• 대한기계학회논문집B
• /
• 제25권8호
• /
• pp.1053-1059
• /
• 2001

Results from direct numerical simulation and LDV measurements are analyzed to investigate the influence of structured surface on turbulence in the outer layer. To provide a well-defined surface roughness, sinusoidal wavy surface was used. Even though flows over smooth and wavy surface show very different process for maintaining turbulence in the vicinity of the wall, there are some evidences that the turbulence in the outer layer has a universal characteristics and it may be possible to give a speculative interpretation that similarity of turbulent structures arises because Reynolds stress producing motion is similar regardless of different turbulence generation mechanisms embedded in both cases.

• 설비공학논문집
• /
• 제14권11호
• /
• pp.954-963
• /
• 2002

For the optimal design of an automotive blower system, effects of the scroll cut-off starting angle, the clearance between blade tip and bellmouth, and the scroll expansion angle on the performance of sirocco fan are investigated experimentally. Best performance is achieved at fan exposure ratio $\Deltae/r_c$,/TEX> =1.0, and clearance ratio $\DeltaeC/C=0.62. Flow characteristics inside sirocco fan are also studied by using LDV. Flow patterns in the inside of fan can be classified into three regions. Velocity vector has the same direction as rotational direction of fan at 0~$120^{\circ}$, toward the fan blades at 150～$180^{\circ}$, and opposite direction at 210~$330^{\circ}$. Turbulent intensity is relatively high near the cut-off edge in the scroll housing.

• 전자공학회논문지A
• /
• 제28A권5호
• /
• pp.361-369
• /
• 1991

The optics and the signal processor of dual beam laser Doppler velocimeter(LDV) was fabricated. By using the dual beam and the forward scattering, the optics part of LDV was fabricated. And the signal processor of LDV was designed by the frequency counter type using new 11:6 period timing device in order to remove error signals, and was made of the reference clock of a 500 MHz ECL oscillator. Doppler frequencies from 10KHz to 70MHz can be measured using the signal processor. In the accuracy of the period counting part, from 1.81x10**-4% to 1.27% is estimated, and in the accuracy of the validation logic part, from 0.78% to 14.78% is estimated.

• 대한조선학회논문집
• /
• 제28권2호
• /
• pp.132-145
• /
• 1991

캐비테이션 터널내에서 프로펠러 축 주위의 난류유동 특성을 레이저 유속계(LDV)를 이용하여 측정하였다. 우선 캐비테이션 터널의 시험부에서 유동의 균일도 및 난류유동 특성을 조사하였으며, 다음은 프로펠러 축 주위의 난류유동 장을 축 주위의 난류경계층 및 후류에서 조사하였다 프로펠러 축주위의 경계층 유동 내에서는 일반적인 축 대칭 난류경계층 유동장의 특성이 잘 나타난 반면, 축 후류의 반류유동장에서는 복잡한 유동장이 발견되었다.

• 설비공학논문집
• /
• 제14권9호
• /
• pp.766-773
• /
• 2002

Flow distributions in a rectangular duct with two branch ducts are measured by 5 W laser doppler velocity meter. The fluid flows are also computed by commercial soft-ware of STAR-CD for comparison between them. The Reynolds numbers in the main duct are from 4,226 to 17,491. The ratios distributed into two branches from the main duct are in-variant to Reynolds numbers according to both of numerical and experimental results. However computed velocity profiles at exit of each branch are somewhat different from measured profiles at the same location.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 1999년도 유체기계 연구개발 발표회 논문집
• /
• pp.227-233
• /
• 1999

Detailed Measurements were made to investigate the turbulence characteristics of a leakage vortex in an axial-flow fan using three-dimensional LDV. The turbulence in the leakage vortex has highly anisotropic characteristics with the radial value being the maximum. The turbulence intensity components in the vortex in the streamwise and tangential directions increase up to a certain downstrean position and then decrease. This increase is mainly due to the rapid decrease of the streamwise velocity of the vortex and partly due to the radial gradient of the streamwise velocity caused by a velocity deficit. As the vortex decays moving downstream, turbulence intensity also decrease gradually.

• 한국기계기술학회지
• /
• 제20권6호
• /
• pp.757-762
• /
• 2018

LDV(laser Doppler velocimetry) measurements were conducted on the exit region of the impeller passage and the gap between the impeller and turbine blades under 0.8 speed ratio. The 0.8 speed ratio has an impeller speed of 2000rpm and a turbine speed of 1600rpm. A periodic variation of the mass flow rate is present in many of the measurements made. The frequency of this variation is the same as the frequency of the turbine blades passing the impeller passage exit. It is found that the instantaneous position of the turbine had effect on fluid flow inside the impeller passage and gap region. This study would aid in the construction of higher accuracy CFD models of this complex turbomachinery device.

• 한국가시화정보학회지
• /
• 제19권2호
• /
• pp.48-55
• /
• 2021

In order to design a propeller with high efficiency and excellent cavitation performance, theoretical and experimental studies on the cavitation and noise characteristics according to the blade section shape are essential. In general, sheet cavitation, bubble cavitation, and cloud cavitation are the main causes of hull vibration and propeller surface erosion. However vortex cavitation, which has the greatest influence on the noise level because the fastest CIS in ship propeller, has been researched for a long time and studies have been conducted recently to control it. In this experiment, the development process of cavitation was measured by using three dimensional wings with two different wing section and wing tip shapes, and the noise level at that time was evaluated. In addition, we evaluated the relationship between cavitation inception and hydrodynamic force using three component load cell and we measured the velocity field of wing wake using LDV.

• 대한기계학회논문집B
• /
• 제32권2호
• /
• pp.158-165
• /
• 2008

The carbon dioxide properties change sharply near the critical or pseudo-critical point in the heat transfer processes. The reduction in turbulent, convective heat transfer parameters observed in some supercritical data and in experiments with common gases can be due to property variation, acceleration, buoyancy or combinations of these phenomena, depending on the conditions of the applications. In this study, the measurement for the secondary flow driven by buoyancy was carried out on the supercritical carbon dioxide turbulent flows in the different boundary condition with the constant mass flow rate. The available measuring techniques were used to clarify the behaviour of any supercritical fluid. Laser Doppler Velocimeter (LDV) and a special device was used to measure the secondary velocity and turbulent characteristics of the supercritical flows.

• 대한기계학회논문집
• /
• 제11권5호
• /
• pp.725-730
• /
• 1987

본 연구에서는 2사이클 기관의 흡입 포오트 부근의 가스 유동을 레이저 도플 러 유속계를 이용하여 측정하고 가스의 평균 속도, 속도 변동, 유속 벡터 등을 기관의 회전 속도, 실린더 헤드의 모양 및 실린더로의 흡입 속도 측정점의 위치 변화에 대하 여 비교 검토하고, 유동 특성을 고찰하였다.