• Journal of the Korea institute for structural maintenance and inspection
• /
• v.15 no.2
• /
• pp.61-69
• /
• 2011

Fiber Reinforced Plastic (FRP) sheets have been widely used to retrofit and rehabilitate RC structures, while in case of retrofitting steel structures, there are no codes and researches. It stems from configuration of member and characteristics of bonding behavior. This study focused on the static behavior of steel beams reinforcement by AFRP sheets. The main objective of the experimental programme was the evaluation of the force transfer mechanism, the increment of the beam load carrying capacity and the bending stiffness. A bending test was conducted on a H-shaped steel beam, with aramid FRP sheets bonded to its flanges. The mid-span deflection and the strain from three points along AFRP sheets were recorded Test results exhibit that the increment of the load-carrying capacity with reference to a mid-span deflection level of 15 mm(1/125mm of the clear span) was equal to 9.4% and for the two layers case, an elastic stiffness increment is slightly higher than one layer case.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.1
• /
• pp.81-89
• /
• 2018

Austenitic stainless steels have excellent corrosion resistance, durability and fire resistance. Especially, since STS304L among austenitic types is a low-carbon variation of STS304 and has excellent intergranular corrosion resistance, it can often be used under the welded condition without heat treatment after field welding. This paper investigated ultimate behaviors such as ultimate strength and weld metal fracture mechanism of STS304L fillet-welded connections with TIG(tungsten inert gas) welding through test results. Main variables of specimens are weld length and welding direction against loading. Fracture of specimens are classified into three modes(tensile fracture, shear fracture and block shear fracture). Ultimate strengths were compared according to the welding direction and weld length and TFW series with transverse fillet weld had the highest strength compared with other types(LFW series with longitudinal fillet weld and FW series with all round weld). It is known that current design specifications such as KBC 2016 and AISC2010 underestimated the strength of TFW and LFW specimens and provided unconservative estimates for FW specimens. Finally, strength equations were proposed considering material properties of STS 304L material.

• Journal of Korean Ophthalmic Optics Society
• /
• v.19 no.4
• /
• pp.493-498
• /
• 2014

Purpose: This study utilized the Geographic Information System (GIS) which is one of the representative methods for describing visual distribution, to show the distribution of visions of middle and high school students in 16 cities or provinces in Korea. Method: The data of National Health and Nutrition Examination Survey (NHANES) were analysed from 2009 to 2011 and designed a population-based cross-sectional study. The subjects were total 1,049 students at the age of 13 to 18 and uncorrected vision was provided. Male subjects were 549 (52.3%) and female subjects were 500 (47.7%). Subjects were divided into 16 cities or provinces and average vision of regions were analysed. the differentials of vision among the regions were analysed by as a spatial analysis method. Results: The average uncorrected vision were significant difference by sex (p=0.001). However male and female student groups' average vision indicated no statistically significant difference by region in those 16 cities and provinces. In order to show the differentials of middle and high school students' vision by region with a visual distribution method, the GIS was utilized for mapping. Conclusions: The differentials of vision among regions by GIS provide a visually effective distribution map.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.6
• /
• pp.147-154
• /
• 2014

The cable damages of the bridge structures induce very important impact on the structural safety, which implies the close monitoring of the cable damage is required to secure sustained safety of the bridges. Most usual available maintenance techniques are based on the monitoring the change of the natural frequency of the structures by damages. However, existing method are based on vibration method to calculate lateral vibration and system identification can calculate the axial stiffness using sensitivity equation by trial error method. But the frequency study by the longitudinal movement need because of the sag effect in system identification. This study proposes a new method to investigate the damage magnitudes and status. The method improves the accuracies in the magnitudes and status of damages by adopting the natural frequency of longitudinal movement. The study results have been validated by comparing them with the approximate solution of FEM. Thus, the relationship of cable damage and frequency appear with relation that the severe damage has the little frequency. If we know the real frequency we can estimate the cable damage severity using this relationship. This method can be possible the efficient management of the cable damage.

• Sijohaknonchong
• /
• v.19 no.1
• /
• pp.235-260
• /
• 2003

Recently, I presented Gagok(歌曲) Collection Yeong-eon永言 to learned circles. Yeong-eon is very similar to Yukdang-version六堂本 CheongGuYeongeon靑丘永言. Compared with Cheong- Yuk, it is the same age or little bit early time of Cheong-Yuk in culture Icon. This paper paid attention to the considerable difference between Yeong-eon and Cheong-Yuk in the way of the distribution of Yisakdaeyap二數大 葉's Woo mode羽調 and Ke-myeon mode界面調. There was the way of gathering ‘real name’+‘namelessness’ in Yisakdaeyap, which is the feature of the 18th century Gagok Collection. I found this way just put on the 19th century Gagok Collection way which is the distribution of Yisakdaeyap's 'Woo mode and Ke-myeon mode' in CheongYuk. Then I proved in this paper that the way of gathering Yisakdaeyap in Cheong Yuk didn't correspond to an actual singing in the early 19th century when 'Woo mode and Ke-myeon mode' was fixed. In case of Yeong-eon, however, it was not written any writers' names at all, when it was researched retroactively, I knew it was distributed evenly both the works of 'real name' and 'namelessness' in Yisakdaeyaps 'Woo mode and Ke-myeon mode'. Consequently, I found Yeong-eon is the good Gagok Collection for an actual singing at that time. In addition, there was discord in the mode or key distribution among many Gagok Collections. I found this issue of the application had kept on make Gagok Collections edit during 2 centuries. Because the actual Gagok enjoyment in the specific time is connected the way of the mode application directly.

• Journal of the Korean Vacuum Society
• /
• v.21 no.4
• /
• pp.199-204
• /
• 2012

$SF_6$ gas is widely used for dry etching process of semiconductor and display fabrication process. But $SF_6$ gas is considered for typical greenhouse gas for global warming. So it is necessary to research relating to $SF_6$ alternatives reducing greenhouse effect in semiconductor and display. $C_3F_6$ gas is one of the promising candidates for it. We studied about etch characteristics by performing Reactive Ion Etching process of dry etching and reduced gas element exhausted on etching process using absorbent Zeolite 5A. $Si_3N_4$ thin film was deposited to 500 nm with Plasma Enhanced Chemical Vapor Deposition and we performed Reactive Ion Etching process after patterning through photolithography process. It was observed that the etch rate and the etched surface of $Si_3N_4$ thin film with Scanning Electron Microscope pictures. And we measured and compared the exhausted gas before and after the absorbent using Gas Chromatograph-Mass Spectrophotometry.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 1998.11a
• /
• pp.19-20
• /
• 1998

오버레이용접에 의한 표면개질기술(Weld Surfacing or Hardfacing Technology)은 내식성, 내 마모성, 또는 내열성을 갖는 합금의 용접재료를 모재 표면에 균일하게 용착(오버레이:Ovedayer)시킴으로써 목적하는 재료의 표면성질을 향상시키는 표면처리의 한 방법이으로써 1922년 Stoody가 Steel Tube에 Cr합금 분말을 충진한 용접봉을 제조하여 석유시추용 회전드릴의 선단 표면을 오버 레이 용접시켜 내마모성을 획기적으로 개선시킴으로써 이루어 졌다. 초기 오버레이 용접기술은 발전설비I 제철설비I 시벤트설비, 그리고 제지설비 등 주로 설비 부품들의 표면부 내마모성을 개선시키는 방향으로 주로 연구 개발이 이루어졌으나, 기술개발의 진전으로 탈황설비 둥의 표면부 내식성 향상, 연속주조롤 표면부의 내산화성, 내열피로성, 내마모 성 향상 둥을 위해 점차 산업전반에 널리 이용되고 있으며, 설비의 고도화 및 장수명화가 요구되 면서 본 기술의 중요성 또한 점차 부각되고 있다. 그림 1은 연강의 모재 위에 셀프쉴드플럭스코어드와이어(Self-Shield Flux Cored Wire:SS-FCW, 이하 55-FCW라 기술함)를 사용하여 오버레이 용접올 하는 장면을 도식적으로 나 타낸 것이다. 모재와 전극재인 용접봉(S5-FCW) 사이에서 아크가 발생되고, 아크열에 의해서 용접 봉 및 모재 일부가 용융되면서 모재 표면에 새로운 오버레이 표면층이 형성된다. 통상 오버레이 층의 1층 두께는 2-6mm 내외이며, 단층 혹은 다충 오버레이를 자유롭게 실시한다. 오버레이층의 물성은 아크열에 의한 모재로의 용입정도에 따라 1층부에서는 모재의 영향을 크게 받지만 오버레 이충 수가 증가된 3층부에서 부터는 전적으로 용접봉의 성분에 좌우된다. 사진 1은 연강(55-41)의 모재위에 크롬탄화물이 다량 함유된 고크롬 탄화물형 내마모재가 오버 레이된 내마모 복합강판 (wear plate)의 단면 미세조직 사진으로써 모재부와 오버레이충을 함께 보여주고 있다. 모재와 오버레이 충간의 경계면은 모재 일부가 용융된 후 웅고하면서 형성됨으로 인해서 도금이나 용사층과는 달리 매우 견고하게 결합되어 있다. 따라서 계면부의 탈락이라는 문 제점은 거의 없어 심한 응력을 받는 기계구조물 및 부품에도 본 기술은 널리 적용되고 있다. 그리고 사진 1에서 알 수 있는 바와 같이 모재와는 전혀 상이한 재료를 자유로이 선택하여 표면 유효층 일부만 오버레이시키며I 주조 및 단조가 불가능한 재료까지도 표면부에 오버레이 시킴으로 서 부품 및 설비의 제조에 있어 재료비의 절감과 제품의 수명이 획기적으로 개선될 수 있다. 그리고 최근에는 도금 빛 용사 둥과 같은 표면처리를 할 경우임의 소재 표면에 도금 및 용 사에 용이한 재료를 오버레이용접시킨 후 표면처리를 함으로써 보다 고품질의 표면층을 얻기위한 시도가 이루어지고 있다. 따라서 국내, 외의 오버레이 용접기술의 적용현황 및 대표적인 적용사례, 오버레이 용접기술 및 용접재료의 개발현황 둥을 중심으로 살펴봄으로서 아직 국내에서는 널리 알려지지 않은 본 기 술의 활용을 넓이고자 한다.

• Journal of the Korean Geotechnical Society
• /
• v.34 no.2
• /
• pp.55-63
• /
• 2018

In order to support the load of the train with enough stiffness, a study on an effective method for the characterization of the stiffness of the compacted subgrade is required. In this study, the crosshole-type dynamic cone penetrometer (CDCP) is used for the stiffness characterization of the subgrade along the depth. For the application of the CDCP test, three points of compacted subgrades are selected as the study sites. For the study sites, CDCP test, in-situ density test, and light falling weight deflectometer (LFWD) test are conducted. As the results of CDCP tests, shear wave velocity profiles are obtained by using the travel times and the travel distances of the shear waves along the depth. In addition, maximum shear modulus ($G_{max}$) profiles are estimated by using the density of the subgrades and the shear wave velocity profiles. The averaged maximum shear moduli at each testing point are highly correlated with the dynamic deflection moduli ($E_{vd}$) determined by LFWD tests. Therefore, a reliable stiffness characterization of the subgrade can be conducted by using CDCP tests. In addition, because CDCP characterizes the stiffness of the subgrade along the depth rather than a representative value, CDCP test may be effectively used for the stiffness characterization of the subgrade.

• Economic and Environmental Geology
• /
• v.51 no.6
• /
• pp.579-587
• /
• 2018

Chungnam Basin has been known as one of the largest Mesozoic basins in Korea, filled mainly with so-called Daedong Supergroup. The basin has evolved as the Early to Middle Jurassic intra-arc volcano-sedimentary basin developed on top of the Late Triassic to Early Jurassic post-collisional basin in this area, recording evolutionary history of the Mesozoic tectonics in the southwestern Korean Peninsula. This study carries out the geometric interpretations of the Seongjuri syncline and its surroundings in the central part of the Chungnam Basin, based on detailed structural field survey. Based on its doubly-plunging fold geometry, the Seongjuri syncline could be subdivided into the southwestern and northeastern domains. On the down-plunge profiles of the southwestern domain of the Seongjuri syncline as well as the underlying Okma fold, the Okma fault shows typical geometry of a basement-involved reverse fault that propagated up to the sedimentary cover. The profiles illustrate that the Seongjuri syncline occurs in front of the tip of the Okma fault, likely implying its origin as a part of the fault-related fold system. The result of this study will provide better insight into the structural interpretation of the Chungnam Basin, and will further provide useful information for the Mesozoic orgenic events of the southwestern Korean Peninsula.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.9
• /
• pp.481-487
• /
• 2019

Additive manufacturing is a state-of-the-art manufacturing process technology in which three-dimensional structures are fabricated by laminating two-dimensional sections of a structure using various materials such as plastic, ceramics, and metals. The additive manufacturing technology has the advantage of high design freedom, while the surface property (roughness) of the finished product varies depending on the process conditions, which necessitates performing a post-process after the products are manufactured. In this study, the surface roughness of a structure made of polyamide 12, which was manufactured by SLS (Selective Laser Sintering) and MJF (Multi Jet Fusion) process was compared. The processing condition was classified by the building orientation of structure as 0, 45, and 90 degrees, which is the angle between the analytical surface and the horizontal plane of the fabrication platform. Structures with a hole of various diameters ranging from 1mm to 10mm were manufactured and the hole characteristics (ratio of hole depth to diameter) and results of the specimens were compared. As a result of the surface characteristics analysis, the surface roughness value of the specimens manufactured with a building orientation of $45^{\circ}$ was the highest in both technologies. In the case of the through-hole structure fabrication, the shape was maintained with 5mm and 10mm diameter holes regardless of the building orientation, although the hole forming was difficult for the smaller holes.