• Applied Chemistry for Engineering
• /
• v.30 no.6
• /
• pp.659-666
• /
• 2019

Proton exchange membrane fuel cells (PEMFCs) generate electricity by electrochemical reactions of hydrogen and oxygen. PEMFCs are expected to alternate electric power generator using fossil fuels with various advantages of high power density, low operating temperature, and environmental-friendly products. PEMFCs have widely been used in a number of applications such as fuel cell vehicles (FCVs) and stationary fuel cell systems. However, there are remaining technical issues, particularly the long-term durability of each part of fuel cells. Degradation of a carbon supported-platinum catalyst in the anode and cathode follows various mechanistic origins in different fuel cell operating conditions, and thus accelerated stress test (AST) is suggested to evaluate the durability of electrocatalyst. In this article, comparable protocols of the AST durability test are intensively explained.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.4
• /
• pp.5-21
• /
• 2012

In our country, in the case of traditional design of pile foundations, only a design depending on end bearing has been performed. However, through the load transfer measurement data that have been carried out for in-situ piles, it was known that skin frictional force was mobilized greatly. In this study, through the analysis of the load transfer test cases of driven steel pipe piles and large-diameter drilled shafts, load bearing aspects of pile foundation depending on pile construction methods and pile load test methods were established. The average sharing ratios of skin frictional force were independent of pile types, pile load test methods, relative pile lengths, pile diameters and soil types. Because the average sharing ratios were over 50%, the case pile foundations mostly behaved as a friction pile and the extremely partial case pile foundation behaved as a combined load bearing pile.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.3
• /
• pp.353-359
• /
• 2010

For achieving economical fuel consumption, an increase in the load bearing capacity, and for environmental conservation, there is a constant demand for lightweight frames of commercial vehicles used in the transportation industry. In this study, a structural analysis of the frame of a heavy flat-bed trailer was performed to determine the optimal design of a new lightweight frame made of high-strength steel. To identify the key design parameters of the trailer frame, Taguchi's orthogonal array was used in the experiments. Using ANSYS, a commercial FEA program, the frame structure was optimized with respect to stress, deflection, and torsional stiffness by performing stress and vibration analyses. A physical model of the trailer was also built to verify the validity of the numerical analyses. Finally, an on-road fatigue test of the new lightweight frame made of the high-strength steel, ATOS80, was performed to confirm the durability of the new design.

• Plant Journal
• /
• v.14 no.2
• /
• pp.45-50
• /
• 2018

Nuclear safety law's amendment caused many problems to use radiography testing(RT). Phased array ultrasonic testing(PAUT) was adapted instead of RT for NDE of welding points in boiler tubes these days. Unfortunately, PAUT doesn't give us the discrimination characteristics about flaws distinction and flaws size clearly. In this thesis, the distinction characteristics of flaw types and the detection characteristics of flaw size using PAUT of welding points in boiler tubes were analyzed. It was concluded that PAUT can distinguish between planar flaws and rounded flaws, but it is hard to tell apart the types of flaw respectively. We paid attention to the discrimination of flaws size because PAUT tends to underestimate the flaw size of porosity and underestimate or overestimate the flaw size of porosity.

• Membrane Journal
• /
• v.8 no.4
• /
• pp.228-234
• /
• 1998

Among various water contaminents, organic compounds like phenol are difficult to be removed or destroyed by conventional methods under the unusual discharge conditions. The separation of phenol from aqueous solution has been carried out by several methods recently: absorption by an activated carbon, solvent extraction and liquid membrane technology. The liquid membrane based on water-oil emulsification has been tested as an alternative technology of the conventional technology. In this work, tri-n-butyl phosphate(TBP) and liquid polymers were examined as a liquid membrane in the supported liquid membrane(SLM). The feed concentration of phenol was varied and various types of liquid membranes were used to examine their effects on separation of phenol. It was found that TBP, polypropylene glycol 4000(PPG 4000) and polybutytene glycol 500(PBG 500) were proper carriers because mass transfer rates through them were much higher than or similar to that through methyl isobutyl ketone(MIBK) which was used as a conventional solvent in a solvent extraction process.

• The Journal of Engineering Geology
• /
• v.16 no.4 s.50
• /
• pp.381-392
• /
• 2006

The passive surface wave survey using microtremor is conducted in areas of crystalline rock basements to obtain average shear-wave velocity structures to 30 m deep (Vs30), on which the earthquake-resistant design standard is based. Test data were recorded at two sites with triangular and L-shaped arrays for 4 seconds with an sampling interval of 2 ms. The microtremor recorded at a site were analysed using the spatial autocorrelation method to obtain phase-velocity spectra and effects of major factors such as size and shape of away and number of record and receiver were examined. At the other site, shear-wave velocities were derived from VSP and microtremor data separately. The results from these two methods agree to each other reasonably well, indicating that the microtremor method can be an effective geophysical tool to measure Vs30.

• Industry Promotion Research
• /
• v.6 no.4
• /
• pp.1-9
• /
• 2021

The purpose of this study is to manufacture lightweight aggregates for recycling water treatment sludge, to identify the physical properties of the aggregates, and present a method of utilizing the manufactured lightweight aggregates. The chemical composition and thermal properties were examined via a raw materials analysis. The aggregate examined here was fired by the rapid sintering method and the single-particle density and water absorption rate were measured. Water treatment sludge has high ignition loss and high fire resistance. When 30wt% of purified sludge was added, the single-particle density of the aggregates was in the range of 0.8~1.2g/cm³ at a temperature of 1,150~1,200℃. At temperatures of 1200℃ or higher, ultra-light aggregates having a single-particle density of 0.8 or less could be produced. When applied to concrete by replacing the general aggregate in the concrete, a specimen having strength values of 200 to 450 kgf/cm² on 28 days was obtained, and when applied as a filter material, the performance was equal to or higher than that of ordinary sand.

• Journal of Soil and Groundwater Environment
• /
• v.8 no.2
• /
• pp.62-69
• /
• 2003

The aim of research is the evaluation of the $Cr^{6+}$ emission features of the liquid injection through emission experiments in varying conditions, based on a field-mixing ratio. The results showed that the content of $Cr^{6+}$ content in cement measured had an Ordinary Potland Cement (OPC) of 25.3 mg/kg, which constitute the largest portion among the other materials. Likewise, the emission experiment of homo-gel and sand-gel generally satisfied the standard of KSLT (Korea Standard Leaching Test) in waste of 1.5 mg/L, but in case of the standard of KSLT in soil the emission of OPC $Cr^{6+}$ of 4.85 mg/kg. These conditions is a little exceeded the criteria in the ‘Ga’ area in terms of Korea Soil Environmental Preservation Law. In addition, results generated by the mock-up injection facilities revealed that $Cr^{6+}$ emission increased as Water/Cement and injection pressure increased. At injection pressure higher than 4 kg/㎤, $Cr^{6+}$ emission exceeded the water preservation standard of 0.5 mg/L. Similarly, a pattern experiment of C $r^{6+}$ emission according to pH was conducted, in order to evaluate the $Cr^{6+}$ emission features of grout materials in leachate below pH 5 such as pH 4 acid rain or landfill. Results show that $Cr^{6+}$ emission dramatically increased in high acidic or basic state. It indicates that $Cr^{6+}$ emission will probably increase in an environment where grout materials are injected. On the other hand, concentration of leachate was determined in areas where grout materials are used. The results show that the concentration of emission in an ultra purity condition does not manifest intensity, and is affected in the OPC>MC>SC order. It means that the pollutants or $Cr^{6+}$ emission increases with decreasing concentration. As such, $Cr^{6+}$ emission will probably exceed the countermeasure criteria according to the types of gout materials. Similarly, high pressure or injection will cause increased $Cr^{6+}$ emission. Therefore, the selection of materials or mixing ratio should be considered in general as well as according to specific industries, based on the strength and pH of $Cr^{6+}$ emission.

• The Journal of the Korean life insurance medical association
• /
• v.25
• /
• pp.49-62
• /
• 2006

생명공학의 시대로 일컬어 지고 있는 오늘날, 재생의학 분야에서는 난치성 질환 치료를 목적으로 활발한 연구가 진행되고 있다. 특히, 줄기세포를 이용한 세포 대체치료 관련 연구는 최근 국내 황우석 박사의 체세포 핵이식 배아세포주 확립에 이르기 까지 괄목할 만한 발전을 보여 주고 있다. 이와 관련해 생명보험산업에 적잖은 파장이 예상되며, 생명보험사 내부적으로 기존에 판매된 상품의 사차손 관리와 함께 급속도로 발전하는 줄기세포 연구에 직접적으로 대응하는 상품개발, 언더라이팅, 지급 심사 등 보험사 내외에서의 전방위적인 변화가 필요하다는 문제 제기가 있다. 줄기세포란 조직 분화 과정에서 볼 수 있는 세포이며 근육 뼈 뇌 피부 등 신체의 어떤 기관으로도 전환할 수 있는 만능세포로서, 간 폐 심장 등 구체적 장기를 형성하기 이전에 분화를 멈출 배아 단계의 세포를 말한다. 한편, 성체줄기세포는 조직이나 기관의 분화된 세포들 사이에서 발견되는 미분화 세포로써, 자기 스스로 증식할 수 있으며, 조직이나 기관의 특수한 기능을 가지고 있는 세포로 분화할 수 있는 능력을 가진 신체줄기세포를 말한다. 배아줄기세포와 생체줄기세포를 통한 장기이식 등 난치병 정복은 윤리적, 사회적으로 많은 논란이 예상되며, 기술적으로도 해결해야 할 문제점들이 산적해 있기 때문에 아직은 요원한 것이 사실이다. 현재 유럽 대부분의 나라와 미국에서는 인간 배아의 복제가 금지되어 있으며, 일본 정부는 연구용 배아 복제를 제한적으로 허용하고 있다. 하지만, 우리 나라의 경우 2005년 1월에 '생명윤리 및 안전에 관한 법'이 발효되었지만 정부는 관련 부작용에 대한 깊은 고찰 없이 전폭적인 지원들 약속하고 있는 실정이다. 줄기세포 연구의 발달로 인해 인류가 난치병 치료의 첫 장을 열었다고 하더라도 그 영향이 당장 보험사에 미친다고 할 수는 없다. 왜냐하면 앞으로 이러한 신기술이 실제 의료행위에 적용되기 위해서는 여러 단계의 안정화 작업과 임상시험이 필요한데 이러한 작업이 기술적으로 어렵고 그 시간도 만만치 않게 걸리기 때문이다. 또한, 보험사의 보장은 크게 사망/수술/입원/암/기타보장으로 구별할 수 있는데, 줄기세포 연구의 발달과 관련이 있는 보장이 제한되어 있어 보험사에 미치는 영향이 당장 우려할 만한 수준이라 할 수 없다. 하지만 만약 치료용 줄기세포 배양으로 인한 장기 기관의 이식이나 손상세포의 대체 등과 같은 의학신기술의 예상 외로 급격하게 발전한다면 보험사의 Risk 관리에 상당한 저해요인으로 작용할 것으로 판단된다. 특히 진단 입원 수술로 대표되는 생존보장에 대한 사차 Risk 및 사차손의 급증이나 역선택 증가는 보험사의 경영수지 악화를 유발하여 보험산업 전반에 위험으로 작용할 수도 있다. 따라서, 장기적인 안목으로 업계 공동의 대응이 필요하고, 각 사에서도 상품개발, 언더라이팅, 지급심사 간의 긴밀한 협조가 요구된다. 생명보험산업의 Risk 관리는 기존의 시장환경에 영향을 받는 비차, 이차중심에서 보험회사가 어느 정도 관리를 통해 적정규모를 유지할 수 있는 사차로 그 중심축이 이동하고 있다. 보험산업이 계속 활력을 갖고 성장하기 위해서는 체계적인 Risk나 관리가 핵심일 것이며, 보험사의 사차 Risk의 중요성이 더욱 커져 가고 있는 현실에서 거시적으로 의학신기술 발달 등 위험요인에 대해 미리 분석하고 이에 대한 대비책 마련이 필요할 것으로 판단된다.

• Korean Chemical Engineering Research
• /
• v.54 no.6
• /
• pp.854-862
• /
• 2016

As the demand for a clean energy to replace fossil fuel being depleted increases, hydrogen energy is considered as a promising candidate for future energy source. Water electrolysis which produces hydrogen has high energy efficiency and stability but still has a large overpotential for oxygen evolution reaction (OER). In this study, $Co_3O_4$ catalysts with different morphology were prepared by spray pyrolysis from solutions which contain Co precursor and various organic additives (urea, sucrose, and citric acid), followed by post heat treatment. For the catalysts synthesized, X-ray diffraction (XRD) measurements were performed to identify their crystal structure. Morphology and surface shape of the catalysts were observed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Surface area and pore volume were examined by nitrogen adsortpion & desorption tests and X-ray photoelectron spectroscopy (XPS) was conducted to confirm nitrogen doping. Linear sweep voltammetry (LSV) was carried out to investigate OER activity of $Co_3O_4$ catalysts. As a result, bare-$Co_3O_4$ which has high surface area and small particle size determined by spray pyrolysis showed high activity toward OER.