• Journal of the Korean Wood Science and Technology
• /
• v.40 no.6
• /
• pp.418-423
• /
• 2012

In order to develop the end use of cylindrical laminated veneer lumber (LVL) such as wooden crafts, the water proof-bonding strength, the resistance to abrasion and the surface hardness by painting the surface of LVL were investigated. The study results were as follows; The water proof-bonding strength through 5 cyclic test by boiling in water immersion and drying were favorable without delamination of glue line. Then the formulation of glue was resorcinol resin (100) to hardener of paraformaldehyde (5) by mixed weight percentage. The resistance to abrasion was relatively higher at cross section than tangential section. When tangential section of LVL was painted by UV protection oil, the resistance to abrasion was improved. In case of an cross section of LVL, the higher surface hardness appeared at larch core than radiata pine LVL. Also, in case of an tangential section of LVL, the higher surface hardness appeared at glue line than veneer side.

• Journal of the Korean Wood Science and Technology
• /
• v.17 no.1
• /
• pp.3-11
• /
• 1989

This study was carried out to investigate the physical and mechanical properties. durability of adhesive bond and paint film for the basic data which were required to determine the suitability as a raw material for furniture the laminated veneer lumber (LVL) with pitch pine (Pinus rigida Mill). The results obtained were as follows; 1) The proper pressing time for making the LVL was over 45 second per milimeter of LVL thickness. 2) The bending strength of the LVL was lower than that of the solid wood but the compressive strength of the LVL was similar to that of the solid wood. The strength increased with the decrease of veneer thickness. 3) The impact bending absorbed energy of the LVL was 0 to 0.3 kg.m/$cm^2$ in the direction of parallel to the grain. The energy of the LVL was lower than that of the solid wood (0.68 kg.m/$cm^2$). 4) In warm water soaking and cold-dry tests, delamination of adhered layers surface crack, swelling, and color change were not found when the hot pressing time was over 45 second per milimeter of LVL thickness. As a result of soak under vacuum test shrinkage in the direction of parallel to the grain was about -1.0 percent and. was about 3.0 percent in the direction of the perpendicular to the grain. 6) The film cacks on the LVL's surface after the wet and cold-dry test were not found at all. 7) In the use of the LVL for interior decoration it was considered that the surface of the LVL be overlaid crossly with fancy veneers of birch and paulownia, etc. This cross overlayirg methods have resulted in few cracks on the fancy veneer.

• Journal of Yeungnam Medical Science
• /
• v.20 no.1
• /
• pp.28-35
• /
• 2003

Purpose: To evaluate physeal remodeling after internal fixation of slipped capital femoral epiphysis, We performed a retrospective review of the medical records and radiographs of 14 children (17 cases) who had had slipped capital femoral epiphysis. Materials and Methods: We reviewed 14 patients who had slipped capital femoral epiphysis. They were divided two groups. Group I were in situ pinning with single screw and group II were corrective osteotomy with multiple pinning. We identified physeal remodeling camparing with their preoperative, postoperative and last follow-up radiographs with measuring physeal-shaft angle. Results: Early closure of the physis was observed in 6 cases among 14 patients (17 hips). Compared with their postoperative radiographs, the last follow up radiographic study revealed that physeal remodeling was observed in 4 patients (4 hips) at group I (mean, $7.8^{\circ}$), in 2 patients (3 hips) at group II (mean, $10.7^{\circ}$). Conclusion: In this study, physeal remodeling was observed in 4 patients (4 hips) in group I and 2 patients (3 hips) in group II. The incidence of physeal remodeling was related with degree of epiphyseal slippage, and age was not related with physeal remodeling potential.

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.3
• /
• pp.221-229
• /
• 2011

Due to the increase of oil price and the environmental issue such as the emission of volatile organic compounds, the necessity for developing alternative resins of petroleum-based adhesive resins, which have extensively been used for the manufacture of wood-based products, has been speculation since the early 1990. In our study, rapeseed flour (RSF), which is the by-product of bio-diesel produced from rapeseed, were hydrolyzed by enzymes. As a crosslinking agents of the RSF hydrolyzates, phenol-formaldehyde prepolymers (PF) were prepared. The RSF hydrolyzates and PF were mixed to complete the formulation of RSF-based adhesive resins, and the resins were applied to make the laminated veneer lumber (LVL). The physical and mechanical properties of the LVL were measured to examine whether RSF can be used as raw materials of adhesive resins for the fabrication of LVL or not. The average moisture content and soaking delamination rate of the LVL bonded with RSF-based adhesive resins exceeded the minimum requirement of KS standard. Moreover, thermal analysis of the RSF-based resins showed similar tendencies except for the RSF-based adhesive resins formulated with pectinase-hydrolyzed RSF. The bending strengths of the LVL were higher than that of the LVL made with commercial PF resins. These results showed the potential of RSF as a raw material of alternative adhesives for the production of LVL. Further works on the optimal conditions of RSF hydrolysis and spreading characteristics for RSF-based adhesive resins is required to improve the adhesive performance of RSF-based resins.

• Journal of the Korean Wood Science and Technology
• /
• v.23 no.4
• /
• pp.18-26
• /
• 1995

국내 합판 산업계는 오랫동안 남양재 활엽수를 주로 사용하여 왔으나, 환경 보존적인 측면에서 열대재의 벌채를 규제하는 등 여러 요인으로 인하여 합판용 원목의 수입이 어려워지고 있다. 이에 대응하기 위하여 합판용 원목을 침엽수재로 대체할 필요가 있으며, 침엽수 합판 제조를 위한 기초 자료를 제공하기 위하여 본 연구를 수행하였다. 공시 수종은 국내에서 조림한 낙엽송과 시베리아산 낙엽송 및 뉴질랜드산 라디에타 소나무였으며, 공시원목으로부터 얻어진 단판의 품질과 이들 단판으로 제조한 합판의 접착력과 휨강도를 조사하였다. 이면 할렬실험에서 시베리아산 낙엽송은 다른 수종에 비해 할렬 밀도가 낮게 나타났다. 단판 품질은 접착력 및 휨강도에 거의 영향을 미치지 않았으나 합판의 휨강도에서는 심재와 변재에 따른 차이가 있음을 알 수 있었다. 이는 합판제조사 심재와 변재를 구별하여 사용할 필요가 있었다. 라디에타 소나무의 변재부로 만든 합판 MOR은 다른 수종에 비해 우수하게 나타났다. 접착력 실험에 있어서는 페놀 접착제를 사용하여 만들어진 합판만이 구조용으로써 사용할 수 있음을 알았다. 목파율은 동일 수종 합판에서는 라디에타 소나무 구성이 가장 높게 나타났으며, 이수종(異樹種) 합판에서는 표판을 국산 낙엽송, 심판을 라디에타 소나무를 사용하여 만든 합판에서 가장 높게 나타났다.

• Proceedings of the Acoustical Society of Korea Conference
• /
• autumn
• /
• pp.207-210
• /
• 2004

단판의 차음 성능 해석에 있어서 무한판과 유한판의 가장 큰 음향학적 차이는 유한한 경계에 의해 발생하는 정재파에 있다고 할 수 있다. 하지만, 일치 주파수 이하에서는 진동 공진이 발생하더라도 음향방사효율이 비교적 작고, 따라서, 비록 그 진동 응답이 크더라도 절대적인 음향 방사 양은 작다. 이를 근거로 대부분의 유한판 해석은 비공진 성분에 국한되어 왔으나, 특정 경우 공진 투과 성분을 무시하면 해석 결과에 오차가 발생할 수 있음이 제시된 바 있다. 본 연구에서는 유한 단판의 차음 해석에 있어서 공진 투과 성분의 상대적 기여도를 수치적 해석을 통해 알아보고, 이로부터 공진 투과 성분이 해석치와 측정치 사이의 정량적 상관도에 미치는 영향을 분석하였다.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.4
• /
• pp.407-419
• /
• 2014

The analysis of shape before and after heating, Surface moisture content, Moisture weight change and surface heat distribution by fixed type microwave heating in forms of flat veneer and veneer roll of Korean pine, pitch pine, larch and yellow poplar was conducted. The results were as follows: In case of flat veneer, the quality after microwave heating was comparatively good, but it was somewhat warped. These phenomena may be due to transformation by nonuniform drying stress and stronger effect of local irradiation on the veneers when heating veneer owing to the characteristics of fixed type microwave equipment. In case of the features of roll-shaped veneer heated by microwave, the quality after heating was comprehensively excellent. Especially there was no warping unlike flat veneer. Heat distribution and diffusion were also very stable for roll-shaped veneer and such heat distribution had much influence on surface moisture content and moisture weight loss. Accordingly, the veneer roll would show sufficient drying efficiency in fixed type microwave equipment through a scrutinized examination on generating power and irradiation time according to species and thickness of veneer.

• Journal of the Korean Wood Science and Technology
• /
• v.41 no.1
• /
• pp.42-50
• /
• 2013

Since 1990's, a plywood for flooring base has gotten customers' demand. Costs of raw material and production increased because of changed environment of industry. Tropical timber such as Red Meranti (Shorea acuminate) used for raw material of the floor has been depleting beside countries in South Eastern Asia changed species of afforestation. As a result, it gets hard to secure good quality of raw material for plywood. Moreover plywood price is increased suddenly after earthquake in Japan. Eucalyptus (Eucalyptus globulus) in china has been using for raw material as a countermeasure of changed environment of industry. In this study, possibility of using flooring consisted of Eucalyptus veneer as crossband layers was checked by deflection experiments. Flooring consisted of Red Meranti was used for comparison. Two factors which impact on deflection are a type of density gradient and density difference between Long-grain veneer and Short-grain veneer. Red Meranti samples are M type of density gradient on the other hand Eucalyptus samples are W type of density gradient. The more samples have high density difference, the more deformation was checked. A sample which has big density difference between core and cross bands layer warp more also deform. Flooring was deformed smaller than plywood and samples which have big density difference was deformed more.

• Journal of Biomedical Engineering Research
• /
• v.25 no.5
• /
• pp.361-367
• /
• 2004

The axial compressive strength, relative 3-D stability and osteoconductive shape design of an intervertebral fusion cage are important biomechanical factors for successful intervertebral fusion. Changes in the stress distribution of the vertebral end plate and in cage stability due to changes in the spike shape of a newly contrived box-shaped fusion cage are investigated. In this investigation, the initial contact of the cage's spikes with the end plate and the penetration of the cage's spikes into the end plate are considered. The finite element analysis is conducted to study the effects of the cage's spike height, tip width and angle on the stress distribution of the vertebral end plate, and the micromigration of the cage in the A-P direction. The stress distribution in the end plate is examined when a normal load of 1700N is applied to the vertebra after inserting 2 cages. The micromigration of the cage is examined when a pull out load of l00N is applied in the A-P direction. The analysis results reveal that the spike tip width significantly influences the stress concentration in the end plate, but the spike height and angle do not significantly influence the stress distribution in the end plate touching the cage's spikes. In addition, the analysis results show that the micromigration of the cage can be reduced by adjusting the spike angle and spike arrangement in the A-P direction. This study proposes the optimal shape of an intervertebral fusion cage, which promotes bone fusion, reduces the stress concentration in a vertebral end plate, and increases mechanical stability.

• Korean Journal of Heritage: History & Science
• /
• v.40
• /
• pp.73-104
• /
• 2007

Centering around ruins recognized of being relatively early stage related to flat tile and brick, excavated in Silla capital area, the study attempted elementary approach to seek the appearance time of every remain through comparing them from the excavated cases and production methods of Short beating, Medium beating plate, Long beating plate and Stamped-roof tile. Gyeongju began to use the short beating plate made of tile-less plates or tile plate and increased its quantity. That is deemed to be due to efficiency of beating plate making methods, and moreover to be limited only for use in the palace castle and offices. That is, making short beating plates is presumed to be made merely under some definite objectives. Medium beating plate has been spread to the whole country since Silla and Baekje united. Differently from Koguryo and Baekje, Silla had its unique Beating-plates making technology available for mass-production, which was spread to the whole country and resulted in disappearing of Koguryo and Baekje technology. Long beating plate was not nearly founded in Gyeongju area, but flat tile and common tile excavated in Sachunwang Temple site and Samrang Temple 3rd remains are known. In the outskirts of Gyeongju, long beating plate appeared between the latter half of 8C and the beginning of 9C. Until now, different views have raised to appearance of long beating plate of Unified Silla, which is expected to be clarified under the situation excavated by position relations. Stamped-roof title in Gyeongju is estimated as used after the datum point year 679. While in Baekje area, five stems and branches were involved, in Silla area, code or sign was shown much. The difference between two areas would be due to each other factory, and especially the marked contents werenot letters, which means it had been changed from Baekje s existing-methods. That is, it says the production environment changed owing to Silla's merging. And stamped-roof tile was temporarily used in Gyeongju but soon disappeared, which was because Silla beating plates made under cylinder-shaped tile barrel(圓筒瓦桶) and hitting-pressing of Medium beating plate had beenspread to the whole country, so the production technology of Koguryo and Baekje was naturally dismissed. In consequence, the mergence by Silla brought about unification of each nation's special technology.