• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.2
• /
• pp.119-127
• /
• 2011

Objective of this study is to identify properties on strength increase of hardened concrete and fluidization of non-hardened concrete using waste ceramics generated by construction waste, which is a type of industrial waste, and by ceramics, which is a clay plastic, during its production process, and determine length change ratio caused by drying shrinkage during substitution of recycle aggregate and waste ceramics, and whether they can be used as concrete compounds. Slump of non-hardened concrete exhibited the best fluidization and formability at recycled aggregate's replacement ratio of 60% driven by higher substitution ratio of recycled aggregate and waste ceramics while air content met the KS requirement when substitution ratio of waste ceramics was $4,000cm^2/g$. Compressive strength of hardened concrete exceeded the requirements at early age and standard age and temperature dropped by roughly $6{\sim}10^{\circ}C$ less than the standard at maximum temperature in adiabatic temperature increase, which will hopefully result in stronger durability.

• Korean Chemical Engineering Research
• /
• v.52 no.6
• /
• pp.720-726
• /
• 2014

PEM fuel cell vehicles have been getting much attraction due to a sort of highly clean and effective transportation. The onboard fuel processor, however, is inevitably required to supply the hydrogen by conversion from some fuels since there are not enough available hydrogen stations nearby. A lot of studies have been focused on analyses of ATR reactor under the assumption of thermo-neutral condition and those of the optimized process for the minimization of energy consumption using thermal efficiency as an objective function, which doesn't guarantee the maximum hydrogen production. In this study, the analysis of optimization for 100 kW PEMFC onboard fuel processor was conducted targeting various fuels such as gasoline, LPG, diesel using newly defined hydrogen efficiency and keeping simply synthesized heat exchanger network regardless of external utilities leading to compactness and integration. Optimal result of gasoline case shows 9.43% reduction compared to previous study, which shows the newly defined objective function leads to better performance than thermal efficiency in terms of hydrogen production. The sensitivity analysis was also done for hydrogen efficiency, heat recovery of each heat exchanger, and the cost of each fuel. Finally, LPG was estimated as the most economical fuel in Korean market.

• 한국가스학회:학술대회논문집
• /
• 2003.10a
• /
• pp.65-72
• /
• 2003

현행 가스법상 지상식 LNG 저장탱크에 있어서 일정 용량의 저장탱크 주위에는 액상의 가스가 누출된 경우에 그 유출을 방지할 수 있는 방류둑(Dike) 또는 이와 동등 이상의 효과가 있는 시설을 설치하도록 규정하고 있어, 실제로 모든 지상식 LNG 저장탱크에 대해서 별도의 방류둑 설치를 의무화하고 있다. 또한, 예외규정으로 국제기준(international codes and standards)에 의해 설계되는 저장탱크는 심의를 통해 방류둑 기능을 인정할 수 있도록 하고 있다. 외국의 경우 LNG 저장탱크는 일반적으로 자국내 법령보다는 국제기준에 의해 건설됨으로써 1차 탱크로부터 일정거리의 둘레에 방류둑이 필요한 단일방호식 저장탱크 이외에 이중방호식, 완전방호식(full-containment) 및 멤브레인식(membrane) 저장탱크의 경우 외부(콘크리트, 강재)탱크가 방류둑 기능을 가지고 있어 별도의 방류둑이 필요없는 구조로 규정하고 있다. 멤브레인 LNG 저장탱크의 경우 프랑스, 일본 및 한국이 설계기술을 보유하고 있고, 최근 프랑스 및 한국에서 별도의 방류둑 없는 지상식 멤브레인 저장탱크 건설이 추진되고 있으나 양국 모두 자국법의 방류둑 규정에 의해 건설의 장애요소로 작용하고 있다. 따라서 지상식 멤브레인 LNG 저장탱크의 방류둑 기능에 대한 각 국의 법령 및 기준을 조사하고, 방류둑 일체형 저장탱크(완전방호식 및 멤브레인 저장탱크)의 형식별 안전성 평가 자료를 비교 검토함으로써 방류둑 일체형 멤브레인 저장탱크의 국내 도입의 타당성을 검토하고자 하였다. 조사결과 유럽, 미국 및 일본에서는 이중벽 LNG 저장탱크의 경우 콘크리트 외부탱크가 방류둑 기능을 가지는 것으로 규정하고 있으며, 특히 EN 1473과 제정중인 prEN 265002에서는 멤브레인 저장탱크의 경우 내부 멤브레인 탱크 누출시 단열시스템과 함께 외부 콘크리트 탱크가 액밀성 및 기밀성을 동시에 가지는 것으로 별도의 방류둑이 불필요함을 규정하고 있다. 프랑스 및 일본의 방류둑 일체형 LNG 저장탱크에 대한 위험성 평가 결과를 검토한 결과 멤브레인 저장탱크와 완정방호식 저장탱크는 안전성 차원에서 거의 동일한 것으로 나타났다. 따라서 국내에서 개발한 지상식 멤브레인 LNG 저장탱크 설계모델에 대한 안전성 제고 및 안전성 평가 등을 통해 객관적인 안전성 근거가 확보된다면 동 탱크의 경우에도 완전방호식 LNG 저장탱크와 같이 외부콘크리트 저장탱크의 방류둑 기능인정이 가능할 것으로 판단된다.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.66.1-66.1
• /
• 2011

반도체를 비롯하여 LCD, OLED와 같은 디스플레이 (FPD: Flat Panel Display) 분야는 국가 선도 사업으로써 발전을 거듭해오고 있다. 하지만 기술의 성숙도가 높아짐에 따라 최근 중국과 대만 업체와의 경쟁이 심화되고 있으며, 더불어 환경문제가 큰 이슈로 떠오르고 있어 신기술 개발을 통한 생산 수율 향상 및 친환경 공정 개발의 중요성이 커지고 있다. 반도체, 디스플레이 공정에서 생산 수율 저하의 주요 원인으로써 공정 중 발생하는 미세 오염 입자를 들수 있다. 반도체 및 디스플레이 공정에서 세정 기술은 전체 기술의 30% 이상을 차지하며 생산 수율 및 제품의 품질에도 큰 영향을 주는 공정이다. 세정 공정은 일반적으로 습식 세정 공정이 낮은 공정비용을 바탕으로 널리 적용되어 왔으나, 기판의 대형화와 패턴의 미세화에 따라 정밀한 세정 스펙이 요구되며 더불어 막대한 양의 초순수와 화학액의 사용으로 인한 공정비용 증가와 환경 규제 강화에 따른 폐수 처리의 문제에 직면하고 있다. 이에 따라 폐수의 양을 줄이며 건조공정을 필요로 하지 않아 공정비용을 줄일 수 있는 건식 세정 공정에 대한 연구가 활발히 진행 되고 있다. $CO_2$ snow jet 세정 기술은 건식 공정으로써 $CO_2$ 가스를 특수하게 제작된 분사 노즐에서 고압으로 가스를 분사하여 이 때 발생되는 순간적인 감압에 의한 단열 팽창으로 생성된 $CO_2$ snow 입자가 기판 표면의 오염물과 물리적 충돌을 하어 세정이 이루어지는 기술이다. 특히 $CO_2$ 세정은 환경과 인체에 무해하며 공정 후 바로 승화하기 때문에 추가적인 폐수처리 공정 등이 필요하지 않고, 건식 공정으로써 수세(Rinse) 공정을 필요로 하지 않기 때문에, 공정비용을 크게 줄일 수 있으며 물반점 발생을 방지 할 수 있는 친환경 건식 공정으로써의 장점을 가지고 있다. 본 연구에서는 자체적으로 개발한 $CO_2$ snow jet을 바탕으로 하여 다양한 공정조건을 변화시켜 세정효율을 측정하는 한편, 최적화 하기 위한 연구를 진행하였으며 더불어 $CO_2$ snow의 세정력을 정량적으로 평가하기 위한 연구를 진행하였다. 실험을 통해 가장 효과적으로 $CO_2$ snow 입자를 배출 할 수 있는 공정 조건으로써 5 bar의 캐리어 가스 압력을 사용하여, 세정력에 가장 큰 영향을 줄 수 있는 분사 노즐과 기판 사이의 거리 및 분사 노즐의 각도 등을 변화시켜 각 조건에 따른 세정효율을 평가하였다. 세정 오염물은 Silica, PSL 표준 입자(Duke scientific, USA)를 정량적으로 웨이퍼에 오염 시킨 후, 파티클 스캐너(Surfscan 6500, KLA-Tencor, USA)를 이용하여 세정 전 후의 오염입자 개수 변화를 통해 정량적으로 세정효율을 평가하였다. 본 연구를 통하여 $CO_2$ snow jet를 이용한 친환경 고효율 건식 세정 공정 메커니즘을 분석하였으며, 노즐과 기판 사이의 간격 및 분사 노즐의 각도 등을 최적화 한 세정 공정을 얻을 수 있었다.

• Journal of the Korea Concrete Institute
• /
• v.15 no.2
• /
• pp.254-262
• /
• 2003

In this study, the results of applying cold weather concreting mixed with Accelerator for Freeze Protection(AFP) to full scale structures are presented. Since the determination of W/C and amount of AFP significantly have an effect on strength gain and protection of frost damage in early, a full investigation is needed to determine these values at stage of nux design. The flowability of fresh cold weather concreting with AFP was similar to the same W/C. Lower loss of workability and initial slump flow of concrete using superplasticizer of polycarboxylic ester than that of melamine sulphonate showed that polycarboxylic ester was more effective on elapsed time. Temperature histories of specimens located in insulation boxes at the site was similar to that of structures. Thus, it is cleared that simple adiabatic curing method is effective for evaluating in-place concrete strength than specimens cured by sealing method. The investigation results of development of compressive strength of cold weather concreting included AFP with curing methods by logistic curves indicated that AFP can be effective to gain strength at lower temperature than normal curing temperature. In field testing, vinyl sheets were placed over the concrete sections and AFP enabled concrete to gain $5N/{mm}^2$ to protect frost damage in early ages and specified compressive strength of concrete at 28 days under average temperature of $-2^{\circ}C$ (lowest temperature was $-12^{\circ}C$) during site application.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.12
• /
• pp.1193-1199
• /
• 2012

A cup burner experiment was performed to investigate the effect of the oxidizer velocity and concentration on flame instability near extinction. Heptane was used as a fuel and air diluted by nitrogen and carbon dioxide was used in the oxidizer stream. Two types of flame instabilities at the flame base and at axial downstream were observed near extinction. The instability at the flame base could be characterized by cell, swing, and rotation modes, and the cell mode changed to the rotation mode through the swing mode as the oxidizer velocity increased. To assess the parameters for the flame instability, the initial mixture strengths, Lewis number, and adiabatic flame temperature were investigated under each condition. The Lewis number might be the most important among them, but it is impossible to generalize because of the insufficient number of cases. Furthermore, the axial periodic flickering motion disappeared at low and high oxidizer velocities near extinction. This resulted from the fact that low oxidizer velocity induced evaporated fuel velocity below the critical velocity and high velocity made the reacting fuel velocity comparable.

• Fire Science and Engineering
• /
• v.29 no.6
• /
• pp.40-44
• /
• 2015

National and international standards for curtain wall glass are focused on wind pressure and insulation performance, but disasters such as fires and earthquakes are not considered. Failure of curtain wall glass during a fire in a skyscraper increases the loss of lives and property due to the spread of fire. Therefore, the fire resistance of curtain wall glass should be investigated, and technology to prevent glass failure should be developed to prevent fire damage due to spreading fire. It is important to predict the starting point of cracks and the cause of glass failure to prevent it effectively using the limited water in a skyscraper. In this study, double glazed glass was exposed to a radiator in an experiment performed to analyze the thermal characteristics. The results show that glass that was not directly exposed to high temperature and pressure was broken. To identify this failure case, numerical analysis was performed. Three glass specimens were installed in an ISO 9705 room and exposed to radiation using a radiator, and a thermocouple was used to measure the temperature on the surface of the glass. Widely used double glazed glass was analyzed for weakness to fire.

• Economic and Environmental Geology
• /
• v.35 no.5
• /
• pp.407-420
• /
• 2002

The Buddhist Triad Cave in Gunwi (National treasure No. 109) consists of porphyritic biotite granite, and it has been deteriorated into microorganic smears, white films, brown rusts, granular decay, color changes, and joints by the same weathering factors as rain, moisture, temperature variation and microorganic living. Main origin is probably the rain that leaks into the cave along joints in Palgongsan granite, and then its moisture grows many microorganism and is frozen over during winter. The granites around the cave regularly develop two NEE and NWW joint sets that are conjugate to be a joint system. The NEE set extends far away with narrow joint spacings and affects the leakage of the rains, and is divided into 4 joint zones, among which J$_{m}$ and J$_{3}$ immediately affect the leaking water into the cave. An extensional Joint, in northern wall of the cave, was formed by toppling of the block between J$_{m}$and J$_{3}$joint zones from widening the Jm aperture by roots of a big pine tree, and passes through the J$_{m}$joint zone. This bypass allows no circulation of small rain, but a good circulation of heavy rain from influx to the cave for a long pathway. Many Joints and cracks, in the ceiling near the cave entrance, immediately get through the J$_3$ joint zone, and have a good circulation of small rain 10 mm. Both J$_{m}$and J$_{3}$ joint zones are, therefore, chief influxes that cause leakage of the rains.

• Horticultural Science & Technology
• /
• v.29 no.2
• /
• pp.102-109
• /
• 2011

This research was conducted to establish efficient methods to control root-zone temperature of tomato plant when cultivated in perlite bag during the summer season. Tomato plants were grown with four selected treatments; covering irrigation pipe by aluminum insulation material (Insulate), discarding nutrient solution inside the irrigation line before each irrigation (Discard), skipping irrigation for two hours from 13:00 to 15:00 (Skip), or no treatment as a control (Non). Based on the analysis of plant development index, all plants with selected treatments grew more vigorous and vegetative in similar growth patterns. The discard treatment exhibited the best root-zone temperature control among the treatments. The discard treatment also resulted in the best root growth and above-ground growth, followed by skip, Insulate and Non. The total yields were obtained by the order of Insulate, Discard, Non and Skip. However the marketable yield was obtained by the order of Discard, Insulate, Skip and Non. The net incomes treated with Discard and Insulate were 9,687,600 and 9,396,000 Korean won per hectare, respectively, exhibiting higher incomes than that of Non. Therefore, it was concluded that insulation of the irrigation pipe and discarding nutrient solution inside the pipe before each irrigation were the most desirable and economical methods in terms of costs and yields.

• Nuclear Engineering and Technology
• /
• v.27 no.3
• /
• pp.301-316
• /
• 1995

experimental and computational studies ore carried out to investigate the natural convection of the single phase flow in a tank with a heated horizontal plate facing downward. This is a simplified model for investigations of the influence of a core melt at the bottom of a reactor vessel on the thermal hydraulic behavior in a oater filled cavity surrounding the vessel. In this case the vessel is simulated by a hexahedron insulated box with a heated plate Horizontally mounted at the bottom of the box. The box with the heated plate is installed in a water filled hexahedron tank. Coolers are immersed in the U-type water volume between the box and the tank. Although the multicomponent flows exist more probably below the heated plate in reality, present study concentrates on the single phase flow in a first step prior to investigating the complicated multicomponent thermal hydraulic phenomena. In the present study, in order to get a better understanding for the natural convection characteristics below the heated plate, the velocity and temperature are measured by LDA(Laser Doppler Anemometry) and thermocouples, respectively. And How fields are visualized by taking pictures of the How region with suspended particles. The results show the occurrence of a very effective circulation of the fluid in the whole How area as the heater and coolers are put into operation. In the remote region below the heated plate the new is nearly stagnant, and a remarkable temperature stratification can be observed with very thin thermal boundary. Analytical predictions using the FLUTAN code show a reasonable matching of the measured velocity fields.