /
• v.22 no.1
• /
• pp.23-34
• /
• 2012

In this study, we investigated the permeation property of single gases ($N_2$, $O_2$, $SF_6$, $CF_4$ through hollow fiber polymeric membrane (PSF, PC, PI) as a function of pressure and temperature to decide operating condition for $SF_6$ gas separation process. The results showed the gas permeation varied differentlydepending on the properties of gases and membrane. When permeance of each gases was represented as a function of temperature and pressure in 3 dimensional space, the surface of permeance was shown approximately flat. Thus, we established permeance models with forms of first-and second-order polynomial. These two models showed high goodness of fit. This indicates that the two polynomial models have enough applicability to predict the gas separation process.

• Korean Journal of Heritage: History & Science
• /
• v.53 no.1
• /
• pp.52-63
• /
• 2020

This study was conducted in order to evaluate the characteristics of air temperature fluctuation inside the Daegeumgul, Ondaldonggul, and Seongnyugul Caves, which are the most representative limestone caves in Korea, and also to assess the effects of air temperature on cave temperature. Temperature was measured hourly at three sites in Daegeumgul, Ondaldonggul, and Seongnyugul Caves from April 13 to June 25, 2019. Additionally, air temperature data for the areas around the caves was provided by the Meteorological Administration. Using this collected data, the basic statistical measure of fluctuation characteristics over time was ascertained, and time series analyses were performed. Wide variation of temperature was exhibited in the order of the cave entrance, the cave water inflow point, and the midpoint. Cave temperature was observed to increase gradually during the study period. There was a vast range in temperature at the Daegeumgul station located approximately 150 m outside the cave, but it remained nearly constant beyond the midpoint. Although the effect of air temperature was not significant due to the influence of visitors, the effect of air temperature on cave temperature gradually decreased from the entrance to the interior. At Ondaldonggul, there was a wide range in temperature recorded at the entrance due to the influence of air temperature, but it stayed almost constant in the interior. However, at the site where cave water flows into the cave, temperature was influenced by the cave water temperature. At Seongnyugul, there was a distinct fluctuation in temperature recorded at the cave entrance, while the middle of the cave remained nearly constant. Temperature fluctuated due to the air temperature at the entrance, while at the middle of the cave, measurements were expected to be affected to a greater extent by the lake water temperature than by the air temperature. However, this pattern was not observed. According to the time series analysis results, in all caves, fluctuations of air temperature affected cave temperature after approximately one hour. Cave size and structure, water presence, the entrance's size and shape, air flow, and visitor patterns can all influence cave temperature. Therefore, consideration of these factors is very important in the pursuit to clearly understand cave temperature characteristics.

• Membrane Journal
• /
• v.14 no.3
• /
• pp.201-206
• /
• 2004

The stability of the prepared silica membrane by chemical vapor deposition (CVD) method in the HI-$H_2O$ gaseous mixture was evaluated aiming at the application for hydrogen iodide decomposition in the thermochemical IS process. Porous $\alpha$-alumina having pore size of 100 nm was modified by the different CVD temperature using tetraethoxysilane as the Si source. The CVD temperature was $700^{\circ}C$, $650^{\circ}C$, and $600^{\circ}C$. The $H_2$/H$_2$ selectivities of the modified membranes which were measured by single-component permeation experiment showed 43.2, 12.6, and 8.7 at $600^{\circ}C$ for the M1 (CVD temperature was $700^{\circ}C$), M2 (CVD temperature was $650^{\circ}C$) and M3 membranes (CVD temperature was $600^{\circ}C$), respectively. Stability experiment in the HI-$H_2O$ gaseous mixture was carried out at $450^{\circ}C$. The prepared silica membrane at $600^{\circ}C$ of CVD temperature was more stable than that at the other CVD temperature.

• Journal of KIISE:Computer Systems and Theory
• /
• v.32 no.11_12
• /
• pp.629-638
• /
• 2005

In the System on a Chip design, the on chip bus is one of the critical factors that decides the overall system performance. Especially, in the case or reusing the IPs such as processors, DSPs and multimedia IPs that requires higher bandwidth, the bandwidth problems of on chip bus are getting more serious. Recently ARM proposes the Multi-Layer AHB BusMatrix that is a highly efficient on chip bus to solve the bandwidth problems. The Multi-Layer AHB BusMatrix allows parallel access paths between multiple masters and slaves in a system. This is achieved by using a more complex interconnection matrix and gives the benefit of increased overall bus bandwidth, and a more flexible system architecture. However, there is one clock cycle delay for each master in existing Multi-Layer AHB BusMatrix whenever the master starts new transactions or changes the slave layers because of the Input Stage and arbitration logic realized with Moore type. In this paper, we improved the existing Multi-Layer AHB BusMatrix architecture to solve the one clock cycle delay problems and to reduce the area overhead of the Input Stage. With the elimination of the Input Stage and some restrictions on the arbitration scheme, we tan take away the one clock cycle delay and reduce the area overhead. Experimental results show that the end time of total bus transaction and the average latency time of improved Multi-Layer AHB BusMatrix are improved by $20\%\;and\;24\%$ respectively. in ease of executing a number of transactions by 4-beat incrementing burst type. Besides the total area and the clock period are reduced by $22\%\;and\;29\%$ respectively, compared with existing Multi-layer AHB BusMatrix.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.3323-3328
• /
• 2007

Conventional LPG pump for Liquified Petroleum injection(LPi) engine has been adopted vane type. But the BLDC type fuel pump for LPi system has complicated structure and its price is high. Therefore, as a alternative, this study has mainly focused on the development of turbine type LPG pump which has lower cost and simple structure than conventional BLDC type. To verify the possibility of substitute the performance tests were performed for each fuel pump. The comparative items were pressure settling time, variation of fuel outlet temperature and engine performance of hot restart ability. As a result, performances of turbine type LPG pump were equivalent or high comparing to the BLDC type all over the tests for different fuel composition.

• Membrane Journal
• /
• v.10 no.4
• /
• pp.230-233
• /
• 2000

The aqueous glucose solution was separated by the membrane distillation with hydrophobic pojytetrafluoroethylcnc microfiltration membrane, The nominal pore size of the membrane was 0.2${\mu}m$. As the operating temperature increased from 40$^{\cirt}C$ to 70$^{\cirt}C$, the membrane permeation flux increased from 3.6 LMH to IL2 LlVIH, but the glucose rejection decreased 99% to 65% Also, the permeation nux and rejection decreased 25% and 6%, respectively, as the concentration of glucose solution increased 2 wt% to 4 wt%.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.11
• /
• pp.996-1000
• /
• 1998

This paper describes the characteristics of Pt microheater using aluminum oxide films as medium layer and its application to flow sensors. Pt microheater have heating temperature of $390^{\circ}C$ at heating power of 1.2 W. Output voltages of flow sensors which were fabricated by integrating sensing-part with heating-part increase as gas flow rate and its conductivity increase. At $O_2$ flow rate of 2000 sccm, heating power of 0.8 W, output voltage of flow sensor is 101 mV under bridge-applied voltage of 5 V.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.8 no.1
• /
• pp.57-66
• /
• 1997

1950년대 이래로 주로 군에서 발달되어 온 원격 탐사용 레이다에는 여러 종류가 있지만 주로 SLAR(Sidelooking Airborne Radar), SAR(Synthetic Aperture Radar), Scatterometer, Alti- meter 등이 많이 사용된다. SLAR와 SAR는 주로 넓은 지역의 레이다 영상을 얻는데 사용되기 때문에 영상 레이다라고 일반적 으로 분류된다. SLAR에서는 안테나 빔폭에 의해 분해능이 결정되기 때문에 원거리(특히 인공위성) 에서는 사용하기 곤란하다. SAR는 거대한 안테나를 시간적으로 합성해서 분해능을 향상시키는 방 식이므로 기본적으로 방대한 양의 데이타를 처리해야 하는데, 분해능을 좋게 할수록 필요한 신호 처리의 양은 기하급수적으로 증가한다. SAR의 기본 구성품은 일반적인 레이다와 크게 다를 바 없 으며, 단지 아주 작은 분해능을 실시간으로 요구할 때에는 막대한 계산량으로 인한 신호처리에서 의 병목현상을 적절히 처리하는 것이 중요한 연구 테마가 되고 있다.

• Proceedings of the KIEE Conference
• /
• 2008.10b
• /
• pp.386-387
• /
• 2008

수면의 인간의 생활 중에서 가장 흔히 볼 수 있는 행동형태의 하나로, 인간은 일생의 1/3 가량을 수면시간을 보낸다. 적절한 수면은 인간의 신체적, 심리적 건강을 유지하고 활기차고 밝은 사회생활을 하는데 큰 도움을 준다. 한편, 생활 방식의 변화에 따른 과도한 스트레와 외부환경적인 원인 등으로 인해 수면장애를 호소하는 인구가 늘어나고 있다. 이에 본 연구에서는 압력센서와 온도센서를 이용하여 저비용 고효율적인 수면형태 감지시스템을 설계 하였다. 제안된 시스템을 침대에 설치하여 수면중 수면자의 머리, 허리, 발에서 나오는 데이터측정을 통해 유용성을 검토하였다. 또한 측정된 데이터를 bluetooth를 이용해 전송함으로써 실시간으로 수면형태의 모니터링 할 수 있는 기본적인 시스템을 구축하였다.

• Membrane Journal
• /
• v.1 no.1
• /
• pp.24-33
• /
• 1991

합성고분자막을 이용하여 액체혼합물을 분리하는 공정은 오래전부터 알려져 왔다. 바다물로부터 역삼투법이나 전기투석법을 이용하여 탈염하는 공정이라든지 한외여과 또는 정밀여과법을 이용하여 초순수를 제조하는 공정등은 현재 대단한 기술적, 상업적 의미를 갖으며 산업적으로 발전하고 있다. 더욱 최근에는 합성고분자막이 여러 기체혼합물 분리에 응용되고 있다. 예를 들면 석유화학 폐가스나 암모니아 공장에서 수소의 회수나 공기중의 산소나 질소의 부화등은 막이 아주 유용한 도구로 사용되어 온 두가지 중요한 분야이다. 고분자막이 특정한 물질분리에 맞도록 고안될수 있게 된 이래로 재래식 방법으로는 곤란한 분리문제들이 막공정에 의해 다루어질수 있게 되었다. 이같은 문제중 하나가 폐수중 유기용제등 유기물의 제거이다. 특히 할로겐화 유기물, 살충제, 농약등 오래전부터 독극물로 알려져온 물질들을 폐수로 부터 제저하는데 많은 노력이 경주되어 왔다. 이러한 연구에도 한외여과법이나 역삼투법등의 막분리공정이 응용되어 보고된 바 있다.