• Journal of Korean Society on Water Environment
• /
• v.21 no.6
• /
• pp.669-675
• /
• 2005

Biological nitrate removal from groundwater was investigated in the biofilters packed with both gravel/sand and plastic media. Removal of particles and turbidity were also investigated in the 2-stage biofilter system consisted of biofilter and subsequent sand filter. In the single biofilter packed with gravel and sand, nitrate removal efficiency was dropped with the increase of filtration velocity and furthermore, nitrite concentration increased up to 3.2 mg-N/L at 60 m/day. Denitrification rate at the bottom layer below 25 cm was faster 8 times than upper layer in the up-flow biofilter. Nitrite build-up, due to the deficiency of organic electron donors, occurred at the upper layer of bed. Besides DO concentration and organic carbon, contact time in media was the main factor for nitrate removal in a biofilter. The most of the effluent particles from biofilter was in the range from 0.5 to $2.0{\mu}m$, which resulted in high turbidity of 1.8 NTU. However, sand filter followed by biofilter efficiently performed the removal of particles and turbidity, which could reduce the turbidity of final filtrate below 0.5 NTU. Influent nitrate was removed completely in the 2-stage biofilter and no nitrite was detected.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.15 no.2
• /
• pp.45-50
• /
• 2005

During oxidation process, several type of defects are formed on the surface of the silicon crystal which was damaged mechanically before oxidation. As the size of abrasive particle increases multiple dislocation loops are produced favorably over oxidation-induced stacking faults, which are dominantly produced when ground with finer abrasive particle. These defects are not related with the crystal growth process like Czochralski or directional solidification. During directional solidification process, twins and stacking faults are the two major defects observed in the bulk of the silicon crystal. On the other hand, slip dislocations produced by the thermal stress are not observed. Thus, not only in single crystalline silicon crystal but also in multi-crystalline silicon, extrinsic gettering process with programmed production of surface defects might be highly applicable to silicon wafers for purification.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.7
• /
• pp.171-181
• /
• 2004

This study was conducted to explore the tensile strength models in granular soil at the full range of unsaturated state. Direct tension experiments were carried out with a newly developed direct tension technique. The measured experimental data were compared with theoretical models developed by Rumpf and Schubert for monosized ideal particulate solids at the unsaturated state. To do this, the soil-water characteristic curve obtained from a suction-saturation experiment was used to define the unsaturation state and the negative pore water pressure with different water content levels, which are important factors in theoretical tensile strength models. The nonlinear behavior of the tensile strength for unsaturated granular soil at the pendular state is appropriately simulated with Rumpf's model. For the funicular and capillary states, the predicted trend by Schubert's model is properly matched with the experimental data: tensile strength steadily increases and reaches a maximum value and then decreases until it reaches zero. This comparison supports the concept that the tensile strength of unsaturated real granular soil can be approximately simulated with theoretical models.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.2
• /
• pp.432-445
• /
• 1994

From a theoretical analysis point of view, the 2-stage precipitator is decomposed into two units: charging cell and collecting cell. Collection efficiency predictions of the two-stage parallel-plate electrostatic precipitator have been performed theoretically incorporating with the charging and the collecting cells. Particle trajectorise passing the charging cell have been modeled as a simple one. Particle charge distribution at the outlet of the charging cell is calculated through integration of the present unipolar combined charging rate along the entire particle trajectory, and average charge of particles at the outlet of the charging cell is obtained from the particle charge distribution. As for the collecting cell, the diminution of particle concentration along the longitudinal direction of the collecting cell is investigated considering the conventional Deutsch's theory and the laminar theory. One should note that the collection efficiency formula derived is based on monodisperse aerosols. It has been confirmed through the analysis that predictions of particle charge by applying White's unipolar diffusion charging theory overpredict actual cases in the continuum regime, while predictions by Fuch's unipolar diffusion charging theory indicate the reasonable result in the same regime. Theoretical predictions of collection efficiency are also compared with the available experimental results. Comparisons show that the experimental results are consistently located in the collection efficiency region bounded by the two limits, the Deutsch and the laminar collection efficiencies. Finally design parameters of the 2-stage electrostatic precipitator have been investigated systematically through the one-variable-at-a-time method in terms of collection efficiency. Applied voltages on the corona wire of the charging cell and the plate of the collecting cell, and the average air velocity have been selected as the design parameters.

• Applied Chemistry for Engineering
• /
• v.18 no.6
• /
• pp.552-556
• /
• 2007

In this study, noble metals (Pd, Ru, Ir) were supported to $TiO_2$ catalyst. In order to distribute metals uniformly, $H_2O-H_2$ pretreatment technique was used. Xylene, toluene, and MEK were used as reactants. The monometallic or bimetallic catalysts were prepared by the excess wetness impregnation method and were characterized by XRD, and XPS analysis. Pd-Ru, Pd-Ir bimetallic catalysts had multipoint active sites which improved the range of Pd metal state. Bimetallic catalysts had a higher conversion of VOCs than that of monometallic one. The effect of $H_2O-H_2$ pretreatment technique was the enhancement of uniform distribution of Pd particles and promotion of catalytic efficiency. In this study, addition of Ru and Ir metals to Pd promoted oxidation conversion of VOCs. In addition, $H_2O-H_2$ pretreatment promoted removal efficiency of VOCs on the $TiO_2$ support.

• Korean Chemical Engineering Research
• /
• v.50 no.1
• /
• pp.182-185
• /
• 2012

N-doped $TiO_2$nanotubes have been newly prepared by two stage sol-gel and strong-alkali hydrothermal process using $TiCl_4$ and hydrazine/ammonia aqueous solution as raw materials. These nanotubes revealed a well developed anatase crystalline phase and perfect nanotube morphology with the diameter around 10nm and the wall thickness below 3 nm. Also, they showed a superior visible light activity and yellowish color due to the light absorption redshifted by ~35 nm and ~25 nm compared to undoped $TiO_2$ nanotubes and anatase nanoparticles, respectively.

• Clean Technology
• /
• v.14 no.4
• /
• pp.256-264
• /
• 2008

In this study, using PBAST (poly(butylene adipate-co-succinate-co-terephthalate)) which was eco-friendly biodegradable aliphatic polyester, PBAST/PVA (poly(vinyl alcohol)) double-layered hollow microspheres were prepared with the water/oil/water multiple emulsion ($W_1/O/W_2$) method. The double-layered hollow microspheres were manufactured with the yield of 30.92% when the concentration of polymer PBAST in organic phase was 5 wt%, the concentration of PVA in inner aqueous phase was 5 wt%, the volume ratio of $W_1/O$ emulsion to outer aqueous phase was 1:4.5, and when co-surfactants that had large gap in HLB (hydrophile-lipophile balance) value were used. The bulk density of prepared hollow microsphere was 0.180 g/ml and particle size was $1.5{\sim}3\;{\mu}m$.

• Journal of Korea Water Resources Association
• /
• v.49 no.9
• /
• pp.741-748
• /
• 2016

Laboratory scale model was constructed for open-cut riverbed infiltration experiment and four kinds of media were selected, medium sand, sand, volcanic rock, and gravel, for the experiment. Hydraulic conductivity for each medium and flow rate from the collecting pipe with functional screen were estimated from the experiment. Modified hydraulic conductivity scenarios considering turbid water (30~50 NTU) were applied in Visual MODFLOW modeling to analyze the effects of turbid water on the flow rate. Twenty-two scenarios were generated considering prticles in turbid water and applied to each medium cases in MODFLOW modeling. The minimum error was occurred when the gravel medium had 20% less hydraulic conductivities for the third layer-depth from the top and clay particles in turbid water might play a role in adsorption process to the surface of volcanic rock (2~5 mm). For medium sand case the error was also quite small when the mediumhas 5% less hydraulic conductivities for the second layer-depth from the top.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.11 no.6
• /
• pp.290-296
• /
• 2001

Fin metal particles of uniform shape, narrow size distribution and high purity are increasingly needed for specific uses in high tech industrial applications. Polyol process for the preparation of monodispersed cobalt powders in micron size is described. In this process in inorganic precursor is reduced in liquid polyol under controlled conditions. The reducing agent is the polyol itself and reaction parameters such as the traction temperature, reaction time, addition of protective agent and concentration of the precursor are varied for controling particles size, shape and agglomeration of the metal particles. An optimum synthesis condition was achieved at E.G/DiE/G volume ratio 1:4,Co$(OH)_{2}$polyol molar ratio 0.08~0.32 reaction temperature $210^{\circ}C$, PVP/Co$(OH)_{2}$ molar ratio 0.4.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.77-77
• /
• 2008

금(Au)이나 은(Ag)과 같은 귀금속 물질로 형성된 금속 나노 구조체는 표면 플라즈몬 공진(Surface Plasmon Resonance, SPR) 현상과 이의 국부 환경(local environment) 변화에 대해 민감한 의존성으로 인하여 생화학적 센서로의 응용이 주목 받고 있다. 표면 플라즈몬 공진은 광 흡수와 광 산란을 수반하는데, 두 가지 특성 모두 분광학적 신호검출방식으로 센서에 응용가능하다. 이 중 광 산란을 이용하는 방식은 광원의 배경잡음 효과가 배제되기 때문에 단일 입자 검출에 유리하다. 광 흡수와 광 산란 특성은 금속 나노 구조체는 크기, 형상, 주변 매질, 물질의 선택에 따라서 영향을 받는다. 본 연구에서는 금 나노 디스크(nanodisc)의 형상에 따라서 여기 되는 표면 플라즈몬이 광 흡수와 광 산란 특성에 미치는 영향을 가시광과 근적외선 영역에 대해서 불연속 쌍극자 근사법(Discrete Dipole Approximation, DDA)을 이용하여 전사모사(simulation) 하였다. 금 나노 디스크의 형상과 플라즈몬 특성 간의 관계는 공명 파장과 산란 양자 거둠율(scattering quantum yield, $\eta$)을 이용하여 분석하였고, 센서로서의 응용을 가늠하기 위해 주변 매질의 굴절률을 조절하여 그에 따른 민감도(sensitivity )를 비교하였다. 나노 디스크의 모양이 판상에 가까워질수록 공명 파장은 적색 편이하였고 광 산란 효율과 민감도는 증가하는 현상이 나타났다. 또한, 산란 양자 거둠율은 증가하다가 완만하게 감소하는 경향이 나타났다.