• LP가스
• /
• 통권71호
• /
• pp.49-53
• /
• 2000

대형디젤엔진의 대체용으로 LPG 엔진을 개발함에 있어서 차세대 연료공급방식인 LPG 연료의 액상분사방식을 채택하여 기존의 믹서방식의 연료공급시스템을 가진 LPG 엔진보다 고출력, 고효율, 저공해성을 추구하고자 하였다. 이를 위한 기초연구로서 먼저 단기통 연소엔진을 이용하여 대형엔진에 LPG 연료 적용 가능성, 액상분사 시스템을 포함한 여러 가지 연료공급방식에 따른 엔진의 성능파악, 대형엔진에 적합한 최적 선회비의 결정, 연료조성에 따른 엔진성능의 변화 등을 알아보았다. 실험결과, 대형엔진에 LPG 연료의 적용은 아무런 문제점이 없었으며 LPi 연료공급방식은 다른 방식에 비해서 10%정도의 체적효율 및 출력의 증가를 확인할 수 있었다. 최적의 선회비는 2.0 부근에서 형성되었고, 연료 조성은 프로판 대 부탄의 비율이 60 : 40에서도 정상적으로 운전됨을 확인하였다. 시제품 엔진의 경우, 과급방식의 KL6i 엔진을 개발하기 앞서 좀더 기술적 접근이 용이한 자연흡입방식의 K-1엔진의 개발이 선행되었으며 현재 개발 진행중인 K-1엔진의 성능평가 결과, 기존의 디젤엔진에 비해 출력성능이 20% 정도 향상됨을 확인할 수 있었다. 특히 대형차량에서 중요시 생각되는 저속토크 성능이 매우 우수한 것으로 파악되었다. 이러한 결과를 바탕으로 단기통 연소엔진에서 확인된 최적화된 연료조성과 선회비를 향후 K-1엔진에 적용할 예정이다. 최근 열린 가스학회 추계발표회와 LPG자동차세미나의 주요내용을 게재한다.

• 에너지공학
• /
• 제11권2호
• /
• pp.160-165
• /
• 2002

LPG 연료를 사용하는 대형 단기통엔진은 연소과정과 배기성능을 파악하기 위해서 설계.제작되었다. 실린더헤드와 피스톤 크라운은 LPG 연소를 위해서 변경되었다. 또한 플라이휠은 단기통엔진의 진동을 최소로 하기 위해서 제작되었다. 실험용 단기통엔진의 실린더내경과 행정은 각각 130mm와 140mm이다. 압축비는 피스톤 크라운 형상을 다르게 하여 8에서 9로 변경되었다. 본 연구를 위해서 제작된 단기통엔진은 1,000rpm에서 운전되었다. 본 연구의 주요 결론은 (1)제작된 엔진의 출력은 3가지 다른 압축비별로 당량비 1.0에서 최고를 나타낸다. (2) 압축비 증가에 따라서 출력이 약간 증간한다. (3) 최적 점화시기는 크랭크각으로 2에서 10까지 압축비의 증가와 함께 지각되어진다.

• 한국자동차공학회논문집
• /
• 제10권5호
• /
• pp.107-113
• /
• 2002

LPG has been well known as a clean alternative fuel for vehicles. Recently, several LPG engines for heavy duty vehicles have been developed, which can replace some diesel engines that are one of the main sources for air pollution in the urban area. Because cylinder bore of heavy duty LPG engine is larger than that of gasoline, the study of knock characteristics of LPG engine are needed. In this study, the knock characteristics were investigated with various engine speed, air excess ratios and LPG fuel compositions. Experimental results indicated that the Knock occurrence probability decreases with increasing engine speed and propane fraction of fuel. The Knock occurrence probability is highest at excess air ratio of 1 and decreases as the mixture strength became leaner.

• 기계와재료
• /
• 제12권2호통권44호
• /
• pp.32-39
• /
• 2000

• 대한기계학회논문집B
• /
• 제28권1호
• /
• pp.59-65
• /
• 2004

The configuration of intake port and piston is a dominant factor of inlet air flow and mixture formation in an engine cylinder, resepectively. This study has analyzed intake port and piston characteristics for swirl flow of a heavy-duty LPG engine. As an available technology to optimize intake port, the steady flow rig test has been applied for measuring swirl ratio and mean flow coefficient. And we measured the mean velocity and turbulence intensity of swirl flow under motoring condition in transparent engine cylinder by backward scattering LDV system. From these results, the piston and cylinder head with a good evaluated swirl flow characteristics were developed and adapted fur a 11L heavy-duty engine using the liquid phase LPG injection (LPLI) system. The obtained results are expected to be a fundamental data for developing intake port and piston.

• 한국정밀공학회지
• /
• 제19권11호
• /
• pp.146-159
• /
• 2002

An efficient method to predict the convection heat transfer coefficients on the top surface of the engine piston is proposed. The method is based on the inverse method of the thermal conduction problem and uses a numerical optimization technique. In the method, the heat transfer coefficients are numerically obtained so that the difference between analyzed temperatures from the finite element method and measured temperatures is minimized. The method can be effectively used to analyze the temperature distribution of engine pistons in case when application of prescribed-temperature boundary condition is not reasonable because of insufficient number of measured temperatures. A hollow sphere problem with an analytic solution is taken as a simple example and accuracy and efficiency is demonstrated. The method is applied to a practical large liquid petroleum gas(LPG) engine piston and the heat transfer coefficients on the top surface of the piston is successfully calculated. Resulting analyzed temperature favorably coincides with measured temperature.

• 한국가스학회:학술대회논문집
• /
• 한국가스학회 2000년도 추계학술발표회 논문집
• /
• pp.137-142
• /
• 2000

• 한국자동차공학회논문집
• /
• 제12권4호
• /
• pp.1-11
• /
• 2004

Combustion and fuel distribution characteristics of heavy duty engine with the liquid phase LPG injection(LPLI) were studied in a single cylinder engine, Swirl ratio were varied between 1.2, 2.3, and 3.4 following Ricardo swirl number(Rs) definition, Rs=2.3 showed the best results with lower cycle-by-cycle variation and shorter burning duration in the lean region while strong swirl(Rs=3.4) made these worse for combustion enhancement. Excessive swirl resulted in reverse effects due to high heat transfer and initial flame kernel quenching. Fuel injection timings were categorized with open valve injection(OVI) and closed valve injection(CVI). Open valve injection showed shorter combustion duration and extended lean limit. The formation of rich mixture in the spark plug vicinity was achieved by open valve injection. With higher swirl strength(Rs=3.4) and open valve injection, the cloud of fuel followed the flow direction and the radial air/fuel mixing was limited by strong swirl flow. It was expected that axial stratification was maintained with open-valve injection if the radial component of the swirling motion was stronger than the axial components. The axial fuel stratification and concentration were sensitive to fuel injection timing in case of Rs=3.4 while those were relatively independent of the injection timing in case of Rs=2.3.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권3호
• /
• pp.538-550
• /
• 2004

The convection heat transfer coefficients on the top surface of a large liquid petroleum liquid injection(LPLi) engine piston with the oil gallery are analyzed by solving an inverse thermal conduction problem. The heat transfer coefficients are numerically found so that the difference between analyzed temperatures from the finite element method and measured temperatures is minimized. Using the resulting heat transfer coefficients as the boundary condition, temperature of a large LPLi engine piston is analyzed. With varying cooling water temperature, temperature, stress, and thermal expansion of the piston are analyzed and evaluated.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2006년도 정기 학술대회 논문집
• /
• pp.820-827
• /
• 2006

The convection heat transfer coefficients on the top surface of a large liquid petroleum liquid injection(LPLi) engine piston are analyzed by solving an inverse thermal conduction problem. The heat transfer coefficients are numerically found so that the difference between analyzed temperatures from the finite element method and measured temperatures is minimized. Using the resulting heat transfer coefficients as the boundary condition, temperature of a large LPLi engine piston is analyzed.