• Agrochemical news magazine
• /
• v.25 no.2 s.195
• /
• pp.6-9
• /
• 2004

• Journal of the Korean Wood Science and Technology
• /
• v.30 no.2
• /
• pp.165-171
• /
• 2002

This study was to investigate the adhesion properties of fancy veneer and base panels and formaldehyde emission of wood-based floorings bonded with urea-melamine formaldehyde adhesives. We focused on stoichiometric mole ratio of reactive functional groups. The urea-melamine formaldehyde adhesives were made at twelve different formaldehyde/urea-melamine mole ratios. The interlaminated shear strength and formaldehyde emission of wood-based floorings bonded with selected adhesive among these adhesives were examined. The results showed that the bonding properties were high and the formaldehyde emission was low as the adhesive consisted of stoichiometric mole ratio of formaldehyde/urea-melamine. Interlaminated shear strengths of HDF(High Density Fiberboard) flooring were over 14 kgf/cm² at all mole ratios. At the mole ratio of 1.0, HDF flooring showed low value of formaldehyde emission of 953 mg/L. Interlaminated shear strengths of Plywood flooring were high, 14.02 kgf/cm² at mole ratio of 1.4. At the mole ratio of 1.0, Plywood flooring showed low value of formaldehyde emission of 0.26 mg/L.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.5
• /
• pp.559-571
• /
• 2017

This study was conducted to determine the adhesive performances of plywoods affected by layering direction and the amounts of thermoplastic films. The face and back layers of veneer were hardwood species (Mixed light hardwood) and core layer veneer was radiata pine (Pinus radiata D. Don). Thermoplastic film used as adhesive were polypropylene (PP) film and polyethylene (PE) film. Thermal analysis and tensile strength were investigated on each films. As a result, the melting temperature of PP and PE films were $163.4^{\circ}C$ and $109.7^{\circ}C$, respectively, and the crystallization temperature were $98.9^{\circ}C$ and $93.6^{\circ}C$, respectively. Tensile strength and elongation of each films appeared higher on the width direction than length direction. Considering the characteristics of the thermoplastic films, the test for the amount of film used was carried out by layering film to the target thickness on veneer. The effecting of layering direction of film on plywood manufacturing was conducted by laminating in the length and width directions of the film according to the grain direction of veneer. Tensile-shear strength of plywood in wet condition was satisfied with the quality standard (0.7 MPa) of KS F 3101 when the film was used over 0.05 mm of PP film and over 0.10 mm of PE film. Tensile-shear strength of plywood after cyclic boiling exceeded the KS standard when PP film was used 0.20 mm thickness. Furthermore, higher bonding strength was observed on a plywood made with width direction of film according to grain direction of veneer than that of length direction of film. Based on microscopic analysis of the surface and bonding line of plywood, interlocking between veneers by penetration of a thermoplastic film into inner and cracks were observed.

• Journal of the Korean Wood Science and Technology
• /
• v.16 no.3
• /
• pp.65-71
• /
• 1988

캐나다가 미국산 활엽수재의 가장 큰 수입국이며 수입된 일부 제재목과 수입원목으로 제조된 단판중 일부는 유럽으로 재 수출되고 있다. 수입 물량적인면에서 캐나다는 다른 국가와의 격차는 좁혀지더라도 미국산 활엽수재의 제1위 수입국의 위치를 당분간 유지할 것이다. 유럽에서의 제재목 수요가 1973년부터 1983년간의 10년간에는 급진적으로 증가 되었지만 1984년에 는 갑자기 감소되었다. 이와같은 현상은 과거 유럽 전통가구에 소재(素材)를 많이 사용했지만 현재는 소재(素材)를 적게 사용하고 단판이나 인쇄한 종이를 붙인 파아티클 보오드(PB)를 더욱 많이 사용하고 있기 때문이다. 현재 유럽지역에서는 가구의 크기를 줄이거나 가구에 사용되는 원자재의 비용을 줄임으로 제품의 가격을 싸게하여 소비자에게 보다 경쟁력있는 가격으로 제품을 공급할려고 하고 있으며 활엽수재의 가격이 너무 비싸 가구제조업체들은 소재(素材)를 다른 것으로 대체하고 보다 값싼 수종을 모든 지역에서 찾고 있는 중이다. 태평양 연안국가에서의 미국산 활엽수재의 수입 물량은 계속 증가되어 미국산 활엽수 총 수출 물량의 약 23% 정도 된다. 자유중국과 일본에서 미국산 활엽수재를 가장 많이 수입하고 있다. 자유중국은 주로 수출용 가구부품및 가구에 사용되는 red oak와 white oak 가 주 수종이고 가구는 미국으로 재 수출하고 있다. 일본은 주로 black cherry, yellow poplar와 cotton wood를 수입하는데 수입량의 약 67%는 대패질한 건조 가공품이다. 자유중국에서와는 달리 일본에서의 미국산 활엽수의 용도는 일본산 활엽수의 대체수종으로 허용되고 있다. 앞으로 일본에서의 미국산 활엽수재의 수요는 일본 국내시장의 요인에 의해 좌우될 것인데 한정된 물량의 일본산 활엽수재와 온대 활엽수재의 요구에 영향을 받을 것이다.

• Journal of the Korean Wood Science and Technology
• /
• v.15 no.1
• /
• pp.22-55
• /
• 1987

This study was executed to offer the basic data needed to plywood industry in Korea for the future based on microscopic wood features as our previous paper reported by the macroscopic features. Microscopic wood characteristics for 50 species selected by the viewpoint of possible utility in future were examined and described by the species. Also, keys for the identification based on microscopic features were briefly prepared and presented by gymnosperm and angiospenn respectively.

• Journal of the Korea Furniture Society
• /
• v.23 no.4
• /
• pp.407-414
• /
• 2012

In order to develop the end use of cylindrical laminated veneer lumber (LVL) such as wooden crafts, the light resistance properties of natural dye-colored and finished cylindrical LVL was investigated. The study results were as follows; The cross section of LVL showed the higher light resistance than its tangential section, and the light resistance also increased with surface coated. On the other hand, LVL specimen were colored by 9 natural dyes of amur cork-tree etc., and the natural and apparent hue harmonized with wood was found after coating and light resistance test. Particularly, The dyes extracted from amur cork-tree, persimon and sappan wood showed orange color, reddish brown and red color respectively, giving an accenting effect to original wood color.

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.4
• /
• pp.344-350
• /
• 2011

In this study, LVLs of radiata pine were fabricated with non-preservative treated veneers, CuAz treated veneers, and ACQ treated veneers, using aqueous vinyl urethane adhesive and phenol modified resorcinol resin adhesive. Then density gradient, bonding strength, bending properties and decay resistance of LVLs were evaluated. As results, the cone-shaped and higher density gradient pattern was found in layer close to glueline. After cyclic water boiled test, the LVL bonded with aqueous vinyl urethane resin adhesive was delaminated in all layers or partly delaminated including check, chasm in glueline layer. In the case of LVL bonded with phenol modified resorcinol resin adhesive, despite slight cupping due to great glueline stress and vertical check between glueline layers, it was observed that the bonding strength to delamination was higher, owing to most absence of delamination through overall glueline. On the other hand, in the decay test, mass loss by brown rot fungi was greater than white rot fungi in LVL bonded with aqueous vinyl urethane resin adhesive. However, in LVL bonded with phenol modified resorcinol resin adhesive, the mass loss by brown rot fungi was slight and non-preservative treated LVL was low. The mass loss of preservative-treated LVL was 0 (zero), showing the high decay resistance effect.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.39 no.6
• /
• pp.789-799
• /
• 2019

The settlement hardly occurs in structures supported by pile foundation such as abutment, culvert but a cavity is formed in the lower part of a structure. As a result, soil discharged from the lateral ground to the cavity accelerates the settlement of the lateral ground of the structure, resulting in a larger settlement. Therefore, in order to prevent problems caused by cavity under the structure supported by pile foundation, soil Flow Protector (briefly called 'FLP'), which can be easily installed on the side of structure, was developed. In this study, an laboratory model test was carried out to prove the reduction effect of settlement and to estimate the optimal installation length of the FLP. As a result, the installation of the FLP reduced the settlement of the lateral ground and prevented the leakage of lateral ground soil into the cavity. If the stiffness of the FLP is small, the state or active earth pressure is generated in the upper part, which is not favorable for stability. But if the stiffness of the FLP is high enough, the passive earth pressure area is generated in the upper part, which will be advantageous for the stability. Also, the increased installation length of FLP is effective to reduce the settlement. And the ratio of the optimal length of the FLP to the box structure height (H = 250 mm) are flexible FLP 1.38, stiff FLP 0.73.

• Journal of the Korean Wood Science and Technology
• /
• v.34 no.6
• /
• pp.29-35
• /
• 2006

This stud y was conducted to investigate the bonding strength of plywood bonded with fatty acid-glycerol-pMDI adhesives with equivalent ratios of 1:1:2, 1:1:3, 1:1:4, 1:1:5, and 1:1:6. With veneer moisture contents of 0%, 3%, 5%, 8% and 15%, the bonding strengths exceeded the requirement of Korean plywood standard of $7.0kgf/cm^2$ with values of $13.7kgf/cm^2$, $11.6kgf/cm^2$, $11.2kgf/cm^2$, $9.8kgf/cm^2$, and $7.4kgf/cm^2$, respectively at fatty acid-glycerol-pMDI ratio of 1:1:2. With veneer moisture content of 30%, the bonding strengths exceeded th e requirement of Korean plywood standard of $7.0kgf/cm^2$, when fatty acid-glycerol-pMDI ratios were 1:6. Finally for satisfying the Korean plywood standard, the ratio of MDI in fatty acid-glycerol-pMDI should be increased with increasing of veneer moisture content.

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.6
• /
• pp.108-117
• /
• 2007

This research was performed to investigate the feasibility of bamboo as a raw material for the manufacture of plywood. Wood veneer-bamboo zephyr composite boards (WBCB) were manufactured using keruing (Dipterocarpus sp.) veneers and hachiku bamboo (Phyllostacbys nigra var. henonis Stapf) using various adhesives, and the effect of the method and amount of resin spread on the mechanical properties of the composites were investigated. The WBCB manufactured using polymeric isocyanate (PMDI) showed the best mechanical properties, followed by phenol-formaldehyde resin (PF), phenol-melamine-formaldehyde resin, urea-melamine-formaldehyde resin, and urea-formaldehyde resin. However, considering the operation feasibility as well as mechanical properties, PF resin proved to be the appropriate adhesive for the practical purpose. As the amount of resin spread increased, the mechanical properties of 5-ply WBCB with 12 mm thicknesses manufactured using PF resin tended to increase, and more failure occurred at the interface between veneer and bamboo zephyr than at the interface among bamboo zephyrs. This result suggests that penetration of resin into bamboo zephyr could be the important factor. In this research, the appropriate amount of resin amount was $320g/m^2$. 5-ply WBCBs were manufactured using various methods of resin spread but the effect of the methods on the mechanical properties showed no little difference, which meant that the method of resin spread could be chosen considering the manufacturing conditions and operation feasibility.