• Journal of IKEEE
• /
• v.16 no.1
• /
• pp.34-44
• /
• 2012

This paper proposes a practical compensation method by using digital signal processing over the creep error which is representative in strain gauge loadcell. The signal compensation method carry out the simulation by deciding compensation constant (time constant) and coefficient measuring the loadcell output response. Then, compensation constant and coefficient are stored on the microprocessor. By using calculated on microprocessor creep error compensation values, weighting value is showed as a digital signal by reducing error values measured through output signals of loadcell. In addition, we apply error compensation method in order to have a dedicated software for loadcell electronic scale. This technique is useful because it has great influence on error rate reduction that has been produced by conventional electronic scales (0.03%). As a result our technique gives better accuracy (0.01%~0.003%) as what is given by digital electronic scale, while it has less complex operation processing.

• Proceedings of the KIEE Conference
• /
• 2003.07d
• /
• pp.2726-2728
• /
• 2003

본 논문에서는 디지털 로드 셀의 국산화 결과를 보고한다. 개발된 로드 셀의 특성은 다음과 같다. A/D분해도: 20 bit, 변환속도: 100 Hz, 정도: < 0.02% R.O., 반복특성: < 0.01% R.O. 사용온도범위: $-20{\sim}80^{\circ}C$, 온도특성: < 0.03% R.O./$10^{\circ}C$, 진단기능: 자체내장, 자체보정기능: 온도, 편심오차, 크리프 보정기능 내장, 보호회로: surge lightening.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.11 no.1
• /
• pp.114-122
• /
• 1997

This paper describes the design and development of a smart digital load cell used forweighing installations. Sice the load cell sensor to be used is very sensitive for weight cariation, the load cell must have the temperature stability, low-drift and the high-resolution of the A/D conversion for accuracy. A new analog circuit which is controlled by one chip micro-processer has been developed to reduce the offset voltage and the drift characteristics of operational amplifiers, and has been adapted into the digital load cell. Also, a software algorithm has been developed to obtain the stable and accurate A/D conversion. This software includes a RS-485 communication program to control the digital load cell, which gives a capability of backing-up the calibration data and transferring control data. The simulation and evaluation of the designed digital load cell has been shown as having the good performance. which will give useful application to the weighing installations as a remote weighing sensor.

• Journal of Industrial Technology
• /
• v.23 no.A
• /
• pp.55-61
• /
• 2003

In this study, a signal processing and related techniques for development of a weight measuring system using a digital loadcell which is able to satisfy the important properties of WIM (weighing-in-motion) system have been investigated. A fast and high accurate signal processing of the digital load cell sensor for weighing-in-motion system is presented. A/D conversion system is constructed to realize a stable A/D conversion and signal processing algorithm using DSP and microprocessor. A new technique for vibration and measuring speed of the system is also investigated. The proposed method was applied to the actual design and the experimental results showed good performance of the weighing speed and stability.

• Journal of the Korea Convergence Society
• /
• v.8 no.11
• /
• pp.49-56
• /
• 2017

Curling sweeping is one of important motion to control the position of the curling stone, and sweeping speed and applied force to the broom pad are major research subjects. In this study, a device was developed to measure the force applied to the curling broom pad in curling sweeping motion, and two load cells were mounted between the broom pad and pad holder. Analog signals generated from the load cells were sampled about 300 times per second using a micro controller, and then converted to 10-bit digital signals. Calibration of the load cell and set up of regression equations to convert the measured electrical signals into mass (force) was done by three M1 class weights, and the developed system was designed as wearable device to minimize increasing of total weight of the broom. Same force was applied to the developed system and a force plate that was using as a reference force measurement system in field of sports, and the difference between the measured values were showed about $0.909{\pm}1.375N$(mean and standard deviation). The developed system could be applied other kinds of study which required force measurement function similar to sweeping motion.

• Proceedings of the KIEE Conference
• /
• 2007.04b
• /
• pp.107-109
• /
• 2007

From composition transmitter is detached in indicator to individual load direction of 2 channels and adding up display by digital load cell indicator indication method of Bluetooth method is identifying marks.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.15 no.1
• /
• pp.59-69
• /
• 2001

Ths paper presents an algorithm of detecting eccentricity signal and diagnosing the cause in rolling process. A designed technique uses only the outputs of load cell and tachorreter, which are generally utilized in rolling process, and need not any acklitional sensors. Detecting signals related to eccentricity is done by combining outputs of 6 digital bandPass filters whose center frequency are varied with roll's rotating frequency. A function of diagnosing the cause of occentricity from extracted data having occentricity components is implemented by defining reasonable variables. In order to show validity of an algorithm designed in this paper, simulation was accomplished for three groups. The first is that some portion of roll in the direction of roll circumference is distorted. The second is that rotating axis and roll center is not identical. The third is that composite cause is occmed Simulation results show that every kind of eccentricity can be diagnosed in terms of algorithm proposed.oposed.

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1514-1516
• /
• 2003

NiCrFe 박막을 이용한 정밀급 박막 스트레인 게이지를 개발하였으며, 그 특성을 요약하면 다음과 같다. 스트레인한계: 5 % 이하, 저항: 350 ${\sim}$ 2,000 ${\Omega}$, 게이지 율: 2.1, 정도: 0.1 %, 피로한계 : $10^6$ at ${\pm}1500{\mu}{\varepsilon}$, 사용온도범위: $-75{\sim}150^{\circ}C$, 온도 출력: ${\pm}1{\mu}{\varepsilon}/^{\circ}C$, 게이지율변화 : +0.009%/$^{\circ}C$ 국산화된 박막 스트레인 게이지는 디지털 로드 셀 등에 적용할 수 있으며, 이 분야의 국내 기술력 향상에 이바지 할 것이다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.1A
• /
• pp.1-10
• /
• 2012

Along with the development of coasts, islands and mountains, the demand of long-span bridges increases which, in turn, brings forth the construction of cable-supported bridges like suspension and cable-stayed bridges. There are various types of statically indeterminate structures widely applied that supported the main girder with stay cables, main cables, hanger cables with aesthetic structural appearance. As to the cable-supported bridges, the health monitoring of a bridge can be identified by measuring tension force on cable repeatedly. The tension force on cable is measured either by direct measurement of stress of cable using load cell or hydraulic jack, or by vibration method estimating tension force using cable shape and measured dynamic characteristics. In this study, a method to estimate dynamic characteristics of hanger cables by using a digital image processing is suggested. Digital images are acquired by a portable digital camcorder, which is the sensor to remotely measure dynamic responses considering convenient and economical aspects for use. A digital image correlation(DIC) technique is applied for digital image processing, and an image transform function(ITF) to correct the geometric distortion induced from the deformed images is used to estimate subpixel. And, the correction of motion of vision-based measurement system using a fixed object in an image without installing additional sensor can be enhanced the resolution of dynamic responses and modal frequencies of hanger cables.

• Tunnel and Underground Space
• /
• v.19 no.6
• /
• pp.473-478
• /
• 2009

The accuracy of point load apparatus is depend on point to point coaxial fitting. Also, the estimation of applied point load using the pressure gauge frequently lead to erroneous results. An improved point load apparatus has been developed in this study by mounting linear bearing on polished support rod, and eccentric error of point to point axis has been sustained less than 0.1 mm even under series of extreme work load conditions. Two digital displacement gauges are attached to measure the distance from point to point with sample specimen. A load cell mounted at the end of upper conical platen measure the applied net load on sample instead of preassure gauge. Total of 107 point load tests has been achieved to assure the quality and performance of developed apparatus. This exercise turned out to be successful.