• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.12 s.103
• /
• pp.1194-1205
• /
• 2005

This paper proposes a uni-planar elliptical element UWB antenna with band-notched characteristic and modified pound plane fed by CPW. The antenna achieves VSWR below 2 for UWB band(3.1 GHz${\~}$10.6 GHz). In addition, a band-notched characteristic is achieved by inserting a horizontal slot on the radiation element to avoid the interference with 5 GHz(5.15 GHz${\~}$5.825 GHz) band limited by IEEE 802.1la. The antenna has a thin profile, compact size, and ease of manufacture by adopting a CPW feed structure without any additional background plane. Measured data show that the proposed antenna has good return loss below -10 dB, about 2.1 dB${\~}$4.75 dB maximum gain over the bandwidth, omni-directional radiation patterns, linear phase response.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.3
• /
• pp.269-276
• /
• 2001

Ultrasonic testing of composite materials is much more difficult than that of isotropic materials, because of the beam skew phenomenon caused by their elastic anisotropy. An established analytical method exists for elastic wave propagation in anisotropic media as a result of previous research efforts. Yet, due to the complexity of the analytical method, solution of real problems must resort to the numerical method. In this work, analytical solutions have first been obtained for the wavefield due to a point source in a unidirectional fiber-reinforced composite, which may be modeled as transversely isotropic. Then, the corresponding numerical solutions have been obtained using the mass-spring lattice model(MSLM). The two solutions have agreed well with each other. Other problems such as reflection from free boundaries and scattering from cracks have also been solved numerically, and the results have been investigated from the viewpoint of wave mechanics. The numerical model whose validity has been confirmed by this work will be of great use in simulating ultrasonic testing of composite materials.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.4
• /
• pp.610-618
• /
• 2000

A T-shaped microstripline -fed printed slot antenna is anlayzed by using the transmission line model(TLM) in this paper. Microstrip-slotline junction is modeled by employing a transformer and the transformer turn ratio is derived empirically. The method is extended to the case of $1\times2,l\times4$array antennas. Return loss results obtained by using the transmission line model. The maximum measured results and demonstrated the usefulness of the transmission line model. The maximum bandwidths of a single antenna, $1\times2,l\times4$ array antennas are 28.5%, 47.8%, and 50.9%, respectively, for the VSWR$\leq2$. The gain of $1\times4$ array antenna is 7.97dBi and the beamwidth is about $27^{\circ}$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.4
• /
• pp.505-513
• /
• 2000

This study suggests new antenna design for polarization diversity. For dual polarization, two port feeding lines are printed on two separate layers and cross-shaped aperture is located on ground between the substrates. For reducing back radiation, a reflector is attached around $\lambda$/4 behind feeding substrates. For wide bandwidth we use a perturbed patch with saw tooth shaped. This perturbation effect causes reduction of antenna size and also reduction of array size. With the antenna proposed here, $1\times4$ array dual polarization antenna for polarization diversity of PCS base station is built. One single element has as large as 10.3%, 11.3% bandwidths at each port, V.S.W.R less than 1.3 and the isolation is less than -40 dB, also array antenna has 13.2% 12.7% band bandwidth, V.S.W.R less than 1.3 the isolation below -36dB and the XPD of 10 dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.3 s.118
• /
• pp.305-314
• /
• 2007

In this paper, we suggested a CPW-fed UWB antenna with uni-planar sectoral structure. The area where radiation device face ground is designed to have the shape of tapered slot based on exponential function. We modified a rectangular bow-tie dipole structure antenna and thus formed a multi-resonant mode. From this, we expanded the impedance bandwidth and made a feature satisfying VSWR of less than 2 between $3.1\sim10.6GHz$. The test result showed that the return loss less than -10 dB was met in the full-band UWB system and maximum gain of $0.9\sim3.1dB$ was made with the half-power beamwidth of $40.1\sim89.9^{\circ}$ on XY plane(Theta, $Phi=90^{\circ}$) and the full band. By using CPW-fed structure with no ground on the back of the substrate, the suggested antenna is easy to design and its miniaturization is also possible.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.1
• /
• pp.25-33
• /
• 1998

In this paper, we describe a single-gate MESFET mixer at PCS(Personal Communication Service) frequency band. The PCS frequency band is 1965~2025 MHz in FR and 140 MHz in IF irrespectly. The design of the mixer was executed by microwave simulator, EEsof Libra. The matching network is consisted of rectangular inductor, MIM capacitor and open stub. The ma- nufacture work was accomplished by the micro-pen and wedge-bonder. The mixer showed $6.69\pm0.65$ dB of conversion gain, $-14.9\pm3.5$dB of RF reflection coefficient and 57.83 dB of LO/IF isolation at 10 dBm of LO power when LO frequency is 1855 MHz. When this mixer is used at PCS terminal, IF-amplifier which compensates the conversion loss of diode mixer may be omitted.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.30 no.5
• /
• pp.373-379
• /
• 2019

If two signals with the same single-tone frequency and differing phases impinge simultaneously on an antenna at slightly differing angles, then a large error in the angle estimation might occur if the phase difference is either $0^{\circ}$ or $180^{\circ}$. This phenomenon might arise with an airborne fire-control radar, which has a relatively small bandwidth, for a low-flying target over the sea or terrain surface. In this paper, we show that the $Cram{\acute{e}}r$-Rao lower bound for such a target can be significantly lowered with the use of two frequencies.

• Journal of Advanced Navigation Technology
• /
• v.23 no.5
• /
• pp.430-436
• /
• 2019

It is needed to develop an antenna with features of subminiature, light weight and multi-band operation for the variaty services in maritime and industrial fields. The PCB pattern antenna is one of the appropreiate antennas solving these requirements. In this research, the design and fabrication of the PCB pattern antenna operating on the single band of 920 MHz are investigated. The final goal is that the development of the dual band PCB pattern antenna operating on 260 MHz and 920 MHz, which is based on the proposed antenna. It is evident that the performance in the frequencies of 902 MHz, 915 MHz and 928 MHz among of 920 MHz ISM band is better than that in other frequencies. It is also confirmed that the differences of the voltage standing wave ratio, return loss, gain and efficiency between three frequencies are less than 5%. It is expected that the development of communication link of 5-10 km is possible when the induced results are applied into the low power wide area (LPWA) network desinged by the rule of -30 dB sensitivity.

• Korean Journal of Optics and Photonics
• /
• v.31 no.6
• /
• pp.268-273
• /
• 2020

We analyze the characteristics of the coherent beam combination of lasers by monitoring the speckle pattern of the beam reflected from a scattering medium. Three collimated laser sources with high coherence are focused on a scattering target using a lens, and we then examine the speckle pattern of the returned beam in the Fourier domain. We observe that the size of the speckle pattern changes, depending on the focused-beam size or degree of spatial overlap of the three beams. Furthermore, through Fourier-domain analysis of the speckle pattern we obtain the monitoring variable to qualify the efficiency of the coherent beam combination.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.3
• /
• pp.83-89
• /
• 2018

The thermal characteristics of concrete specimens were analyzed using cement paste specimens with artificial cracks. In order to understand the temperature characteristics of the specimen depending on the crack depth, the specimen was heated and the minimum temperatures of the specimens at which cracks appear were investigated according to the crack depth. It was confirmed that the surface temperature distribution of the specimen varies depending on whether the specimen is cracked or not, because of the single and multiple reflections of the incident energy. Furthermore, as the temperature distribution of the specimen reaches a steady state, the temperature data tends to decrease with the crack depth. Through the observation of the normalized temperatures, it was found that the temperature of the specimens obtained from this experiment reached a steady state after 10 minutes. At this time, the standard deviation of the normalized temperature is around 0.01 or less, and the temperature decreases linearly with increasing crack depth. This result is considered to be closely related to the area where multiple reflections occur in the cracked region. If the correlation between the crack region and the incident energy is analyzed for various specimens, it can be applied to the diffuse reflection of the light.