• International Journal of Highway Engineering
• /
• v.14 no.2
• /
• pp.83-91
• /
• 2012

This study deals with the operational efficiency of roundabout. The roundabouts generally have such the merits as high capacity, delay reduction, safety improvement, and others. Circular intersection can be divided into the rotary and roundabout according to travelling priority. The objective of this study is to comparatively analyze the operational efficiency of rotary and roundabout by scenario. In pursuing the above, this study gives the particular attentions to developing 256 scenarios according to the directional and entering traffic volume and analyzing the delay using VISSIM. The main results are as follows. First, the average delay of rotary was analyzed to be 1.56-8.74 times of roundabout. Second, the operational efficiencies of rotary and roundabout were analyzed to be better in the case of bigger differences in the traffic volumes between the main and minor roads. Third, the average delay of the 4-legged was evaluated to be 1.77-11.70 times of 3-legged intersection. Finally, 2-lane intersection (3-legged & 4-legged) was analyzed to be 2.02-2.23 times of 1-lane intersection.

• International Journal of Highway Engineering
• /
• v.4 no.3 s.13
• /
• pp.25-33
• /
• 2002

Most national highways are paved with asphalt. Since increased traffic volume and high temperature have reduced the service life of pavements, modified asphalt pavements or stone mastic asphalt (SMA) have gradually been adopted. However, pavement engineers have difficulty to select pavement types due to lack of standard specifications for these new pavement types. In this study, service lives of general asphalt pavements based on traffic volume were analyzed using the inventory data of pavement management system (PMS) collected for last 10 years. The results showed 9.5 and 5.6 year average service lives for new constructed pavements and overlays, respectively. The traffic volumes for the design life of 10 years was presented based on confidence levels using service life distributions of current pavements. For the confidence level of 90%, 2,300 ESAL was obtained; 1,500 ESAL for the confidence level of 80%. This indicates that modified asphalt pavements should be considered for sections with the higher traffic volume.

• International Journal of Highway Engineering
• /
• v.9 no.3
• /
• pp.21-28
• /
• 2007

We suggest a new spatial linear interpolation method to substitute linear interpolation method which widely used in transportation engineering to impute the missing daily traffic volume. We layout daily traffic volume which is time series data over the virtual lattice space to consider the spatial correlation. We used Moran Index to evaluate the spatial correlations among daily traffic volume in same week and same date traffic volume by week considering the circularity of daily traffic volume. For real application, we used daily traffic volume on November, 2004 provided by Korea Institute of Construction Technology(KICT) and transformed daily traffic volume to 4 times 7 virtual lattice space to reflect the spatial correlation. Finally we showed that the spatial linear interpolation method has good performance for missing data imputation based on MAPE, RMSE, and Theil's U criteria.

• International Journal of Highway Engineering
• /
• v.10 no.4
• /
• pp.151-159
• /
• 2008

Performances of retroreflectivity vary place to place, according to traffic volumes and time lengths after striping, depending on pavement marking materials and colors. The present paper uses the nation wide data of retroreflectivity, which has been collected from freeways and then tries to develop the regression curve setting traffic volume and service life as independent variables and retroreflectivities as dependent variables. The DB system includes two year's measurement in $2005{\sim}2006$ over Korean freeway pavement marking at an interval of three months for the period. The mobile measurement system, a laserlux, was employed for the purpose. The DB has provided a lot of information about materials and performance of the specific pavement marking such as geometric features, traffic volumes, material characteristics and the installation date. This study provides the comparison of pavement marking performances under diversified conditions. Based on accumulated pavement marking performances, this study provides performance curves based on the diversified factors. The goal of the retroreflectivity modeling is to develop equations that can be used to estimate an average retroreflectivity of pavement markings as a function time since application and traffic volume. After representing the variation of retroreflectivities and estimating regression curves by linear, exponential, logarithmic and power function, the regression curve which had the highest coefficient of determination and the value similar to the last field measurement was regarded as the retroreflectivity decay model. As a result of verification, the decay model showed the signification within the 90% confidence level and especially showed the clear relation with field data according to increase of cumulative vehicle exposure. Accordingly, these models can be used to determine service lives, retroreflectivity degradation rates, and retroreflectivity of new markings.

• International Journal of Highway Engineering
• /
• v.12 no.4
• /
• pp.79-86
• /
• 2010

This study deals with the roundabout installed at the diamond interchange. The goal is to analyze the relative effectiveness of roundabout to signalized intersection. In pursuing the above, this study gives the particular attentions to comparing the performances using VISSIM software. The main results analyzed are as follows. First, the single and double roundabouts are analyzed to have the rapid change of delay in the case of total entering vehicles of more than 2,400pcph for directional rate 10:5:5, 2,800pcph for 10:8:2, and 4,400pcph for 10:2:8. Second, the roundabouts are evaluated to be more effective than signalized intersection in the case of total entering vehicles of less than 4,000pcph for directional rate 10:5:5, and 4,400pcph for 10:2:8. In the case of directional rate 10:8:2, double roundabout of total entering vehicles less than 5,600pcph is analyzed to be more effective than signalized intersection. Finally, the performance of double roundabout is analyzed to be very similar to that of single roundabout in the case of total entering vehicles less than 4,400pcph. However, the double roundabout is evaluated to be more effective than single in the case of total entering vehicles more than 4,400pcph.

• Journal of Korean Society of Transportation
• /
• v.23 no.2
• /
• pp.95-106
• /
• 2005

Road accidents are considered as the result of a complex interplay between road, vehicle, environments, and human factors. Little study, however, has been carried out on the attributes of human factor compared to the road geometric conditions and traffic conditions. The previous researches focused on mainly both traffic and geometric conditions on specific location. Therefore, it's hard to explain phenomenon of the high traffic accident rates where road and traffic conditions are good. Because of these reasons, accident analysis has contributed on geometric improvement and has not contributed on traffic management such as selection of attention section, driver napping alert, etc. The freeway incident management is also associated with reliable prediction of incident occurrences on freeway sections. This paper presents a method for estimating the effect of trip length on freeway accident rate. A PAR (Potential Accident Ratio), the new concept of accident analysis, considering TLFDs (Trip Length Frequency Distributions) is suggested in this paper. This approach can help to strengthen freeway management and to reduce the likelihood of accidents.

• International Journal of Highway Engineering
• /
• v.13 no.4
• /
• pp.167-175
• /
• 2011

Evaluation of fuel consumption for the various road condition and vehicle type is necessary to perform the economic analysis of road construction which is important for the efficient design and management of road. Economic analysis of road should consider the social cost which can be divided into agency cost including initial construction expense, maintenance cost, and so on, and user cost consisting of vehicle operating cost, congestion cost, etc. Since vehicle operating cost depends on the traffic volume, fuel consumption that is a major part of vehicle operating cost will change by traffic volume as well. Fuel consumption is significantly affected by vehicle speed and road condition, especially the roughness. Thus, fuel consumption should be evaluated in terms of road condition, which is not currently considered. In this study, the estimation model of fuel consumption for the passenger cars in Korea has been developed by considering the road condition. First, the relationship between vehicle speed and fuel consumption that is used to calculate the vehicle operating cost for investment evaluation of transportation facility and the initial feasibility study of road construction was investigated. Second, with the consideration of road roughness, fuel consumption of the passenger car was measured. From the measurement, it was found that fuel consumption increased by $80m{\ell}$ per 100km driving as the roughness increased by 1m/km. Therefore, it is recommended that for the economic analysis of road design and management, the fuel consumption should be a function of road roughness.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.4
• /
• pp.1619-1629
• /
• 2013

It turned out that there was a direct or an indirect relationship among global warming, urban heat island effects, urban and traffic environments, and public's health. In particular, unusual climate phenomena such as frequent heavy rainfall and scorching heat in a row that had rarely happened before have a negative effect on quality of life for people living in urban areas. This study focuses on the effects of roadway geometric design and traffic conditions on air temperature of roadside in Seoul Metropolitan Areas, controlling of roadway micro-climate environment. Five roadway segments containing different roadway and traffic conditions in terms of traffic median with trees, street trees, traffic volume and average travel speeds were surveyed. According to statistical results(t-test) from three roadway air temperature regression model estimations, air temperature is found to be different from one another in three periods-morning, afternoon and evening. Regarding roadway geometric design, air temperature of urban roads with vegetated median strips is lower about 1.3~2.2 degrees in celcius. Higher traffic volumes per lane and lower average travel speeds will tend to increase roadside air temperature, and efficient traffic operation policies can protect from increasing roadside air temperature in urban areas.

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 2003.05b
• /
• pp.223-224
• /
• 2003

포장도로에서 발생되는 미세먼지는 주로 자동차의 운행에 의한 직접 배출되는 입자와 도로 표면에서 비산되는 토양입자 그리고 타이어나 브레이크 패드의 마모에 의한 고무 및 석면 둥 다양한 배출원에 의해 발생되는데, 도로 주변의 배출원에 의해 많은 영향을 받을 것으로 판단된다. (최금찬등, 1996) 특히 인천에는 많은 비산먼지 배출원이 산재하여 있어, 이 들 배출원들의 영향이 여타 대도시보다 클 것으로 판단된다. 따라서, 본 연구에서는 인구와 교통량이 많고 공업활동이 활발한 인천지역의 주요 포장도로(H-ADT: High Average Daily Traffic, 5,000대/일 이상인 도로)에서 채취한 silt를 주거지역, 공업지역, 상업지역, 기타지역별로 채취하여 화학적 성분분석을 통해 지역별 특성을 조사하여, 각 지역 별 포장도로에서의 silt의 기원이 무엇인지를 추정하는 기초자료를 구축하고자하였다. (중략)

• Journal of Environmental Health Sciences
• /
• v.27 no.4
• /
• pp.99-105
• /
• 2001

도로교통소음은 많은 지역에 산재해 있으며 특히 주도로변에 거주하는 사람들에게 환경과 관련하여 매우 중요하다. 도로교통으로부터 소음수준을 계산하는데 몇가지 다른 방법들이 이용되고 있다. 이 방법들은 계산방법과 그래프식 그리고 컴퓨터 모델링 기술 등이다. 교통과 교통소음의 영향으로부터 소음을 계산하는 간단한 기술의 예측방법은 여기에 나타내었다. 이 TNS (traffic Noise Screening) 방법은 서로 다른 도로유형에 대한 일련의 도로교통소음레벨의 예측그래프로 전개된 것이다. 이 그래프는 Federal Highway Administration (FHWA) STAMINA 2.0을 이용하여 다양한 시나리오에 대한 소음 예측모델을 계산한 결과를 기초하였다. TNS에 도로의 기하학적 형태, 교통량 주행속도 그리고 도로중앙선의 거리등의 데이터를 입력시킨다. TNS 그래프는 소음영향과 연관된 교통소음예측에서 사용하는 경우 교통소음레벨의 계산을 쉽게 한다. 이 TNS 방법은 STAMINA 2.0과 같은 상세 모델링을 대신하지는 못하지만 상세 모델을 필요로 할 때 도움을 주는 도구이다 만약 소음계산들이 중요하거나 또는 시나리오가 보다 복잡하고 부가된다면 보다 상세한 모델링이 수행되어져 스크린 결과들이 나타난다.