• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.1
• /
• pp.105-113
• /
• 2009

The performance of a direct-injection type diesel engine often depends on the strength of swirl or squish, shape of combustion chamber, the number of nozzle holes, etc. This is of course because the combustion in the cylinder was affected by the mixture formation process. In this paper, combustion process of biodiesel fuel was studied by employing the piston which has several grooves with inclined plane on the piston crown to generate swirl during the compression stroke in the cylinder in order to improve the atomization of high viscosity fuel such as biodiesel fuel and toroidal type piston generally used in high speed diesel engine. To take a photograph of flame, single cylinder, four stroke diesel engine was remodeled into two stroke visible engine and high speed video camera was used. The results obtained are summarized as follows; (1) In the case of toroidal piston, when biodiesel fuel was supplied to plunger type injection system which has very low injection pressure as compared with common-rail injection system, the flame propagation speed was slowed and the maximum combustion pressure became lower. These phenomena became further aggravated as the fuel viscosity gets higher. (2) In the case of swirl groove piston, early stage of combustion such as rapid ignition timing and flame propagation was activated by intensifying the air flow in the cylinder. (3) Combustion process of biodiesel fuel was improved by the reason mentioned in paragraph (2) above. Consequently, the swirl grooves would also function to improve the combustion of high viscosity fuel.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.4
• /
• pp.641-647
• /
• 2017

In order to meet the stricter emission regulations, the proportion of after-treatments for vehicles and vessels has been increasing gradually. The objective of this study is to investigate the physicochemical properties according to ash cleaning agents of CDPF for Diesel Engines. Penetrating agents with strong penetration into ash and a surfactant component to mix water and oil were prepared properly. The cleaning characteristics of S1 sample were good. Washcoat loss rate of S1 sample was lower by about 2.2% because of less KOH component and lower Na2SiO3 content. Washcoat loss rate of S4 sample with an added KOH and Na2SiO3 components by penetration agents was increased by about 13%. In terms of less than about 13% of CDPF's washcoat loss rate, it was able to reduce the harmful gas components.

• Journal of Power System Engineering
• /
• v.16 no.3
• /
• pp.10-15
• /
• 2012

Recently we have a growing interest in environmental pollution and alternative energy. Diesel engine is generally used to produce the power on the ground and the sea. However, the combustion characteristics are changed on account of the wear of fuel system and the altered ambient condition of the combustion chamber by the increment of the engine operation hour. Therefore combustion characteristics on fuel injection timing are experimentally investigated to find out the optimum fuel injection timing in the case of the aged diesel engine using biodiesel blend oil. Cylinder pressure, rate of pressure rise, rate of heat release and combustion gas temperature are risen by the advancing fuel injection timing, while the exhaust gas temperature and soot emission level are decreased by the advancing of fuel injection timing. The least specific fuel oil consumption is indicated at BTDC $26^{\circ}$ CA on the 75%load and at 1800rpm.

• Journal of Power System Engineering
• /
• v.12 no.1
• /
• pp.5-12
• /
• 2008

We measured emission characteristics of CRDI diesel engine equipped with a commercial CPF. Experimental parameters adopted a neat diesel fuel, a blend of diesel fuel with 20% biodiesel, a blend of diesel fuel with 15% biodiesel and 5% ethanol. The experiments were carried out to measure the emission and engine performance according to ESC 13-mode cycles. The maximum torque with biodiesel blend fuel is slightly lower than that of neat diesel fuel in the entire the 13-mode cycles, and 5% ethanol and 15% biodiesel blend fuel is slightly higher than that of neat diesel fuel. THC and CO emissions of the biofuel blended diesel fuel were slightly increased and decreased, and mean conversion efficiencies of THC and CO on the commercial CPF were achieved about 70$\sim$87% in the ESC 13-mode. From the measurement by the Scanning Mobility Particle Sizer(SMPS), the total number and mass of nano-sized particles by a commercial CPF were decreased about 97.8% and 96.8 % in the range of the nano-size from 10.6 to 385nm, respectively.

• LP가스
• /
• v.22 no.5
• /
• pp.34-37
• /
• 2010

국가 에너지원의 다원화와 환경공해 저감은 정부의 저탄소 녹색성장 정책과 에너지 안보를 위해 달성해야만 하는 필수불가결한 과제로 자리 매김한지 오래이다. 또한, 화석연료의 환경문제 유발과 석유자원의 고갈위기 등으로 인해 이를 대체할 수 있는 신재생에너지 개발에 대한 관심이 고조되고 있으며 이러한 과제를 해결하기 위한 친환경 연료로써 DME(Dimethyl ether)에 대한 관심이 날로 증가하고 있는 추세이다. 특히 높은 세탄가를 지니고 물성이 LPG와 유사하여 디젤차량 및 LPG 대체 연료, 연료전지 등의 다양한 용도로 사용할 수 있고 수송 저장 수단, 인프라 구축 등의 장애가 적다는 장점이 있으며, LPG와 물리적 특성이 비슷해 기존 LPG 인프라를 개조하지 않고도 LPG와 혼합해 난방 및 취사뿐 아니라 차량 연료용으로도 시범사업이 활발히 추진되고 있는 상황이다. 그밖에도 액화상태로 저장 운송 등의 취급이 용이하다는 장점이 있다. 한국가스공사의 경제성 분석 결과, 본격 보급시 LPG대비 20~30% 저렴하게 공급가능하다고 판단되어짐에 따라 LPG사용자 부담을 완화할 수 있는 기대를 가지게 한다. 이에 우리협회는 지경부 한국가스공사등과 함께 프로판에 DME가 20%의 혼합된 DME혼합연료 소비자에게 보급하는 시범사업을 전개하고 있으며 현재까지 진행된 내용과 향후 계획등을 소개함으로써 DME에 대한 이해를 높이고자 한다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.260-262
• /
• 2008

최근 고유가의 지속과 국제적인 환경 규제에 대응하기 위하여 환경친화적인 대체연료의 개발이 시급한 가운데 재생가능한 동식물성 유지로부터 생산되는 바이오 디젤에 대한 연구가 활발히 진행되고 있다. 특히 자원 재활용 및 에너지 생산관점에서 폐유지로부터 바이오디젤 원료로 사용하는 연구가 활발히 진행되어 왔다. 이러한 폐유지로부터 바이오디젤을 효율적으로 생산하기 위해서는 폐유지내 함유되어 있는 유리지방산을 전처리공정에서 산촉매에 의한 에스테르화 반응에 의해 전환제거하고자 한다. 본 연구에서는 폐유지내 함유된 유리지방산 전환제거에 효과적인 불균일계 이온교환수지 촉매를 이용하여 공정변수 즉 사용된 촉매의 양, 반응온도, 유리지방산 농도에 따른 유리지방산 전환제거특성을 조사해 보았다. 또한 각각의 반응조건에서 속도상수를 계산하여 이온교환수지 촉매를 사용한 유리지방산 전환 제거에 필요한 활성화 에너지 값을 구하였다.

• Proceedings of the KAIS Fall Conference
• /
• 2010.11a
• /
• pp.298-300
• /
• 2010

화석 연료인 석유, 천연가스, 석탄의 점진적 고갈이 예상됨에 따라 전 세계는 석유와 유사한 성질을 갖는 바이오 오일을 에너지원 및 화학원료로 사용하려는 노력이 증가하고 있다. 바이오 오일 활용분야 중 가장 큰 부분을 차지하고 있는 것은 바이오 디젤로 식물성 오일과 알콜의 전이에스테르화 반응에 의하여 생산되며, 바이오 디젤 1톤당 100kg의 글리세롤이 부산물로 생성된다. 본 연구에서는 바이오 디젤 부산물인 폐글리세롤을 이용하여 다양한 유도체의 생산 및 그 유도체의 가능성에 대하여 살펴보았다.

• Journal of Power System Engineering
• /
• v.6 no.3
• /
• pp.11-16
• /
• 2002

This paper describes the power performance and emission characteristics of the high speed direct injection diesel engine (2.9 litter displacements) driven by soybean oil asknown a bio diesel fuel. The results were compared to diesel fuel with blending bio diesel fuels. The soybean bio diesel fuel was added in the diesel fuel in concentration varying from 25% to 75% volume rates. We measured the emissions according to ECE 13 mode and full load, fixedengine speed. When the 25% bio diesel fuel was used, NOx emission at the ECE 13 mode test slightly decreased compared with diesel base engine. Over engine speed of 2000 rpm, the level of unburned hydrocarbon(HC) and carbon monoxide(CO) were the same to the diesel engine. Smoke emission decreased asthe blending bio diesel fuel rate increased.

• Journal of ILASS-Korea
• /
• v.12 no.1
• /
• pp.30-37
• /
• 2007

Dimethyl ether (DME) as an alternative fuel for compression ignition engine was investigated by measuring spray development processes, injection rate profiles, engine performance, and exhaust emission characteristics. The results of DME fueled engine were compared with those obtained by fueled with diesel. The experimental results showed that DME has approximately 0.03ms shorter injection delay and higher maximum injection rate than those of diesel fuel at a constant injection pressure of 50MPa. The spray visualization indicates that DME has shorter spray tip penetration due to its low density and faster evaporation. The combustion characteristics of DME operated engine provided faster ignition delay and three times shorter combustion duration. It is believed that the better evaporation and atomization characteristic of DME contributes the faster combustion. At all operating condition, soot emission was not detected due to the clean combustion of DME.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.666-668
• /
• 2007

에너지 사용량의 증가와 국제적인 환경 규제에 대응하기 위하여 환경친화적인 연료의 개발이 시급한 가운데 재생가능한 동식물성 유지로부터 생산되는 바이오 디젤에 대한 연구가 활발히 진행되고 있다. 특히 자원 재활용 및 에너지 생산관점에서 폐식용유로부터 바이오디젤 원료로 사용하는 연구가 활발히 진행되어 왔다. 이러한 폐식용유를 이용한 바이오디젤 생산에서 폐식용유내 함유된 유리지방산 및 수분에 의해 효율적인 전이에스테르화 반응이 어렵기 때문에 이를 전처리 단계에서 제거되어야 한다. 본 연구에서는 폐식용유내 유리지방산을 효과적으로 제거하기 위하여 회분식 반응기에서 MFI 제올라이트 촉매를 이용하여 Si/Al 몰비에 따른 산세기 및 산량의 변화에 따른 유리지방산 제거 특성을 조사해 보았다.